Ziqqucu TinyLev

Contents

Ultrasonic Levitation Acoustic Electronics DIY Kit User Manual

Model: TinyLev

1. Introduction

The Ultrasonic Levitation Acoustic Electronics DIY Kit, also known as TinyLev, is an educational project designed to demonstrate the principles of acoustic levitation. This phenomenon utilizes the mechanical energy of sound waves to exert a force on an object, counteracting gravity and allowing the object to levitate. Unlike magnetic levitation, acoustic levitation can be applied to a wider range of materials, including liquids and small insects. This kit is provided unassembled, offering a hands-on learning experience in electronics and physics.

Assembled Ultrasonic Levitation Kit
Figure 1: Assembled Ultrasonic Levitation Kit

2. Package Contents

Please inspect the package carefully to ensure all components are present and undamaged:

  • 3D-printed TinyLev Frame x1
  • Arduino Nano with Mini USB Cable x1
  • 10mm 40kHz Transducers x76
  • L298N Dual Motor Drive Board x1
  • DC Power Adaptor (9V) x1
  • Power Switch x1
  • DC Female Connector (5.5 x 2.1mm) x1
  • Buttons x3
  • Jumper Wires (assorted)
  • Black and Red Wires (assorted)
  • Exposed Wires (assorted)
Ultrasonic Levitation Kit Components
Figure 2: All components included in the DIY kit

3. Setup and Assembly

This kit requires assembly. Follow the instructions carefully. A detailed user manual (PDF) may be available from the seller for more in-depth assembly steps: User Manual PDF.

3.1 Mechanical Assembly

  1. Mount the 76 transducers onto the designated slots on the 3D-printed TinyLev frame. Ensure they are securely seated in both the top and bottom arrays.
  2. Position the top and bottom arrays parallel to each other, maintaining the specified distance (approximately 20mm as shown in diagrams).

3.2 Electrical Wiring

Refer to the wiring diagram below for all electrical connections. Ensure all connections are secure and correctly oriented before applying power.

Wiring Diagram for Ultrasonic Levitation Kit
Figure 3: Wiring Diagram. Connect components as shown.
  • Power Circuit:
    1. Connect the DC female connector to the power switch.
    2. Connect the power switch output to the L298N Dual Motor Drive Board (power input) and the Arduino Nano (VIN pin).
  • Arduino Nano Connections:
    1. Connect the Arduino Nano's digital pins (D2-D7) to the corresponding input pins on the L298N driver board.
    2. Connect the three buttons to Arduino Nano digital pins (e.g., D8, D9, D12) and ground, using pull-down resistors if necessary (not explicitly shown in diagram but good practice).
    3. Ensure a jumper wire connects pins D10 and D11 on the Arduino Nano as indicated.
  • Transducer Array Connections:
    1. Connect the Top Array of transducers to one output channel of the L298N driver board.
    2. Connect the Bottom Array of transducers to the other output channel of the L298N driver board.
    3. Ensure correct polarity for all transducer connections.

For a visual guide, you may find external videos helpful, such as: https://www.youtube.com/watch?v=ABjRnSYw-4k

4. Operating Instructions

Once the kit is fully assembled and wired, you can begin experimenting with acoustic levitation.

  1. Power On: Connect the 9V DC power adaptor to the DC female connector and flip the power switch to the ON position. The Arduino Nano and L298N board should power up.
  2. Object Placement: Carefully place a small, lightweight object (e.g., a foam bead, a tiny piece of paper, a water droplet, or a small insect) into the space between the top and bottom transducer arrays.
  3. Levitation Control: Use the three buttons to control the levitation. These buttons typically adjust parameters such as the phase difference between the arrays or the frequency, which can affect the stability and position of the levitated object. Experiment with different button presses to find the optimal settings for levitation.
  4. Observation: Observe the object as it levitates in the acoustic field. Adjust the object's initial position and button controls for stable levitation.
Various objects levitated by the device
Figure 4: Examples of objects that can be levitated

Watch a demonstration of the kit in action:

Video 1: Demonstration of a small bead being levitated.

5. Maintenance

  • Cleaning: Keep the transducers and electronic components free from dust and debris. Use a soft, dry cloth for cleaning.
  • Storage: Store the kit in a dry, cool place away from direct sunlight and moisture.
  • Connections: Periodically check all wire connections to ensure they remain secure. Loose connections can lead to erratic behavior or component damage.
  • Handling: Handle the transducers and circuit boards with care to avoid physical damage.

6. Troubleshooting

6.1 No Power

  • Ensure the 9V DC power adaptor is correctly plugged into a working outlet and the DC female connector.
  • Check that the power switch is in the ON position.
  • Verify all power connections from the DC connector through the switch to the Arduino Nano and L298N board.

6.2 No Levitation or Unstable Levitation

  • Wiring: Double-check all wiring according to the diagram (Figure 3). Incorrect connections to the L298N or transducers are common issues.
  • Transducers: Ensure all 76 transducers are properly connected and functioning. A faulty transducer can disrupt the acoustic field.
  • Object Properties: The object being levitated must be small and lightweight. Heavier or larger objects may not levitate.
  • Environment: Ensure the operating environment is still, without significant air currents (e.g., from fans, open windows) that could disturb the levitated object.
  • Button Controls: Experiment with the button controls to find the correct phase and frequency settings for stable levitation.
  • Power to Arrays: Verify that the L298N driver board is receiving power and correctly driving both the top and bottom transducer arrays.

7. Specifications

FeatureSpecification
Product TypeUltrasonic Suspension DIY Learning Kit
ControllerArduino Nano
Driver BoardL298N Dual Motor Drive Board
Transducers76 x 10mm, 40kHz
Power Supply9V DC (adaptor included)
Package Dimensions (L x W x H)21 cm x 11 cm x 14 cm
Package Weight0.441 kg

8. User Tips

  • Secure Connections: Always double-check all electrical connections before powering on the device to prevent short circuits or damage.
  • Start Small: Begin levitation experiments with very light and small objects, such as tiny foam beads, to easily observe the effect.
  • Still Environment: Perform experiments in a room with minimal air movement to ensure stable levitation and prevent objects from being blown away.
  • Patience is Key: Acoustic levitation can be sensitive. It may take some practice to find the optimal settings and object placement for stable levitation.

9. Frequently Asked Questions (FAQ)

Q: Is this kit pre-assembled?

A: No, this is an unassembled DIY kit designed for learning and hands-on experience.

Q: What kind of objects can I levitate?

A: You can levitate small, lightweight objects such as foam beads, tiny pieces of paper, water droplets, or small insects.

Q: What power supply is needed?

A: A 9V DC power adapter is included with the kit.

Q: Where can I find more detailed assembly instructions?

A: A detailed user manual in PDF format may be available from the seller. Please refer to the product page or contact the seller for more information.

10. Warranty and Support

For any issues, technical support, or warranty inquiries, please contact the seller directly through the platform where you purchased the kit. Provide your order details for faster assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.