LEHX Pro Car Multimedia Player

Contents

LEHX Pro Car Multimedia Player User Manual

Model: LEHX Pro 2 din Android 14 Car Radio Multimedia Video Player

Compatible with Renault Duster 1 (2010-2015) and Nissan Terrano (2014-2020)

1. Introduction

Thank you for choosing the LEHX Pro Car Multimedia Player. This manual provides essential information for the proper installation, operation, and maintenance of your new device. Please read it thoroughly before use.

This device offers advanced features including Android 14 operating system, Carplay, Android Auto, GPS Navigation, and a built-in DSP for enhanced audio quality. It is designed to seamlessly integrate into your vehicle's dashboard.

LEHX Pro Car Multimedia Player installed in a car dashboard

Image: LEHX Pro Car Multimedia Player installed in a car dashboard, showing the main unit and compatible car frame.

2. Setup and Installation

2.1. Before Installation

Before proceeding with the full installation in your car, it is highly recommended to test the unit. Due to potential impacts during transit, the product may be affected. Please connect the unit to a 12V power source and verify basic functionality before mounting it in the vehicle.

2.2. Rear Interface Description and Wiring

Carefully identify each port and wire according to the diagram below. Incorrect wiring can damage the unit or vehicle electronics.

Rear Interface Wiring Diagram

Image: Detailed rear interface wiring diagram for the LEHX Pro Car Multimedia Player.

Power Plug Connections:

  • Yellow (BATTERY): Connect to constant +12V power supply. This maintains power and memory function.
  • Red (ACC): Connect to ignition switch +12V. This powers the unit on/off with the car's ignition.
  • Black (GND): Connect to ground wire.
  • Orange (ILLUMINATION): Connect to backlight illumination.
  • Pink (REVERSE): Connect to the reversing camera control line.
  • Brown (KEY2) & Orange/black striped (KEY1): Connect to steering wheel control wires.
  • Blue (ANT): Connect to auto antenna power.

Audio/Video Connections:

  • F-CAM (VIDEO-IN-2): Front Camera Input.
  • AUX R IN / AUX L IN: Right and Left Audio Input.
  • VIDEO-IN-1 / VIDEO OUT: Video Input 1 / Video Output.
  • FR OUT / FL OUT: Front Right / Front Left Audio Output.
  • SUB WOOF: Subwoofer Output.
  • MIC: Microphone Input.
  • AMP CONT: Amplifier Control.

Important Note on Speaker Wires: There are 8 speaker cables. Each cable must not be grounded, shared, or touch other lines. Doing so may result in no sound output, distorted sound, or overheating of the unit.

2.3. CANBUS Connection

If your vehicle requires a CANBUS connection, follow the instructions below. The CANBUS box is used to integrate the car's original functions with the multimedia player.

CANBUS Connection Diagram

Image: CANBUS connection diagram for high-end and low-end car models.

  • For High-End Model Car: Disconnect the CANBUS box and then connect it.
  • For Low-End Model Car: Connect the CANBUS box and then disconnect it.

Attention: If the CANBUS box and black buckle are connected simultaneously, it may cause the radio to fail to shut down after the car is turned off.

2.4. Reversing Camera Installation

To install the reversing camera, follow these steps:

Reversing Camera Installation Diagram

Image: Reversing camera wiring and installation diagram.

  1. Yellow cable: Connect to the navigation reversing video input socket.
  2. Red cable: Connect to the reverse detection line of the navigation adapter (BACK or REVERSE).
  3. Connect the camera's positive power wire (usually red) to the positive pole of the reverse light power supply.
  4. Connect the camera's negative power wire (usually black) to the body screw (ground) or the negative pole of the reverse light power supply.

If the reversing camera is not installed, do not connect the REVERSE/BACK cable to any place. Leave it unconnected. Otherwise, the unit may not display properly or may automatically enter reverse mode, potentially causing malfunction. If this occurs, disconnect the REVERSE/BACK line as soon as possible.

3. Operation

3.1. Learning Steering Wheel Controls

To program your steering wheel controls:

  1. Press and hold a button on your original car's steering wheel.
  2. On the multimedia player's screen, find the corresponding button icon for the function you want to assign.
  3. Click the icon to change its color. Successful learning is indicated by the color change.

3.2. Apple CarPlay / Android Auto

This feature allows seamless integration with your smartphone for navigation, music, and more. Note that Google Play services may need to be available locally for Android Auto.

CarPlay and Android Auto Interface

Image: CarPlay and Android Auto user interfaces displayed on the unit.

Wired Connection:

Simply connect your USB data cable to the unit, and it will automatically enter the CarPlay or Android Auto interface.

Wireless Connection:

  1. First, enable Bluetooth and Wi-Fi functions on your mobile phone.
  2. Connect to the unit's Bluetooth.
  3. The unit will automatically enter the CarPlay or Android Auto interface. (Note: The signal is transmitted via Wi-Fi. Even if Bluetooth is turned off, it will transmit normally. If Wi-Fi is turned off, CarPlay/Android Auto will disconnect.)

