JETTING 303-1AH-C-R1 U01, 301-1C-C-R1

Contents

JETTING Automotive Relay Instruction Manual

Models: 303-1AH-C-R1 U01 (4-pin), 301-1C-C-R1 (5-pin)

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your JETTING Automotive Relay. These relays are designed for various automotive applications, providing reliable switching for high-current circuits using a low-current control signal. Please read this manual thoroughly before use to ensure safe and efficient operation.

2. Product Specifications

Feature Specification
Brand JETTING
Model Numbers 303-1AH-C-R1 U01 (4-pin), 301-1C-C-R1 (5-pin)
Voltage 12V DC
Pin Configuration 4-pin or 5-pin
Current Rating 35A (4-pin), 20A (5-pin)
Theory Reed Relay
Contact Load Low Power
Protection Feature Sealed
Typical Use Automotive applications
Dimensions (Approx.) Length: 6 cm, Width: 5 cm, Height: 2 cm
Weight (Approx.) 0.02 kg

3. Product Overview

The JETTING Automotive Relays are compact, black-colored units designed for robust performance in vehicle electrical systems. They come in two main configurations: 4-pin and 5-pin, each suited for different switching requirements.

JETTING 4-pin automotive relay, angled view
Figure 3.1: Angled view of a 4-pin automotive relay.
Top view of a 4-pin automotive relay
Figure 3.2: Top view of a 4-pin automotive relay.
Side view of a 4-pin automotive relay showing model 303-1AH-C-R1 U01 12VDC
Figure 3.3: Side view of a 4-pin relay (Model 303-1AH-C-R1 U01).
Bottom view of a 4-pin automotive relay with pin labels
Figure 3.4: Bottom view of a 4-pin relay, showing pin layout.
Top view of a 5-pin automotive relay
Figure 3.5: Top view of a 5-pin automotive relay.
Side view of a 5-pin automotive relay showing model 301-1C-C-R1 12VDC
Figure 3.6: Side view of a 5-pin relay (Model 301-1C-C-R1).
Bottom view of a 5-pin automotive relay with pin labels
Figure 3.7: Bottom view of a 5-pin relay, showing pin layout.

4. Setup and Installation

Before installing, ensure the vehicle's battery is disconnected to prevent electrical shorts or injury. Automotive relays typically use standard pin designations (e.g., 30, 85, 86, 87, 87a). Refer to your vehicle's wiring diagram or the specific application's requirements for correct pin connections.

4.1 Pin Configuration (Common Automotive Relays)

  • Pin 30: Power input (from battery or fused power source).
  • Pin 85: Coil ground (connected to chassis ground or control module).
  • Pin 86: Coil power (connected to a switch or control signal, typically 12V).
  • Pin 87: Normally Open (NO) output. When the coil is energized, power flows from Pin 30 to Pin 87.
  • Pin 87a (5-pin relays only): Normally Closed (NC) output. Power flows from Pin 30 to Pin 87a when the coil is de-energized. When energized, power switches to Pin 87.

4.2 Installation Steps

  1. Identify the correct location for the relay in your vehicle's electrical system.
  2. Ensure all power sources are disconnected.
  3. Connect the wires to the appropriate relay pins according to your application's wiring diagram. Use proper crimp connectors or a relay socket for secure connections.
  4. Mount the relay securely in a dry, protected location away from excessive heat or vibration.
  5. Once all connections are made and secured, reconnect the vehicle's battery.
  6. Test the circuit to ensure the relay functions as intended.

5. Operating Instructions

The automotive relay operates as an electrically controlled switch. When a 12V DC signal is applied to the coil (between pins 85 and 86), an electromagnetic field is generated, which pulls a contact arm, closing or opening the main power circuit (between pins 30 and 87/87a).

  • 4-pin Relay (NO): When the control signal is active, the relay switches power from Pin 30 to Pin 87, energizing the connected accessory. When the signal is off, the circuit between 30 and 87 opens.
  • 5-pin Relay (NO/NC): When the control signal is active, the relay switches power from Pin 30 to Pin 87 (Normally Open). When the signal is off, power flows from Pin 30 to Pin 87a (Normally Closed).

Ensure the control signal and the load current do not exceed the relay's specified voltage and current ratings (12V DC, 35A/20A) to prevent damage to the relay or connected components.

6. Maintenance

These sealed automotive relays are designed for minimal maintenance. However, periodic checks can help ensure longevity and reliable performance:

  • Visual Inspection: Periodically check the relay and its connections for any signs of corrosion, loose wires, or physical damage.
  • Cleanliness: Keep the relay and its surrounding area free from dirt, dust, and moisture.
  • Connection Integrity: Ensure all electrical connections are tight and secure. Loose connections can lead to overheating and intermittent operation.
  • Environmental Conditions: While sealed, avoid exposing the relay to extreme temperatures or direct water immersion beyond its intended automotive environment.

7. Troubleshooting

If your automotive relay is not functioning correctly, consider the following troubleshooting steps:

  • Relay Not Clicking:
    • Check if 12V DC is present at Pin 86 (coil power) when the control signal is active.
    • Verify that Pin 85 (coil ground) has a good connection to ground.
    • Inspect the relay coil for damage (though this is rare for sealed units).
  • Circuit Not Energizing (No Power Output):
    • Ensure there is constant 12V DC power at Pin 30 (power input).
    • Confirm the relay is clicking when the control signal is applied. If it clicks but no power, the internal contacts might be faulty.
    • Check the wiring from Pin 87 (or 87a) to the load for continuity and proper connection.
    • Verify the load itself is not faulty or shorted.
  • Intermittent Operation:
    • Check for loose or corroded connections at the relay pins or in the wiring harness.
    • Ensure the control signal is stable and not fluctuating.
    • The relay itself might be failing due to wear or internal damage.

If troubleshooting does not resolve the issue, consider replacing the relay with a new one of the same specifications.

8. User Tips

  • Use a Relay Socket: For easier installation and replacement, consider using a compatible relay socket. This also helps protect the relay pins from damage during wiring.
  • Fuse Protection: Always ensure the power input to Pin 30 is protected by an appropriately rated fuse to prevent damage to the circuit in case of a short.
  • Correct Pin Identification: Double-check the pin numbers on the relay and your wiring diagram. While standard, variations can occur.
  • Testing: Before final installation, you can test the relay's functionality by applying 12V to the coil pins (85 and 86) and checking for continuity between the power pins (30 and 87/87a).

9. Warranty and Support

For any questions regarding your JETTING Automotive Relay, please contact your point of purchase or the manufacturer's customer support. Keep your purchase receipt for warranty claims, if applicable. Specific warranty terms and conditions may vary by region and retailer.

© 2023 JETTING. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.