Product Overview
The diymore BMS (Battery Management System) Balance Board Series is designed to protect and manage Li-ion lithium battery packs, including 18650, 26650, and polymer batteries. These boards offer various configurations (3S, 4S, 5S) and current ratings (10A to 100A), with options for balanced or enhanced functionality. They provide essential protection features for safe charging and discharging of battery packs.

Specifications
The following table details the specifications for common models in the diymore BMS Balance Board Series:
| Feature | 3S 30A (Enhanced/Balanced) | 3S 40A (Enhanced/Balanced) | 3S 60A (Enhanced/Balanced) | 4S 40A (Enhanced/Balanced) |
|---|---|---|---|---|
| Application Scope | Ternary lithium battery with 3.7V nominal voltage, 4.2V full voltage (18650, 26650, polymer battery) | |||
| Charging Voltage | 12.6V - 13.6V | 16.8V - 18.1V | ||
| Continuous Discharge Current (Upper Limit) | 30A | 40A | 60A | 40A |
| Continuous Charge Current (Upper Limit) | 20A | 20A | 15A | 20A |
| Electric Drill Starting Current (Enhanced) | ≤ 60A (Power ≤ 130W) | ≤ 80A (Power ≤ 130W) | ≤ 120A (Power ≤ 260W) | ≤ 80A (Power ≤ 180W) |
| Electric Drill Starting Current (Balanced) | ≤ 60A (Power ≤ 130W) | ≤ 80A (Power ≤ 170W) | ≤ 120A (Power ≤ 260W) | ≤ 80A (Power ≤ 230W) |
| Product Size (Enhanced) | 41 * 55 * 3.4mm | 41 * 55 * 3.4mm | ||
| Product Size (Balanced) | 41 * 60 * 3.4mm | 41 * 62 * 3.4mm | ||
| Product Weight (Enhanced) | 8.8g | |||
| Product Weight (Balanced) | 9.8g | |||
Setup and Wiring
Careful wiring is essential for the correct and safe operation of the BMS board. Always follow the provided diagrams precisely.
General Wiring Guidelines:
- Strictly follow the wiring diagram for 0V, 4.2V, 8.4V, 12.6V (and 16.8V for 4S boards).
- Do not touch any components on the board when soldering wires to prevent accidental short circuits.
- Ensure all batteries in the pack are of the same capacity and internal resistance. Do not mix good and poor batteries.
- For 3S 60A boards, the 0V and 12.6V copper wire should be no less than 4SQMM.
Battery Requirements for Electric Drills:
- 3S 30A/40A Boards: Requires three 15C-20C power batteries or six 5C-10C power batteries to successfully start a drill. Ordinary 18650 batteries may not be sufficient.
- 3S 60A Boards: Requires three 10C-20C power batteries or six 5C-10C power batteries (recommended: SONY VTC4, VTC4A, VTC5A, VTC6). Ordinary 18650 batteries may not be sufficient.
- 4S 40A Boards: Requires three 15C-20C power batteries or eight 10C-15C power batteries to successfully start a drill. Ordinary 18650 batteries may not be sufficient.
Example Board Layouts:



Operating Instructions
Once correctly wired, the BMS board will manage the charging and discharging of your battery pack.
- Charging: Connect your charger to the designated charge terminals. The board will automatically manage the charging process within the specified voltage range (e.g., 12.6V-13.6V for 3S, 16.8V-18.1V for 4S).
- Discharging: Connect your load to the discharge terminals. The board will protect against over-discharge.
- Balancing Function: For balanced versions, the board will attempt to equalize the voltage across individual battery cells during charging. This is an auxiliary function.
- Load Current: If the heat dissipation environment is not good, reduce the load current to prevent overheating.
Maintenance
- Regularly inspect all wiring connections for looseness or corrosion.
- Ensure the BMS board is kept in a clean, dry environment, free from dust and moisture.
- Avoid exposing the board to extreme temperatures.
- For optimal performance and longevity of your battery pack, ensure all individual cells are matched in capacity and internal resistance.
Troubleshooting
- "430" Resistor Heating: When the battery is charging, it is normal for the "430" resistor to heat up, indicating the balance circuit is working.
- Excessive "430" Resistor Heating (without charging): If the "430" resistor heats severely when not charging, check for incorrect wiring.
- Drill Not Starting: If an electric drill fails to start, verify that the power batteries meet the specified C-rating requirements (e.g., 15C-20C for 3S 30A/40A boards). Ordinary 18650 batteries may not provide enough current.
- Unbalanced Battery Pack (4S boards): If using 4 groups of batteries in series and experiencing voltage drops, individually charge each battery group to ensure they are balanced before connecting in series. A faster voltage drop during discharge indicates a poor battery in that group.
- Reduced Load Current: If the BMS board or surrounding components become excessively hot, reduce the load current to prevent damage.
User Tips
- When building a battery pack, carefully select a BMS board that matches your specific series (S) and parallel (P) configuration. For example, a "3 series 7 parallel" pack requires a BMS designed for 3S.
- Be aware that some BMS boards may feature split charging and discharging ports. Ensure your power supply and load are connected to the correct terminals.
- While balancing is a feature, it may not always achieve perfect cell voltage equalization, especially with mismatched cells.
Warranty and Support
For detailed warranty information and technical support, please refer to the official product documentation. A user manual in PDF format may be available for download from the seller's website or product page.
For additional information, you may consult the User Manual (PDF).
Contact the seller or manufacturer for specific inquiries regarding your product model.