Requirements for Android Auto: A mobile phone with Android 6.0 or higher and a valid data cable connection are required.

3.3. Voice Control

The unit supports voice commands for various functions, providing a convenient and safe driving experience.

Voice Control Commands

Image: Examples of voice commands for navigation, radio, Bluetooth, and music control.

3.4. Split Screen Functionality

You can use two applications simultaneously on the screen, such as navigation and music playback.

Split Screen Display

Image: Examples of split-screen usage, showing maps with DVR, and maps with music.

3.5. Adjustable Button Colors

Customize the color of the unit's physical buttons to match your car's interior lighting or personal preference.

Adjustable Button Colors

Image: Interface for adjusting button light colors (Red, Orange, White, Green, Blue, Cyan-blue, Purple).

3.6. Bluetooth Functionality

The unit features Bluetooth 5.1/5.3 for hands-free calling and audio streaming.

Bluetooth 5.1 Feature

Image: Bluetooth 5.1 feature highlighting mobile phone pairing, music playback, and hands-free dialing.

To use Bluetooth:

  1. Turn on the unit and enable Bluetooth on your mobile phone.
  2. Search for the unit's Bluetooth name on your phone and click 'Connect'.
  3. Once connected, you can answer calls and play music via Bluetooth.

3.7. GPS Navigation

The unit comes with pre-installed offline maps and supports permanent free updates. It is compatible with various navigation applications.

GPS Navigation Interface

Image: GPS Navigation interface showing support for Waze, Navitel, Yandex, and Igo.

3.8. DAB+ Tuner (Optional)

Enjoy high-quality digital audio broadcasting with the optional DAB+ radio receiver stick, connecting via USB.

DAB+ Tuner Ready

Image: DAB+ Tuner Ready feature, showing the optional DAB+ radio receiver stick connected via USB.

4. Maintenance

To ensure the longevity and optimal performance of your LEHX Pro Car Multimedia Player, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the screen and exterior. Avoid abrasive cleaners or solvents.
  • Temperature: Avoid exposing the unit to extreme temperatures, both hot and cold, for extended periods.
  • Software Updates: Periodically check for software updates to improve performance and add new features. Note that functions may change without prior notice with updates.
  • USB Devices: Ensure USB flash drives are formatted to FAT32 for optimal compatibility.

5. Troubleshooting

This section addresses common issues and provides solutions.

5.1. Cannot Boot Normally

  1. Wiring Check: Ensure the yellow (B+), red (ACC), and black (GND) wires are correctly connected. Yellow to constant +12V, red to ignition +12V, black to ground. Incorrect or incomplete connections will prevent booting.
  2. Fuse Check: If the 3 wires are connected correctly but the unit doesn't boot, check the fuse on the yellow wire. If the fuse is intact, twist the yellow and red wires together, turn on the ignition, and press the power button to test.
  3. Original Car Wiring: If the original car wiring colors do not match standard, connecting directly may cause damage. Do not plug the original car plug directly into the new unit if it's not designed for it.
  4. Persistent Fuse Blowing: If the fuse blows repeatedly, it indicates a short circuit in the unit's protection circuit. Professional service is required.

5.2. Automatic Shut-down

  1. Cable Error: If the blue cable (automatic antenna power supply) is connected to the unit's power cable, automatic shutdown may occur. Correct the wiring.
  2. Unstable Voltage: Test the power supply with a stable 12V-5A source. If the unit still shuts down automatically, the power supply or the unit itself may be faulty.

5.3. Noise Issues

  1. Speaker Power: If the original speaker power is too low, noise may occur when the volume is high. Keep the volume at a moderate level.
  2. Grounded Speaker Cable: Ensure no speaker cables are grounded. Connect the speaker cable directly to the unit's speaker cable.

5.4. Remote Control Not Working

Test the remote control by pointing it at your mobile phone camera and pressing a button. If the phone's screen lights up, the remote control has power. If not, replace the battery.

5.5. Settings Not Saved (No Memory)

  1. Ensure the yellow and red wires are connected together (yellow to positive, red to key control).
  2. If yellow and red are reversed, simply swap their positions.

5.6. Bluetooth Not Working

Turn on the unit, search for its Bluetooth name on your mobile phone, and connect. If issues persist, ensure the unit's Bluetooth is enabled and try re-pairing.

5.7. Product Emits Smoke

Replace the FUSE. If the problem persists, the internal circuit is burned. After-sales service is required.

5.8. Sound Cannot Be Adjusted

  1. Reset the unit or unplug and replug the power cord.
  2. If the volume knob is broken, it may need replacement.

5.9. Reversing Camera Not Displaying

  1. Wiring: Check for incorrect or missing wiring. Refer to the installation method.
  2. Camera Fault: If the camera's light does not illuminate when properly wired, the camera may be faulty and require replacement.

5.10. USB Devices Cannot Be Played

Format the USB flash drive to FAT32. Re-download music or files and try again. If it still doesn't work, replace the USB flash drive.

