EDM Industrial Floor Fan 30 Cm

Contents

EDM Industrial Floor Fan 30 Cm User Manual

Model: Industrial Floor Fan 30 Cm

Product Overview

This manual provides instructions for the safe and efficient use of your EDM Industrial Floor Fan. Please read this manual thoroughly before operating the fan and retain it for future reference.

EDM Industrial Black Floor Fan with 30 cm blades

Figure 1: EDM Industrial Black Floor Fan

The EDM Industrial Floor Fan is designed to provide powerful airflow for various environments. It features a robust construction, adjustable tilt, and multiple speed settings to suit your ventilation needs.

Safety Instructions

  • Always unplug the fan from the power outlet before cleaning, servicing, or moving it.
  • Do not insert fingers or any other objects through the grille when the fan is operating.
  • Ensure the fan is placed on a stable, level surface to prevent it from tipping over.
  • Do not operate the fan with a damaged cord or plug. If the cord or plug is damaged, contact qualified service personnel.
  • Keep the fan away from water or other liquids. Do not use it in wet or damp environments.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.

Setup

Unpacking

  1. Carefully remove the fan from its packaging.
  2. Check for any signs of damage during transit. If damage is found, do not operate the fan and contact the seller.
  3. Ensure all components are present. The fan typically comes pre-assembled with its stand.

Placement

  • Place the fan on a firm, level surface.
  • Ensure there is adequate space around the fan for proper air circulation. Do not block the air intake or exhaust.
  • Position the fan away from curtains, drapes, or any objects that could be drawn into the fan blades.
  • Connect the power cord to a suitable electrical outlet (220/240V, 50Hz).

Operating Instructions

  1. Power On/Off: Plug the fan into a grounded electrical outlet. Locate the control knob or buttons, usually on the rear or side of the fan. Turn the knob to the 'ON' position or press the power button.
  2. Adjusting Airflow Speed: This fan offers 3 air flow rates. Rotate the control knob or press the speed buttons to select your desired speed (e.g., Low, Medium, High).
  3. Adjusting Fan Angle: The fan head can be tilted to direct airflow. Loosen the adjustment knobs on either side of the fan frame, tilt the fan head to the desired angle, and then securely tighten the knobs.
  4. Power Off: To turn off the fan, rotate the control knob to the 'OFF' position or press the power button. Unplug the fan from the outlet when not in use for extended periods.

Maintenance

Cleaning

  • Always unplug the fan before cleaning.
  • Use a soft, damp cloth to wipe the exterior surfaces of the fan. Do not use abrasive cleaners or solvents.
  • To clean the fan blades and grilles, you may need to remove the front grille. Refer to the diagram (if available) or gently unclip the grille. Carefully wipe the blades and grilles with a damp cloth. Ensure all parts are completely dry before reassembling and operating the fan.
  • Do not immerse the fan in water or allow water to drip into the motor housing.

Storage

  • When not in use, store the fan in a cool, dry place.
  • If possible, store it in its original packaging to protect it from dust and damage.

Troubleshooting

ProblemPossible CauseSolution
Fan does not turn on.Not plugged in; power outlet not working; fan switch off; damaged power cord.Ensure fan is securely plugged in. Test outlet with another device. Turn fan switch to 'ON'. Inspect power cord for damage; if damaged, do not use.
Low airflow.Fan speed set too low; grilles blocked; dirty blades.Increase fan speed. Ensure nothing is obstructing the grilles. Clean fan blades and grilles as per maintenance instructions.
Unusual noise.Loose parts; fan not on a level surface; foreign object in fan.Check for any loose screws or components. Place fan on a stable, level surface. Unplug fan and carefully inspect for any foreign objects.

If you encounter a problem not listed here or if the issue persists after attempting the solutions, please contact customer support.

Specifications

FeatureDetail
ModelIndustrial Floor Fan 30 Cm
BrandEDM
Power45W
Blade Diameter30 cm
Air Flow Rates3 speeds
Air Flow Volume1860 m³/h
Voltage/Frequency220/240V - 50Hz
Number of Blades3
ColorBlack
Package Dimensions (L x W x H)20 cm x 20 cm x 10 cm
Package Weight3.3 kg

User Tips

  • For optimal cooling, position the fan to create a cross-breeze by placing it opposite a window or door.
  • Use the lower speed settings for quieter operation and energy saving when maximum airflow is not required.
  • Regularly check and clean the fan grilles to prevent dust buildup, which can reduce efficiency and potentially cause overheating.

Warranty and Support

This product is covered by a standard manufacturer's warranty. For specific warranty terms, duration, or to obtain support, please contact the seller directly. Keep your purchase receipt as proof of purchase.

Seller: FERRETERIA TERRADO Store

For any inquiries or technical assistance, please reach out to the seller through the platform where the purchase was made.

© 2023 EDM. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.