1. Introduction
This manual provides essential information for the safe and effective use of your Heltec Lithium Titanate (LTO) Battery Management System (BMS). This BMS is designed to protect and balance multi-string LTO battery packs, supporting configurations from 4S to 10S with a continuous discharge current of 15A and a maximum current of 20A.
2. Product Overview
The Heltec LTO BMS is a crucial component for managing Lithium Titanate battery packs. It ensures the longevity and safety of your battery by providing protection against overcharge, over-discharge, overcurrent, short circuit, and over-temperature conditions. It also features a balancing function to maintain cell voltage consistency across the battery pack.

Figure 1: Heltec LTO BMS (Front view with wires)

Figure 2: Heltec LTO BMS (Top view of components)

Figure 3: Heltec LTO BMS (Bottom view of components)
3. Specifications
The following table details the key parameters and specifications of the Heltec LTO BMS:
| Project | Standard Value |
|---|---|
| Protection Parameters | |
| Normal charging input voltage (maximum) | Each section 2.80V |
| Normal charging working current (maximum) | 15A/20A |
| Normal charging overcharge protection voltage | 2.80V |
| Normal charging over discharge protection voltage | 1.80V |
| Discharge nominal working current/Working current (maximum) | 15A/20A |
| Overcurrent protection current and delay | 60A/300mS |
| Short circuit protection and delay | <500uS |
| Protection board over temperature protection temperature and delay | 65°C |
| Protection board working temperature adaptation range | (-20°C, 65°C) |
| Balance Management Part | |
| Balanced starting voltage | 2.40V |
| Balanced current | 50mA (Energy-consuming) |
| Protection Board Basic Parameters | |
| Protection board static power consumption | ≤100uA (Power consumption of the protection board in the sleep state) |
| Protection board work power consumption | ≤300uA (Power consumption of the protection board in the activation state) |
| Protection board internal resistance | Discharge path ≤10mΩ, Charge path ≤15mΩ |
| Protection board size | 50*45*6mm |
Figure 4: Protection Board Parameter Table
4. Setup & Installation
This BMS supports 4 to 10 strings of Lithium Titanate batteries. The overcharge and over-discharge protection voltages are configurable. Please ensure correct wiring according to the diagrams below. Incorrect wiring can damage the BMS or battery pack.
4.1 Configurable Parameters
The board's overcharge and over-discharge parameters can be configured. If you have specific requirements, please communicate them at the time of purchase. Otherwise, factory default parameters will be applied.
- Overcharge Point: 2.8V - 4.375V (configurable in 25mV steps)
- Over-discharge Point: 1.4V - 2.900V (configurable in 100mV steps)
4.2 Factory Default Configuration Parameters (Examples for various battery types)
While this BMS is for LTO, here are common default settings for various battery chemistries for reference:
- A: 3.7V Lithium Cobalt Oxide Battery Group: Overcharged 4.25V, Over-discharged 2.50V
- B: 3.7V Ternary Lithium Battery Group: Overcharge 4.20V, Over-discharge 2.80V
- C: 3.2V Iron Phosphate Battery Group: Overcharged 3.65V, Over-discharged 2.50V
- D: 3.8V High Voltage Lithium Battery Pack: Overcharge 4.45V, Over discharge 3.00V
- E: 2.4V Lithium Titanate Battery Group: Overcharge 2.80V, Over-discharge 1.80V
4.3 Wiring Diagrams
There are two common wiring methods: "Same Mouth Connection" (common port for charge/discharge) and "Split Connection" (separate ports for charge/discharge). Choose the appropriate diagram for your application.
4.3.1 Same Mouth Connection (Common Port)
In this configuration, the charging and discharging current flows through the same port (P-). This simplifies wiring but may have limitations on simultaneous charge/discharge if not designed for it.

Figure 5: Same Mouth Connection Wiring Diagram
Connection Points:
- BAT-: Connect to the negative terminal of the battery pack.
- P-: Connect to the common negative terminal for both charger and electrical equipment.
- PACK+: Connect to the positive terminal of the battery pack, charger, and electrical equipment.
- B1+, B2+, B3+...Bn+: Connect these balance wires to the positive terminals of each individual battery cell, starting from B1+ (first cell positive) up to Bn+ (last cell positive).
4.3.2 Split Connection (Separate Ports)
This configuration uses separate ports for charging (CHG-) and discharging (DSG-), allowing for potentially higher current handling or specific application requirements.

Figure 6: Split Connection Wiring Diagram
Connection Points:
- BAT-: Connect to the negative terminal of the battery pack.
- CHG-: Connect to the negative terminal of the charger.
- DSG-: Connect to the negative terminal of the electrical equipment.
- PACK+: Connect to the positive terminal of the battery pack, charger, and electrical equipment.
- B1+, B2+, B3+...Bn+: Connect these balance wires to the positive terminals of each individual battery cell, starting from B1+ (first cell positive) up to Bn+ (last cell positive).
Important: Always double-check all connections before applying power to prevent damage to the BMS, battery, or connected equipment. Ensure the balance wires are connected in the correct sequence and to the correct cell terminals.
5. Operation
Once correctly installed, the Heltec LTO BMS operates automatically to manage and protect your battery pack. It continuously monitors cell voltages, total pack voltage, and current flow.
- Overcharge Protection: Prevents individual cells from being charged beyond their safe voltage limit (default 2.80V for LTO).
- Over-discharge Protection: Prevents individual cells from being discharged below their safe voltage limit (default 1.80V for LTO).
- Overcurrent Protection: Shuts off discharge if current exceeds the safe limit (60A with 300mS delay).
- Short Circuit Protection: Provides rapid shutdown in case of a short circuit (<500uS delay).
- Over-temperature Protection: Disables operation if the board temperature exceeds 65°C.
- Cell Balancing: Actively balances cell voltages when the balanced starting voltage (2.40V) is met, ensuring all cells are at a similar state of charge.
6. Maintenance
The Heltec LTO BMS is designed for reliable operation with minimal maintenance. However, following these guidelines can help ensure its longevity:
- Keep the BMS clean and free from dust and debris.
- Avoid exposing the BMS to moisture or corrosive environments.
- Ensure adequate ventilation around the BMS, especially during high current operation, to prevent overheating.
- Periodically inspect all wiring connections for tightness and signs of wear or corrosion.
- Operate the BMS within its specified temperature range (-20°C to 65°C).
7. Troubleshooting
If you encounter issues with your Heltec LTO BMS, consider the following basic troubleshooting steps:
- No output/BMS not activating:
- Check all wiring connections for correctness and secure contact.
- Verify that the battery pack voltage is within the safe operating range (above over-discharge protection).
- Ensure the charger is connected correctly and providing the expected voltage.
- Battery not balancing:
- Confirm that the battery pack is being charged and the cell voltages are above the balanced starting voltage (2.40V).
- Check balance wire connections for continuity and correct order.
- BMS frequently cutting off:
- This could indicate an overcurrent condition. Check the load connected to the battery for excessive current draw.
- Verify that the battery pack can supply the required current without significant voltage sag.
- Check for short circuits in the load or wiring.
- Ensure the operating temperature is within the specified range.
For complex issues or if troubleshooting steps do not resolve the problem, please contact technical support.
8. User Tips
No specific user tips were available from reviews or Q&A for this product. General best practices for BMS usage include:
- Always use a compatible charger designed for Lithium Titanate batteries.
- Ensure your battery cells are of similar capacity and internal resistance for optimal balancing performance.
- When assembling a battery pack, pre-balance individual cells to a similar voltage before connecting them to the BMS.
9. Warranty & Support
For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.