1. Introduction
This manual provides essential information for the installation, operation, and maintenance of the Ananda EF1 Controller, designed as a replacement main board for the Xiaomi QiCycle EF1 Electric Folding Bike. The controller is a critical component responsible for managing the electric motor's power, speed, and overall communication within the e-scooter's electrical system.
2. Safety Information
⚠️️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage of your electric bike. This controller is an electrical component; improper installation or handling can lead to electric shock, fire, or damage to the device and the scooter.
- Always disconnect the scooter's battery power before attempting any installation or maintenance.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Professional installation by a qualified technician is highly recommended.
- Keep the controller dry and away from moisture.
- Do not attempt to open or modify the controller casing, as this may void any implied warranty and pose safety risks.
3. Specifications
| Feature | Detail |
|---|---|
| Brand | Ananda |
| Model Number | EF1 Controller (Variants: 3610DSC-N2A0, 3610DSC-N2B0) |
| Type | Controller |
| Voltage | 36V |
| Compatibility | For Xiaomi QiCycle EF1 Electric scooter, For Mijia Bicycle |
| Origin | Mainland China |
| Dimensions (Approx.) | 10cm (Length) x 10cm (Width) x 10cm (Height) |
| Weight (Approx.) | 0.1 kg |
4. Package Contents
The package typically includes:
- 1 x Ananda EF1 Controller
5. Setup and Installation
Note: Due to the electrical nature of this component, professional installation is strongly recommended. Incorrect installation can damage the controller, the scooter, or cause personal injury.
- Preparation: Ensure the electric bike is turned off and the battery is disconnected.
- Locate Existing Controller: Identify the location of the existing controller on your Xiaomi QiCycle EF1. This is typically housed in a protective compartment.
- Disconnect Old Controller: Carefully disconnect all wiring harnesses and connectors from the old controller. Pay close attention to the orientation and type of each connector.
- Install New Controller: Position the new Ananda EF1 Controller in the designated compartment.
- Connect Wiring: Connect the wiring harnesses from the scooter to the new controller. Ensure that all connectors are firmly seated and match the pin configurations. Refer to the images below for visual identification of the controller and its connectors.
- Secure Controller: Secure the controller within its compartment using appropriate fasteners.
- Reconnect Battery & Test: Reconnect the scooter's battery and perform a functional test to ensure all systems (motor, display, throttle) are operating correctly.



6. Operating Instructions
The Ananda EF1 Controller functions as the 'brain' of your electric folding bike. Once correctly installed, its operation is integrated with the scooter's existing controls (throttle, brake, display). It translates your inputs into commands for the motor, manages power distribution, and monitors various system parameters. There are no direct user controls on the controller itself; its function is to enable the normal operation of your Xiaomi QiCycle EF1 electric bike.
7. Maintenance
- Keep Clean and Dry: Regularly inspect the controller area for dirt, dust, or moisture. Keep the controller and its connections clean and dry to prevent corrosion and electrical issues.
- Check Connections: Periodically check all wiring connections to ensure they are secure and free from damage. Loose connections can lead to intermittent operation or component failure.
- Avoid Physical Damage: Protect the controller from impacts or excessive vibrations, which can damage internal components.
- Temperature: Avoid exposing the controller to extreme temperatures for prolonged periods.
8. Troubleshooting
If you experience issues with your electric bike after installing the new controller, consider the following:
- Scooter Not Powering On:
- Check all power connections from the battery to the controller. Ensure the battery is charged and properly connected.
- Verify the main power switch on the scooter is in the 'ON' position. - Motor Not Responding / Erratic Behavior:
- Recheck all signal and motor phase wire connections to the controller. Ensure they are correctly matched and secure.
- Inspect for any visible damage to the wiring or connectors. - Display Issues:
- Ensure the display unit is properly connected to the controller. - Compatibility:
- Verify that the controller model (e.g., 3610DSC-N2A0 or 3610DSC-N2B0) and its connector pin configuration (e.g., 6-pin) are compatible with your specific Xiaomi QiCycle EF1 model. Incompatibility can lead to non-functionality.
If problems persist, consult a professional electric bike technician.
9. User Tips
- Verify Pin Configuration: Before purchasing or installing, always confirm the exact pin configuration of your existing controller's connectors, especially for multi-pin data cables (e.g., 6-pin European controller), to ensure compatibility with the replacement unit.
- Component Specificity: Remember that this product is specifically the EF1 Controller. If you require other parts for your Xiaomi QiCycle EF1, ensure you purchase them separately.
10. Warranty and Support
For any issues, technical support, or warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase. Specific warranty terms and conditions may vary by region and seller.