Beitian BE-180

Contents

BEITIAN BE-180 GPS Module User Manual

GLONASS Dual GNSS UART TTL Level GPS Module

1. Introduction

The BEITIAN BE-180 is a compact and high-performance GPS module designed for various applications, particularly RC drones and flight controllers such as F3, F4, and F7. It supports multiple Global Navigation Satellite Systems (GNSS) including GPS, BDS, and GALILEO, providing accurate positioning data via a UART TTL interface.

Front and back view of the Beitian BE-180 GPS module

Figure 1: Front and back view of the BEITIAN BE-180 GPS Module.

2. Setup

2.1 Package Contents

  • BEITIAN BE-180 GPS Module

2.2 Pin Description

The BE-180 module features a 4-pin connector for power and data communication. Ensure correct polarity and connection to avoid damage.

Pin description diagram and table for the BE-180 module

Figure 2: BE-180 Pinout Diagram and Description.

PINNameI/ODescription
1GNDGGround
2TXOSerial Data Output
3RXISerial Data Input
4VCCIDC 3.6V - 5.5V supply input, Typical: 5.0V

2.3 Initial Power-Up and Indicator Lights

Upon powering the module, observe the indicator lights for operational status:

  • Blue Light (TX LED): Flashes when power is on, indicating that there is serial data output.
  • Red Light (PPS LED): Does not light up if the module is not positioned (no GPS fix). After achieving 3D positioning, it starts to flash, indicating a valid GPS fix and Pulse Per Second output.

3. Operating Instructions

3.1 GNSS Modes and Frequency

The BE-180 module operates with multiple GNSS constellations for enhanced accuracy and reliability:

  • Modes: GPS + BDS + GALILEO
  • Frequency: GPS L1 C/A, QZSS L1 C/A/S, BDS B1I/B1C, GALILEO E1B/C, SBAS L1 C/A (WAAS, EGNOS, MSAS, GAGAN)

3.2 Data Output

The module outputs positioning data via its UART (Universal Asynchronous Receiver/Transmitter) interface at TTL level.

  • Baud Rate: Configurable from 4800bps to 921600bps. The default baud rate is 38400bps.
  • Protocol: NMEA, UBX
  • NMEA Messages: RMC, VTG, GGA, GSA, GSV, GLL
  • Update Rate: Configurable from 0.25Hz to 18Hz. The default update rate is 1Hz.
  • FLASH: The module includes FLASH memory, allowing configuration changes to be saved even after power loss.
  • Time Pulse Signal (PPS): Configurable from 0.25 Hz to 10 MHz. The default period is 1 second, with the high level lasting for 100ms.

3.3 Integration with Flight Controllers

When integrating with RC drone flight controllers (F3, F4, F7), connect the module's TX to the flight controller's RX, and the module's RX to the flight controller's TX. Ensure the flight controller's UART port is configured to the correct baud rate and GPS protocol (e.g., NMEA or UBLOX) in its firmware settings (e.g., Betaflight, iNav).

4. Maintenance

  • Operating Temperature: Ensure the module operates within -40°C to +85°C.
  • Storage Temperature: Store the module within -40°C to +105°C.
  • Cleaning: Keep the module free from dust and moisture. Use a soft, dry cloth for cleaning if necessary.
  • Handling: Handle the module with care to avoid physical damage to the PCB or antenna.

5. Troubleshooting

5.1 No Data Output (TX LED not flashing)

  • Check power supply (VCC and GND) for correct voltage (3.6V-5.5V) and secure connection.
  • Verify the module is correctly wired to the receiving device (TX to RX, RX to TX).
  • Ensure the receiving device's UART port is enabled and configured correctly.

5.2 No GPS Fix (PPS LED not flashing)

  • Ensure the module has a clear view of the sky, free from obstructions.
  • Allow sufficient time for a cold start (up to 27 seconds).
  • Verify the module is receiving adequate power.
  • Check for potential sources of electromagnetic interference near the module.

5.3 Incorrect Data or No Communication

  • Confirm the baud rate settings on both the GPS module (if configured) and the receiving device match.
  • Check for proper ground connection between the module and the receiving device.
  • Ensure the correct GPS protocol (NMEA/UBX) is selected on the receiving device.

6. Specifications

Detailed specifications table for BE-180 GPS module

Figure 3: Comprehensive Specifications for BEITIAN BE-180 GPS Module.

6.1 General Parameters

ParameterValue
ModelBE-180
GNSS ModesGPS+BDS+GALILEO
Receiver TypeGPS L1 C/A, QZSS L1 C/A/S, BDS B1I/B1C, Galileo E1B/C, SBAS L1 C/A
Default Position SystemGPS, BDS, GALILEO
Augmentation SystemSBAS, QZSS
ProtocolNMEA, UBX
LevelTTL level

6.2 Electrical Characteristics

ParameterValue
VoltageDC 3.6V-5.5V (Typical: 5.0V)
Current Consumption15mA/5.0V
Baud Rate4800bps - 921600bps (Default: 38400bps)
Update Rate0.25Hz - 18Hz (Default: 1Hz)
Time Pulse Signal0.25 Hz to 10 MHz (Default: 1s period, 100ms high)

6.3 Performance Specifications

ParameterValue
Tracking & Navigation Sensitivity-166dBm
Reacquisition Sensitivity-160dBm
Cold Start Sensitivity-148dBm
Hot Start Sensitivity-160dBm
Horizontal Position Accuracy2.0m CEP
Velocity Accuracy0.05m/s
Dynamic Heading Accuracy0.3 deg
Time Pulse AccuracyRMS 30ns, 99% 60ns
Cold Start Acquisition27s
Hot Start Acquisition1s
Aided Start Acquisition1s
Altitude Limit80,000m
Velocity Limit500m/s
Dynamics Limit<4g

6.4 Physical Specifications

ParameterValue
Dimension18mm x 18mm x 6.1mm
Weight4.9g
Connector1.00mm 4pins connector
Operating Temperature-40°C ~ +85°C
Storage Temperature-40°C ~ +105°C

7. User Tips

  • Clear Sky View: For optimal performance and quick GPS lock, ensure the module has an unobstructed view of the sky.
  • Firmware Configuration: When using with flight controllers, correctly configure the UART port, baud rate, and GPS protocol (e.g., UBLOX or NMEA) in your flight controller's firmware (e.g., Betaflight, iNav).
  • RTH Setup: Features like Return-To-Home (RTH) are typically configured within the flight controller's firmware and require proper calibration and setup of the GPS module within that system. Refer to your flight controller's specific documentation for detailed RTH setup instructions.
  • Interference: Keep the GPS module away from high-current wires, video transmitters, and other potential sources of electromagnetic interference to maintain signal integrity.

8. Warranty and Support

Please refer to your point of purchase for specific warranty terms and conditions. For technical support, contact the manufacturer or your retailer.

© 2023 BEITIAN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.