1. Product Overview
The FLIPSKY Mini FSESC6.7 70A is an advanced Electronic Speed Controller (ESC) designed for brushless DC motors, based on the VESC6.6 platform. It features an aluminum anodized heat sink for efficient thermal management and supports a wide range of battery configurations and control modes. This manual provides essential information for the safe and effective use of your FLIPSKY Mini FSESC6.7 70A.


2. Specifications
| Feature | Description |
|---|---|
| Firmware | Latest Version |
| Continuous Current | 70A |
| Instantaneous Current | 200A |
| Voltage Range | 8V-60V (4-13S LiPo, safe for 4S to 12S LiPo; voltage spikes must not exceed 60V) |
| BEC Output | 5V@1A |
| EPRM | 150000 |
| Dimensions (L x W x H) | 67mm x 39mm x 18.7mm (including heatsink) |
| Motor Wire Gauge | 12AWG |
| Power Cable Gauge | 12AWG |
| Material | Metal (Heatsink) |
| Recommended Age | 14+ years |
| Use | Vehicles & Remote Control Toys |
| Certification | CE, RoHS |

3. Features
- Supports BLDC square wave mode control and FOC sine wave mode.
- USB online firmware update capability.
- Supports three control modes: Current, Duty Cycle, Speed Control, and Position Control.
- Equipped with 6 NVMFS5C612NL high current MOS transistors (60V/235A).
- Compatible with Hall sensors (ABI, HALL, AS5047, AS5048A) and sensorless Hall configurations.
- Adjustable protection measures: low input voltage, high input voltage, large motor current, high input current, and over-temperature protection for both MOSFET and motor.
- Supports various control communication methods: PPM, ADC, NRF, UART.
- Multiple communication ports: USB, CAN, UART, SPI, IIC.
- Supports balancing car functionality by connecting an IMU module (e.g., MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160) via the IIC interface.
- Features high regenerative braking current (with separate limits for motor and input) and high RPM (with different limits for each direction).
- Nearly one hundred setting parameters can be modified and saved via the USB port using the VESC_TOOL host computer software.
- Digital VCC and analog VCC are generated by separate voltage regulators for enhanced AD conversion accuracy.
- Integrated aluminum alloy heat sink for improved heat dissipation and extended product lifespan.
4. Setup Instructions
Before connecting, ensure all components are compatible and power is disconnected. Proper soldering and connections are crucial for safe operation.
4.1. Package Contents

4.2. Wiring Diagram
Refer to the detailed wiring diagram below for correct connections. Incorrect wiring can damage the ESC or connected components.

