Instruction Manual

1. Introduction

This manual provides instructions for the proper installation, operation, and maintenance of your new cartridge HEPA filter, designed for compatibility with Vacmaster wet dry vacuums, specifically model VKE1030SF. This filter is essential for maintaining the performance and filtration efficiency of your vacuum cleaner for both wet and dry applications.

2. Specifications

Dimensions:

• Inner Diameter (ID): 150mm (5.91in)
• Outer Diameter (OD): 186mm (7.32in)
• Height (H): 174.4mm (6.87in)

3. Installation

Follow these steps to properly install the cartridge HEPA filter into your Vacmaster wet dry vacuum:

1. Ensure Power is Off: Before beginning, always unplug your vacuum cleaner from the power outlet to prevent accidental startup.
2. Remove Vacuum Head: Detach the vacuum head from the collection tank according to your vacuum cleaner's specific instructions.
3. Remove Old Filter (if applicable): If replacing an old filter, carefully remove it. Note how it was secured.
4. Position New Filter: Place the new cartridge HEPA filter over the filter cage in the vacuum. Ensure it sits flush and securely.
5. Secure Filter: The filter typically has a locking cap or mechanism. Align the cap with the filter and twist or press to lock it into place. Refer to the arrows on the cap for 'Open' and 'Lock' positions.

   

6. Reattach Vacuum Head: Carefully place the vacuum head back onto the collection tank and secure it with the latches.
7. Test: Plug in the vacuum and perform a brief test to ensure proper suction and operation.

4. Operating Instructions

This HEPA filter is designed for both dry and wet vacuuming tasks, providing efficient filtration for various applications.

• Dry Function: The filter effectively captures fine dust, particles, scraps of paper, chippings, and industrial waste, ensuring clean exhaust air.
• Moisture Absorption: For wet vacuuming, the filter is designed to handle moisture absorption, allowing you to clean up spills, suck water, and manage other liquid messes without damaging the vacuum motor.

Always ensure the filter is correctly installed before operating your vacuum cleaner to prevent damage and maintain optimal performance.

5. Maintenance

Regular maintenance of your HEPA filter is crucial for extending its lifespan and ensuring your vacuum operates at peak efficiency.

Cleaning the Filter:

1. Remove Filter: Unplug the vacuum and remove the filter as described in the installation section.
2. Tap Clean: Gently tap the filter against a hard surface to dislodge loose dirt and debris.
3. Rinse (if applicable): As this is a PTFE cartridge filter, it may be washable. Rinse the filter under running water from the clean side (inside-out) until the water runs clear. Do not use hot water or harsh detergents.
4. Dry Completely: Allow the filter to air dry completely for at least 24 hours before reinstallation. Do not use heat to dry the filter, as this can damage the material.
5. Inspect: Before reinstalling, inspect the filter for any tears or damage. Replace if damaged.

Filter Replacement:

The lifespan of your filter depends on usage frequency and the type of debris collected. Replace the filter when you notice a significant decrease in suction power, even after cleaning, or if the filter shows signs of wear and tear (e.g., holes, excessive discoloration that cannot be cleaned).

6. Troubleshooting

If you encounter issues with your vacuum cleaner's performance after installing the new filter, consider the following:

• Reduced Suction:
  • Ensure the filter is clean and not clogged.
  • Verify the filter is correctly seated and the locking cap is securely fastened.
  • Check for any blockages in the hose or attachments of the vacuum.
• Dust Escaping:
  • Confirm the filter is properly installed and sealed.
  • Inspect the filter for any damage or tears that might allow dust to pass through.

If problems persist, consult your Vacmaster vacuum cleaner's main instruction manual or contact customer support.

7. User Tips

• For optimal performance, clean your filter regularly, especially after heavy use or vacuuming fine dust.
• When switching between wet and dry vacuuming, it's good practice to inspect and clean the filter to prevent cross-contamination and maintain efficiency.
• Always have a spare filter on hand to minimize downtime during cleaning or replacement.

8. Warranty and Support

For any questions regarding the compatibility or performance of this filter, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.