1. Introduction
This manual provides comprehensive instructions for the safe and efficient operation of your QIACHIP Multifunction RF Decoder and Module Test Tool. This device is designed to test the encoding type of remote controls, wireless code transmitting modules, wireless decoding receiving modules, wireless receiving modules, and wireless transmitting modules operating at 315 MHz and 433 MHz frequencies.
2. Safety Information
- Always handle electronic components with care to avoid damage.
- Keep the device away from water, moisture, and extreme temperatures.
- Do not attempt to disassemble or modify the device, as this may void the warranty and cause damage.
- Use only the specified DC5V power input.
3. Product Overview
The QIACHIP Multifunction RF Decoder is a versatile tool for working with various RF modules and remote controls. Below is a visual guide to its components:


Component List:
- LED Display
- Data Input (Data input port, not yet open)
- LED Indicators (Indicator light)
- ON/OFF (Power switch - down to open; up to off)
- DC5V Power Input (Power input interface micro USB, use ordinary Android charging cable)
- TX118S Module Port (Coding module port)
- 'ABCD' Button
- RX480E Module Port (Decoding module port)
- Transmit Module Port (Transmitter port)
- Receiver Module Port (Receiver module port)
- Toggle switch (Receive mode switch, 1: Use external receiver module for operation; 2: Work with built-in receiver)
4. Setup Instructions
- Power Connection: Connect a DC5V Micro USB cable to the power input port (5). Ensure a stable power source.
- Module Insertion: Carefully insert the desired RF module (e.g., TX118S, RX480E, or other transmitting/receiving modules) into its corresponding port (6, 8, 9, or 10). Ensure the pins are correctly aligned.
- Receive Mode Selection: Set the toggle switch (11) to '1' if you are using an external receiver module, or to '2' if you intend to use the built-in receiver for testing.
- Power On: Flip the ON/OFF switch (4) down to power on the device. The LED display (1) should light up, indicating the device is ready for operation.
5. Operating Instructions
5.1. Testing Remote Control Encoding
- Ensure the appropriate receiver module is connected or the built-in receiver is selected via the toggle switch (11).
- Power on the device. The LED display (1) will typically show "AUTO" or a similar standby message.
- Press a button on the remote control you wish to test.
- The LED display (1) will show the encoding type (e.g., 1527, 2262, HCS, HT, Rolling Code), data, and frequency (315MHz or 433MHz). The LED indicators (3) will flash to confirm signal reception.
5.2. Testing Transmitting Modules
- Insert the transmitting module into the Transmit Module Port (9).
- Power on the device.
- Press the 'ABCD' buttons (7) on the decoder to send signals. The LED indicators (3) will light up, and a separate receiving device (e.g., another decoder or receiver) should detect the signal.
5.3. Testing Receiving Modules
- Insert the receiving module into the Receiver Module Port (10).
- Set the toggle switch (11) to '1' for external module operation.
- Power on the device.
- Use a remote control or transmitting module to send a signal. The LED display (1) will show the received data, and the LED indicators (3) will flash.
5.4. Video Demonstration
6. Maintenance
- Cleaning: Use a dry, soft cloth to clean the device. Do not use liquids or abrasive cleaners.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
7. Troubleshooting
- Device not powering on: Check the Micro USB cable connection and ensure the power source is active. Verify the ON/OFF switch (4) is in the 'ON' position.
- No signal detected from remote control:
- Verify the remote control battery.
- Ensure the correct frequency (315MHz/433MHz) is being used by the remote and the decoder.
- Check if the receiver module is correctly inserted or the built-in receiver is selected via the toggle switch (11).
- Ensure the remote control is within close range of the decoder.
- Incorrect encoding displayed: Ensure the remote control is compatible with the decoder's supported encoding types (1527, 2262, HCS, HT, Rolling Code).
8. Specifications
| Attribute | Value |
|---|---|
| Brand Name | QIACHIP |
| Model Number | YMQ |
| Power Source | AC |
| Battery Included | Yes |
| Wireless Communication | Yes (RF) |
| Inbox Adaptor | No |
| High-concerned chemical | None |
| Communication method | RF |
| State of Assembly | Ready-to-Go |
| Features | Flashing |
| Control Channels | 4 channels |
| Origin | Mainland China |
| Certification | None |
9. User Tips
- For optimal performance, ensure your remote control or module is within close proximity to the decoder during testing.
- The device is capable of identifying and displaying the dip-switch settings of compatible remote controls directly on the LCD, which can be very helpful for replication or analysis.
10. Warranty & Support
For any issues, technical support, or warranty claims, please contact the seller directly. Keep your purchase records for reference.