1. Introduction
This manual provides detailed instructions for the safe and efficient operation of your QYT CB-58 Portable CB Radio. The QYT CB-58 is a compact and robust Citizen Band radio designed for reliable communication within the 26.965-27.405MHz frequency range, offering 4 watts of power across 40 AM/FM channels. Please read this manual thoroughly before using the device.
Note: The QYT CB-58 CB Radio cannot be programmed by the user.
2. Package Contents
Upon unpacking, please ensure all items listed below are present and in good condition:
- QYT CB-58 CB Radio Unit
- Rechargeable Battery (Model: QB58L, Capacity: 4100mAh, Voltage: 12V)
- Antenna
- Power Adapter
- Smart Charger Base
- Belt Clip
- Hand Strap
- User Manual (this document)
3. Product Overview
Familiarize yourself with the components and controls of your QYT CB-58 radio:
- FM Knob: Adjusts FM settings.
- Power Volume Knob: Turns the radio on/off and adjusts volume.
- LED: Status indicator light.
- Display: Shows frequency, mode, channel, and other operational information.
- AM/FM Button: Switches between AM and FM modulation modes.
- SCN (Scan) Button: Initiates channel scanning.
- EMG (Emergency) Button: Quick channel selection for emergency.
- MEM (Memory) Button: Accesses memory channels.
- FUN (Function) Button: Accesses menu functions.
- OK Button: Confirms selections.
- EXIT Button: Exits current menu or function.
- Antenna Connector: For attaching the antenna.
- PTT (Push-to-Talk) Button: Located on the side, used for transmitting.
- Speaker/Microphone Jack: Located on the side, for external audio accessories.
4. Setup
Follow these steps for initial setup of your CB-58 radio:
- Battery Installation:
- Align the battery pack (QB58L) with the battery compartment on the back of the radio.
- Slide the battery into place until it clicks securely.
- To remove, press the release latch (if present) and slide the battery out.
Figure 4.1: Battery Compartment
Figure 4.2: Battery Attached - Antenna Attachment:
- Screw the provided antenna clockwise onto the BNC connector at the top of the radio until it is finger-tight. Do not overtighten.
Figure 4.3: Antenna Attachment - Charging the Battery:
- Place the radio with the battery installed into the smart charger base.
- Connect the power adapter to the smart charger base and plug it into a power outlet.
- The charging indicator on the radio or charger will show the charging status. Ensure the battery is fully charged before first use.
Figure 4.4: Charging the Radio
Video 4.1: Demonstration of battery and antenna installation, and basic operation.
5. Operating Instructions
- Power On/Off and Volume Control:
- Rotate the Power Volume Knob clockwise to turn the radio ON. The display will light up.
- Continue rotating to increase the volume. Rotate counter-clockwise to decrease volume and turn OFF.
- Channel Selection:
- Use the channel selector knob (often combined with the Power Volume Knob or a separate rotary encoder) to change channels. The current channel number and frequency will be displayed.
- The radio supports 40 channels.
- AM/FM Modulation:
- Press the AM/FM button to switch between Amplitude Modulation (AM) and Frequency Modulation (FM) modes. The selected mode will be indicated on the display.
- Function (FUN) Button:
- Press the FUN button briefly to enter the menu mode.
- Press and hold the FUN button to perform a full reset of all functions.
- OK Button:
- Press the OK button to confirm a selection or exit after selection.
- Press and hold the OK button to turn off the screen and keyboard lights.
- Exit Button:
- Press the EXIT button to exit the current selection or menu.
- Scan (SCN) Button:
- Press the SCN button briefly to enter scanning mode.
- Press and hold the SCN button for 2 seconds to add or delete the current channel in the scan list.
- Emergency (EMG) Button:
- The EMG button provides quick channel selection for emergency use.
- Memory (MEM) Button:
- The MEM button is used for selection of regular channel groups and memory channel groups.
- Memory channels can be set by writing frequency software.
- Frequency Group Selection:
- Long press and hold the button to open the power to enter the frequency group selection. You can choose the regular group: EU Band, CE Band, U Band, PL Band, I2 Band, DE Band.