4.3. Connection Steps
- Prepare Connectors: If not already attached, solder appropriate connectors (e.g., XT60/XT90 for battery, 4mm bullet connectors for motor phases) to your battery and motor wires. Ensure proper polarity (red for positive, black for negative).
- Connect Motor to ESC: Connect the three phase wires from your brushless DC motor to the corresponding 'A', 'B', 'C' terminals on the ESC. The order of these connections can affect motor direction, which can be adjusted in the VESC_TOOL software.
- Connect Hall Sensors (Optional): If your motor has Hall sensors, connect the sensor cable from the motor to the Hall sensor port on the ESC. Ensure the pinout matches (5V, GND, and signal wires).
- Connect Battery: Connect your LiPo battery to the main power input of the ESC. Double-check polarity before connecting to avoid damage.
- Connect Receiver/Control Input: Connect your receiver or other control input device (e.g., PPM, UART, NRF) to the appropriate port on the ESC.
- Connect to PC (for configuration): Use the provided USB cable to connect the ESC to your computer for initial setup and configuration via the VESC_TOOL software.
4.4. Installation and Testing Demonstration
Watch this video for a visual guide on connecting the ESC, motor, and performing a basic test.
5. Operating Instructions
The FLIPSKY Mini FSESC6.7 70A is configured and operated using the VESC_TOOL software. This powerful tool allows for detailed customization and monitoring.
5.1. VESC_TOOL Software
- Download and Install: Obtain the latest VESC_TOOL software from the official VESC project website.
- Connect ESC: Connect your ESC to your computer via USB.
- Auto-Connect: Launch VESC_TOOL and use the 'Autoconnect' feature to establish communication with your ESC.
- Motor Setup Wizard: Follow the Motor Setup Wizard to automatically detect and configure your motor parameters. This is crucial for optimal performance and to prevent damage.
- App Configuration: Configure your desired control application (e.g., PPM for remote control, UART for external microcontrollers) under the 'App Configuration' section.
- Parameter Adjustment: Fine-tune various parameters such as current limits, voltage limits, temperature limits, and regenerative braking settings according to your specific application and motor.
- Firmware Update: Regularly check for and update the ESC firmware via the VESC_TOOL to ensure you have the latest features and bug fixes.
5.2. Control Modes
The ESC supports the following control modes, configurable via VESC_TOOL:
- Current Control: Directly controls the motor current.
- Duty Cycle Control: Controls the motor by adjusting the PWM duty cycle.
- Speed Control: Maintains a target motor speed (RPM).
- Position Control: Controls the motor to a specific angular position.
6. Maintenance
To ensure the longevity and optimal performance of your FLIPSKY Mini FSESC6.7 70A, follow these maintenance guidelines:
- Keep Dry: Protect the ESC from moisture and water exposure. While the heatsink provides some protection, the board itself is not waterproof.
- Cleanliness: Keep the ESC free from dust, dirt, and debris. Use compressed air or a soft brush to gently clean the heatsink and components.
- Inspect Connections: Periodically check all soldered connections and wire harnesses for signs of wear, corrosion, or loose contacts. Re-solder or replace as necessary.
- Thermal Management: The aluminum heatsink is designed for efficient heat dissipation. Ensure it is not obstructed and has adequate airflow, especially during high-load operations.
- Firmware Updates: Keep the firmware updated to benefit from performance improvements and bug fixes.
7. Troubleshooting
This section outlines common issues and their potential solutions. Always disconnect power before inspecting or making changes to the ESC.
7.1. Common Issues and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor not spinning / No response | Incorrect wiring, power issue, VESC_TOOL configuration error, sensor issue. | Check all power and motor connections. Verify battery voltage. Re-run Motor Setup Wizard in VESC_TOOL. Check sensor connections if applicable. |
| ESC overheating | Excessive load, insufficient cooling, incorrect motor parameters. | Reduce load. Ensure adequate airflow around the heatsink. Check motor current limits in VESC_TOOL. |
| Sudden power cut-off | Over-voltage/under-voltage protection, over-current protection, over-temperature protection triggered. | Check battery voltage. Review VESC_TOOL logs for fault codes. Adjust protection thresholds if appropriate for your setup, but exercise caution. |
| Unstable motor operation | Incorrect motor detection, noisy sensor signals, loose connections. | Re-run motor detection. Check sensor wiring for interference. Secure all connections. |
| Cannot connect to VESC_TOOL | USB cable issue, driver problem, ESC not powered, incorrect COM port. | Try a different USB cable. Install necessary USB drivers. Ensure ESC is powered. Select the correct COM port in VESC_TOOL. |
7.2. Protection Functions
The ESC is equipped with several protection functions to prevent damage:
- Low Input Voltage Protection
- High Input Voltage Protection
- Large Motor Current Protection
- High Input Current Protection
- Over-Temperature Protection (for MOSFETs and motor)
If any of these protections are triggered, the ESC may reduce power or shut down. Consult VESC_TOOL logs for specific fault indications.
8. Warranty and Support
FLIPSKY provides warranty coverage for its products under specific conditions. Please review the following policy details:
8.1. Warranty Period
- Consumable Electronic Products (e.g., VESC, Motor, Battery): 2 months from the 7th day after shipment (checked by logistic record).
- Non-Electronic Products: 2 months from the 7th day after shipment (checked by logistic record).
If a product is found to be defective within the warranty period, FLIPSKY may offer repair or replacement. If repair is not feasible, a discount may be provided for a new replacement (excluding shipping costs).
8.2. Conditions Not Covered by Warranty
The following conditions will void the product warranty:
- Physical damage to electronic components or PCB.
- PCB board has repair soldering iron traces (excluding soldered cable bullet connectors).
- Water damage or external impact damage.
- Abnormal applications beyond the product specifications.
- Products not purchased directly from FLIPSKY.net (contact original purchase channel).
- For group-buy items, the warranty period is 7 days after shipment.
- For personal second transactions, the warranty is invalid unless the original source order number is provided.
- Warranty is valid only once per product.
All products are tested before shipment. However, FLIPSKY is not liable for any damage caused by incorrect installation or configuration of VESC/motor settings. Please ensure correct setup before use.
If your product is out of warranty, repair services may be provided for a reasonable charge.
This warranty policy was last updated on 2018/11/1 and previous policies are superseded.
9. User Tips
- Raspberry Pi Connectivity: The ESC can be connected to a Raspberry Pi or similar microcontrollers using the TX/RX pins for UART communication, allowing for custom control and data logging.
- Radio Control: For wireless control, the ESC supports NRF communication, enabling integration with compatible radio systems.
- Configuration Best Practices: Always perform the motor detection wizard in VESC_TOOL for accurate motor parameter setup. Incorrect settings can lead to inefficient operation or damage.
- Voltage Spikes: Pay close attention to the maximum voltage rating (60V). Voltage spikes from regenerative braking or inductive loads can exceed the battery voltage. Ensure your system design accounts for this to prevent damage.