5.11. FM Does Not Receive Radio Stations

  1. Antenna Connection: Ensure the antenna plug is fully inserted. Check if the antenna is disconnected or the line is faulty.
  2. Station Search: Use the 'AS' button for automatic search or manually search using the 'before' or 'after' buttons.
  3. If the above steps don't resolve the issue, unplug the antenna plug and insert a screwdriver or metal strip into the antenna port as a temporary antenna to test.

5.12. No Sound Immediately After Installation

The unit is tested before shipment. If there's no sound, it's usually a wiring error or a short-circuited original car speaker wire.

  1. Check if the speaker cable is short-circuited and connected. Reconnect if necessary.
  2. Verify the number of speaker cables. If only 2 speaker cables are present, and the original car line does not match the unit, you may need to re-route the original car line. Each speaker requires 2 wires; 2 speakers require 4 wires.

5.13. No Sound After A While

Disconnect all speaker cables from the unit (do not remove them). Find an external speaker and connect it to the gray and purple wires of the unit's tail line. Connect any green group and check for sound. If there is sound, the car's speaker line is short-circuited or the speaker is damaged. If there is no sound, the unit is broken.

6. Specifications

The LEHX Pro Car Multimedia Player comes in various configurations. Please refer to the specific model variant for exact specifications.

General Specifications
Feature Specification
Brand NameLEHX
Operating SystemAndroid
DinDouble Din
Display Size9"
ResolutionQLED 1280*720
Out Power50x4
Voltage12 V
Item Weight1.7kg
Item Size255mm-151mm
Max External Memory128G
Digital Media FormatCD, DVD-R/RW, DVD-RAM, VIDEO CD, Mp3, MP4, WMA, JPEG
OSD LanguageMulti-language support (including English, Spanish, Russian, French, German, etc.)
CertificationCE
MaterialABS+
Is touch screenYes
Built-in ScreenYes
Warranty1 year
Model Variant Specifications
Model CPU RAM/ROM Connectivity Special Features
LQUIS8141 4 Core1GB RAM / 32GB ROMWIFI 2.4G, Bluetooth 5.0ASP, 2*USB ports
L6XUIS8141 4 Core2GB RAM / 32/64GB ROMWIFI 2.4G, Bluetooth 5.0ASP, 2*USB ports, Wireless Carplay + Android AUTO
L6 Plus9863/UIS8581 64BIT 8 Core2GB RAM / 32GB ROMWIFI 5G, Bluetooth 5.3HIFI DSP, 2*USB ports
L7 Plus9863/UIS8581 64BIT 8 Core2/4GB RAM / 32/64GB ROM4G LTE, WIFI 5G, Bluetooth 5.3ASP, 2*USB ports, Wireless Carplay + Android AUTO
L5 Pro9863/UIS8581 64BIT 8 Core2/4GB RAM / 32/64GB ROM4G LTE, WIFI 5G, Bluetooth 5.3HIFI DSP, 2*USB ports, Wireless Carplay + Android AUTO
L6 Pro7862 64BIT 8 Core4/6GB RAM / 32/64/128GB ROM4G LTE, WIFI 5G, Bluetooth 5.3HIFI DSP, 3*USB ports, Wireless Carplay + Android AUTO

7. Warranty and Support

7.1. Warranty

The LEHX Pro Car Multimedia Player comes with a 1-year warranty from the date of purchase, covering manufacturing defects.

7.2. Customer Support

For any technical assistance, questions, or issues not covered in this manual, please contact LEHX customer service. Our professional technical team is available to provide free technical services.

You can also refer to the official user manual PDF for more detailed information: View User Manual (PDF)

LEHX Qualification Certificates

Image: LEHX Qualification Certificates (FCC, CE, RoHS, ISO14001).

LEHX Factory Overview

Image: LEHX Factory Overview, showing design, production, testing, detection, and packaging processes.

8. User Tips

  • Professional Installation: It is highly recommended to have the unit installed by professionals to avoid any damage to your car's dashboard or the device itself.
  • Steering Wheel Control Setup: If your order includes a CANBUS, ensure you set the correct CANBUS type in the unit's settings for the steering wheel buttons to function properly. If not, use the manual learning method: Settings > Car Information > SWC > Click 'Clear All' > Then click the icon on screen > Press the corresponding button on your steering wheel.
  • Boot Logo Customization: You can change the boot logo by navigating to Configuration > Car Information > General > Boot Logo. Use password '8888' for L6/L6Plus models or '3368' for L6Pro models, then select your desired logo.
  • Sound Quality: Users have noted that the sound quality is generally good, but ensure proper wiring and speaker connections for optimal performance.
  • Frame Compatibility: For Nissan Terrano 3 (2021 model), the frame may require minor modifications to fit perfectly.
  • Dual Camera Use: The unit supports the use of two cameras (front and rear).
  • AUX Input: The unit includes an AUX input for external audio sources.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.