6. Specifications
6.1. General Specifications
| Feature | Specification |
|---|---|
| Modulation Mode | AM/FM |
| Frequency Range | 26.965-27.405MHz |
| Frequency Tolerance | 5.0ppm |
| Input Voltage | 12V |
| Dimensions (W x D x H) | 165mm x 67mm x 44mm |
| Weight | Approx. 444.5g |
| Frequency Control | PLL Synthesizer |
| Operating Temperature Range | -20℃ to 55℃ |
| Transmit Current | 2A MAX |
| Current Drain Receive (Squelched) | 0.3A |
| Current Drain Receive (VOL Max) | 0.8A |
| Antenna Connector | UHF SO-239 (BNC type for portable antenna) |
| Battery Capacity | 4100mAh |
| Waterproof / Water-Resistant | IP55 |
| Storage Channel | 40 |
| Maximum Range | 3km-5km |
| Material | PLASTIC+Metal |
6.2. Transmitter Specifications
| Feature | Specification |
|---|---|
| Power Output | 4 Watts FM/AM |
| Transmission Interference | Inferior to 4n W (-54dBm) |
| Frequency Response | 300-3000Hz |
| Modulated Signal Distortion | Inferior to 5% |
| Output Impedance | 50 ohms |
6.3. Receiver Specifications
| Feature | Specification |
|---|---|
| Sensitivity | Less than 1uV for 10dB (S+N)/N |
| Image Rejection | 70dB |
| Adjacent Channel Rejection | 60dB |
| IF Frequencies | 1st: 10.695MHz, 2nd: 455KHz |
| Automatic Gain Control (AGC) | Less than 10dB change in audio output for inputs from 10 to 50000uV |
| Squelch | Less than 1uV |
| Audio Output Power | 3 Watts into 8 ohms |
| Frequency Response | 300-3000Hz |
6.4. Channel Frequency Table
The QYT CB-58 supports various regional channel bands. Below is a table detailing the frequencies for each channel across different bands:
7. Maintenance
- Cleaning: Use a soft, damp cloth to clean the radio's exterior. Do not use harsh chemicals or abrasive cleaners.
- Storage: When not in use for extended periods, store the radio in a cool, dry place. Remove the battery if storing for several months to prevent discharge and potential damage.
- Battery Care: Avoid fully discharging the battery frequently. Recharge the battery regularly to maintain its lifespan.
- Antenna Care: Ensure the antenna is securely attached but do not overtighten. Avoid bending or stressing the antenna.
- Water Resistance: The radio has an IP55 rating, meaning it is protected against dust and low-pressure water jets. It is not designed for submersion.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Radio does not power on. | Battery is not installed correctly or is discharged. | Ensure battery is properly seated. Charge the battery fully. |
| No signal or poor reception. | Antenna not connected, incorrect channel/mode, or out of range. | Check antenna connection. Verify channel and AM/FM mode. Move to an area with better line-of-sight. |
| Cannot transmit. | PTT button not pressed, or radio is in receive-only mode. | Ensure PTT button is fully pressed. Check radio settings for transmit capability. |
| Display is blank or unresponsive. | Screen/keyboard lights turned off, or a system error. | Press and hold the OK button to toggle screen/keyboard lights. Perform a full reset (long press FUN button). |
9. User Tips
- Battery Life: The 4100mAh battery provides extended operation. For optimal performance, fully charge the battery before each significant use.
- Antenna Connection: Always ensure the antenna is properly connected before powering on the radio to prevent damage to the transceiver.
- Channel Selection: Be aware of the specific channel regulations and common usage in your region (e.g., Channel 9 for emergency calls in some areas). Refer to the Channel Frequency Table for regional band details.
- Portability: Utilize the included belt clip and hand strap for convenient and secure carrying during outdoor activities.
10. Warranty and Support
The QYT CB-58 CB Radio comes with a 12-month warranty for the main unit and a 6-month warranty for accessories from the date of receipt. For technical support or warranty claims, please contact your seller or refer to the official QYT website for service information.