ThinkRider C5

Contents

ThinkRider C5 Speed & Cadence Sensor User Manual

Model: C5 | Brand: ThinkRider

1. Introduction

The ThinkRider C5 is a versatile dual-mode speed and cadence sensor designed for cyclists. It provides accurate speed and cadence data for various cycling activities, including road biking and mountain biking. The sensor supports both ANT+ and Bluetooth Low Energy (BLE) communication protocols, ensuring broad compatibility with cycling computers, smartphones, bike trainers, and sports watches from brands like Garmin and Bryton.

This manual provides detailed instructions on how to set up, operate, and maintain your C5 sensor.

ThinkRider C5 Speed and Cadence Sensor
ThinkRider C5 Speed and Cadence Sensor

2. Package Contents

Please check the box for the following items:

  • Speed Cadence Sensor x 1
  • CR2032 Battery x 1 (pre-installed, with insulation sheet)
  • Rubber Mat (flat) x 1
  • Rubber Mat (curved) x 1
  • Small Rubber Elastic Ring x 6
  • User Manual x 1
Diagram of ThinkRider C5 package contents including sensor, rubber mats, elastic rings, and user manual.
Product Accessories: Sensor, rubber mats, elastic rings, and user manual.

3. Specifications

FeatureDetail
BrandThinkRider
ModelC5 Speed & Cadence Dual Sensor
Dimensions33 * 29.7 * 9.2 mm
Weight8.1g
BatteryCR2032 220mAh
Battery LifeApprox. 300 hours (both speed and cadence modes)
Waterproof RatingIP67
Working Temperature-10℃ ~ 50℃
Communication ProtocolsANT+ & BLE (Bluetooth Low Energy)
Measurement Extremum (Speed)120 km/h
Measurement Extremum (Cadence)300 rpm
Outer Case MaterialABS
ColorBlack
ThinkRider C5 product information table with specifications
Detailed product specifications for the C5 sensor.

4. Setup Guide

4.1 Initial Battery Activation

  1. Turn the battery compartment gasket in the "open" direction to open it.
  2. Remove the insulation sheet from the battery compartment.
  3. Rotate the battery compartment gasket back to close it securely.
Video demonstrating the initial battery activation and mode switching process.

4.2 Switching Between Speed and Cadence Modes

The C5 sensor operates in two modes: Speed Mode (indicated by a Red light flash) and Cadence Mode (indicated by a Blue light flash). To switch between modes:

  1. Open the battery compartment.
  2. Remove the CR2032 battery.
  3. Reinsert the battery. The sensor will flash either red or blue to indicate the current mode.
  4. Close the battery compartment.
Diagram showing the sensor in speed mode (red light) and cadence mode (blue light) after battery reinstallation.
Visual guide for switching between Speed Mode (Red light) and Cadence Mode (Blue light).

4.3 Installation for Speed Mode

  1. Select the curved rubber mat.
  2. Buckle the curved rubber mat onto the back of the sensor.
  3. Bind the sensor with the large rubber band onto the wheel axle (front or rear wheel hub).
  4. Ensure the sensor is securely attached and does not interfere with wheel rotation.
Four-step diagram showing installation of the speed sensor on a bicycle wheel hub using a curved rubber mat and elastic band.
Installation steps for the speed sensor on the wheel axle.

4.4 Installation for Cadence Mode

  1. Select the flat rubber mat.
  2. Buckle the flat rubber mat onto the back of the sensor.
  3. Bind the sensor with the small rubber band onto the pedal crank.
  4. Ensure the sensor is securely attached and does not interfere with pedaling.
Diagram showing installation of the cadence sensor on a bicycle pedal crank using a flat rubber mat and elastic band.
Installation steps for the cadence sensor on the pedal crank.

5. Operating Instructions

5.1 Pairing with Cycling Computer or App

Once the sensor is installed and in the desired mode (Speed or Cadence):

  1. For Speed Mode: Spin the wheel to activate the sensor (red light will flash).
  2. For Cadence Mode: Rotate the pedal crank to activate the sensor (blue light will flash).
  3. On your cycling computer, smartphone app (e.g., PowerFun, Wahoo Fitness, Bryton, Garmin, XOSS), bike trainer, or sports watch, search for new ANT+ or Bluetooth devices.
  4. Select the ThinkRider C5 sensor from the list of available devices to pair.
ThinkRider C5 sensor showing compatibility with various cycling software and devices like computers, phones, bike trainers, and sports watches.
The C5 sensor supports ANT+ and Bluetooth for wide compatibility.

5.2 Important Note for Speed Mode

In speed mode, it is crucial to set the correct wheel diameter in your cycling computer or app to ensure accurate speed data. Refer to your cycling computer/app's manual for instructions on how to configure wheel diameter.

6. Maintenance

6.1 Cleaning

Wipe the sensor with a soft, damp cloth to remove dirt and debris. Do not use harsh chemicals or abrasive cleaners, as these may damage the device.

6.2 Battery Replacement

The sensor uses a CR2032 battery. When the battery is low, the sensor's performance may degrade or it may stop transmitting data. To replace the battery:

  1. Open the battery compartment by turning the gasket in the "open" direction.
  2. Remove the old CR2032 battery.
  3. Insert a new CR2032 battery with the positive (+) side facing up.
  4. Close the battery compartment securely.

The battery life is approximately 300 hours of continuous use. If riding one hour a day, it can last about 300 days.

Image of a CR2032 battery, highlighting the low power consumption of the sensor.
The sensor uses a standard CR2032 coin cell battery for long endurance.

6.3 Waterproofing

The ThinkRider C5 sensor is IP67 waterproof, meaning it is protected against dust and can withstand immersion in water up to 1 meter for 30 minutes. However, it is not designed for prolonged underwater use. Ensure the battery compartment is securely closed to maintain its waterproof integrity.

ThinkRider C5 sensor installed on a bicycle wheel, showing its IP67 waterproof capability in a wet environment.
IP67 waterproof rating ensures protection against rain and splashes.

7. Troubleshooting

  • Sensor not detected:
    • Ensure the insulation sheet has been removed from the battery.
    • Check if the battery is correctly installed and has sufficient charge.
    • Verify the sensor is in the correct mode (speed or cadence) for your intended use.
    • Make sure the sensor is activated by spinning the wheel (speed) or rotating the crank (cadence).
    • Confirm your cycling computer/app supports ANT+ or BLE and is within range.
  • Inaccurate speed data:
    • Ensure the correct wheel diameter is set in your cycling computer or app.
    • Check that the sensor is securely mounted on the wheel axle and not slipping.
  • Inaccurate cadence data:
    • Check that the sensor is securely mounted on the pedal crank and not slipping.

8. User Tips

  • This sensor is highly versatile and can be used for various cycling disciplines, including Mountain Biking (MTB), Road Biking, and with different cycling computers.
  • It is compatible with a wide range of bike speed boxes and cycling computers.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official ThinkRider website or contact your retailer. Keep your proof of purchase for any warranty claims.

© 2024 ThinkRider. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.