1. Product Overview
The Granzon Water Cooling Kit is a universal liquid cooling solution designed for both CPU and GPU blocks, featuring a G1/4'' interface for broad compatibility. This kit provides efficient thermal management for high-performance PC systems.
Video: Granzon Water Cooling Kit System Showcase. This video demonstrates the kit installed in a PC, highlighting its RGB lighting and components.
2. Kit Contents
Please verify that all components are present before beginning installation. Note: Cooling liquid is not included and must be purchased separately.
2.1. 240mm Kit List
- 1x DDC Pump
- 1x Pump Bridge Module
- 2x 120mm Fans
- 2x Soft Tubes
- 2x 90° Fittings
- 1x 240mm Radiator
Image: Contents of the 240mm Water Cooling Kit, including pump, bridge, fans, tubes, fittings, and radiator.
2.2. 360mm Kit List
- 1x DDC Pump
- 1x Pump Bridge Module
- 3x 120mm Fans
- 2x Soft Tubes
- 2x 90° Fittings
- 1x 360mm Radiator
Image: Contents of the 360mm Water Cooling Kit, including pump, bridge, three fans, tubes, fittings, and radiator.
3. Setup and Installation
Before starting, ensure your computer is powered off and unplugged. It is recommended to remove the motherboard from the computer case for safer installation.
3.1. CPU Water Block Installation
- Prepare Backplane: Install the backplane from the rear of the motherboard. Carefully fit and align the screw bits with the motherboard holes.
- Apply Thermal Grease: Apply an even, appropriate amount of thermal grease onto the CPU. Ensure the center of the CPU is covered where the water block will make contact.
- Mount Water Block: First, set the springs and gaskets onto the mounting screws. Then, screw in the water block diagonally, following an assembly sequence to ensure even pressure. After all four screws are engaged, tighten the corners in turn.
3.2. GPU Water Block Installation (if applicable)
- Insert GPU Block: Carefully insert the GPU water cooling block into the graphics card slot on your motherboard.
Image: Installation Step 1 - Inserting the GPU water cooling block into the graphics card slot.
3.3. Radiator and Fan Installation
- Fix Radiator: Secure the radiator in your PC case according to its actual position and mounting points.
Image: Installation Step 2 - Securing the radiator within the PC case.
- Attach Fans: Secure the 120mm fans to the radiator using the provided screws. Ensure the fan orientation is correct for optimal airflow (push or pull configuration).
Image: Installation Step 3 - Attaching the 120mm fans to the radiator.
3.4. Tubing and Filling
- Connect Tubing: Connect the soft tubes between the water blocks, pump, and radiator using the 90° fittings. Ensure all connections are secure to prevent leaks.
- Fill Loop: Carefully fill the cooling loop with a compatible liquid cooling fluid (not included). Ensure the reservoir is adequately filled and bleed any air from the system by gently tilting the PC case.
4. Operating Instructions
The Granzon Water Cooling Kit features an integrated control panel for managing fan speed, pump speed, and lighting.
Image: Product dimensions and control panel diagram. The diagram shows controls for power, fan speed, pump speed, light speed, and manual/automatic mode.
4.1. Control Panel Functions
- Power Button: Turns the unit on/off.
- FAN SPEED +/-: Adjusts the speed of the cooling fans.
- PUMP SPEED +/-: Adjusts the speed of the DDC pump.
- LIGHT SPEED: Adjusts the speed or pattern of the ARGB lighting.
- M/A (Manual/Automatic): Toggles between manual control and automatic (PWM) control for pump speed.
4.2. Pump Speed Control
- Manual Mode: In manual mode, the pump speed can only be adjusted using the included remote controller.
- Automatic (PWM) Mode: To enable automatic speed adjustment via your PC's BIOS, ensure a CR2025 battery is inserted into the remote controller. Use the remote to switch the pump to automatic mode. You can then configure pump speed curves in your motherboard's BIOS settings.
5. Maintenance
- Fluid Level Check: Periodically check the coolant level in the reservoir. Top up with compatible liquid cooling fluid if necessary.
- Dust Cleaning: Regularly clean dust from the radiator fins and fan blades using compressed air or a soft brush to maintain optimal cooling performance.
- Leak Inspection: Periodically inspect all fittings and tubing for any signs of leaks. Tighten fittings if any looseness is detected.
- Fluid Replacement: It is recommended to replace the cooling fluid every 6-12 months, depending on the fluid type and usage, to prevent buildup and maintain system efficiency.
6. Troubleshooting
- High Temperatures:
- Ensure the pump is running (check display/sound).
- Verify fans are spinning and properly oriented.
- Check coolant level and ensure no air bubbles are trapped.
- Clean dust from radiator and fans.
- Re-apply thermal paste to CPU/GPU if necessary.
- Leaking:
- Immediately power off the PC.
- Identify the source of the leak.
- Tighten any loose fittings. If a component is damaged, it may need replacement.
- RGB Lighting Not Working:
- Check all ARGB connections to the controller and motherboard.
- Ensure the controller is powered.
- Try adjusting light settings via the control panel or motherboard software.
7. Specifications
| Brand Name | bykski |
| Model Number | GZGPU-M240N |
| Type | Cooling Bundle |
| Material | Copper |
| RGB Support | A-RGB (5V ARGB) |
| Interface | G1/4'' |
| Fan Size | 120mm |
| Fan Speed | 1500 (±10%) RPM |
| Fan Airflow | 64.8 CFM |
| Pump Speed | 1800-4800 RPM |
| Pump Flow Rate | 700 L/H |
| Dimensions (Approx.) | 124.5 x 330.9 x 62.1 mm (for integrated unit) |
| Certification | CE |
| Origin | Mainland China |
8. User Tips
- Pump Control: For automatic pump speed control via your PC's BIOS, ensure the remote controller has a CR2025 battery and is used to set the pump to automatic (PWM) mode. Manual mode requires the remote for speed adjustments.
- Compatibility Check: Before purchasing, always verify the dimensions of the radiator and integrated unit to ensure it fits your PC case (e.g., Corsair 4000D). Also, confirm compatibility with your specific GPU model if using a GPU water block.
- Temperature Monitoring: Utilize software to monitor CPU and GPU temperatures to ensure the cooling system is performing optimally.
9. Warranty and Support
For any issues, technical support, or warranty claims, please contact the seller or manufacturer directly through your purchase platform. Keep your proof of purchase for warranty validation.