Product Overview
The MILES DG01487 is a gas-pressurized front shock absorber designed for the Renault Fluence, specifically models from 2010 onwards. This component is crucial for maintaining vehicle stability, ride comfort, and handling performance by dampening suspension oscillations.


Specifications
| Attribute | Value |
|---|---|
| Manufacturer Part Number | DG01487 |
| Brand Name | MILES |
| Type | Air Pressure (Gas) |
| Installation Side | Front Axle |
| Shock Absorber Type | Gas Pressure; Suspension Strut |
| Origin | Russia |
Package Dimensions:
- Length: 20 cm
- Width: 30 cm
- Height: 10 cm
- Weight: 2.9 kg
Setup and Installation
Important: Installation of automotive suspension components, including shock absorbers, requires specialized tools, knowledge, and safety precautions. It is highly recommended that this product be installed by a qualified and certified automotive technician.
Pre-Installation Checks:
- Verify that the shock absorber model (DG01487) is correct for your Renault Fluence (2010- front axle).
- Inspect the new shock absorber for any signs of damage during shipping.
- Ensure all necessary mounting hardware (not always included) is available and in good condition.
General Installation Steps (for professional reference):
- Safely lift and support the vehicle on jack stands.
- Remove the wheel.
- Disconnect any brake lines, ABS sensors, or sway bar links attached to the strut assembly.
- Unbolt the lower mounting bolts connecting the strut to the steering knuckle.
- Access the upper strut mounts (usually under the hood or inside the cabin) and remove the nuts.
- Carefully remove the old strut assembly.
- If reusing the coil spring, use a spring compressor to safely remove it from the old strut and transfer it to the new MILES DG01487 shock absorber. Replace the strut mount, boot, and bump stop if necessary.
- Install the new strut assembly in reverse order, ensuring all bolts are torqued to manufacturer specifications.
- Re-attach all disconnected components.
- Lower the vehicle and perform a wheel alignment.
Always refer to your vehicle's specific service manual for detailed torque specifications and procedures.
Operating Information
Once installed, the MILES DG01487 shock absorber operates automatically as part of your vehicle's suspension system. It is designed to absorb road impacts and control spring oscillations, providing a smooth and stable ride.
Normal Operation:
- The vehicle should exhibit improved ride comfort and reduced body roll.
- Steering response and overall handling should feel more precise.
- Braking stability should be enhanced.
No user intervention is required for the operation of the shock absorber itself.
Maintenance
Shock absorbers are generally maintenance-free components. However, regular inspection of your vehicle's suspension system is recommended to ensure optimal performance and longevity.
Recommended Checks:
- Visual Inspection (Every 12,000 miles or annually):
- Check for oil leaks around the shock absorber body. A light film is normal, but excessive fluid indicates a seal failure.
- Inspect the shock absorber rod for bends, dents, or corrosion.
- Examine the rubber bushings and mounts for cracks, tears, or excessive wear.
- Check for loose or missing mounting bolts.
- Performance Check: If you notice a decrease in ride comfort, excessive bouncing, or poor handling, have your suspension system inspected by a professional.
Promptly address any issues found during inspection to prevent further damage to other suspension components or compromise vehicle safety.
Troubleshooting
If you experience issues with your vehicle's suspension after installing or during the use of the MILES DG01487 shock absorber, consider the following common problems and potential causes:
| Symptom | Possible Cause | Action |
|---|---|---|
| Excessive Bouncing / Poor Ride Quality | Worn or faulty shock absorber, incorrect installation, or issues with other suspension components (e.g., springs). | Inspect shock absorber for leaks or damage. Verify proper installation. Check other suspension parts. |
| Clunking or Knocking Noises | Loose mounting bolts, worn bushings, faulty strut mount, or contact with other components. | Check all mounting points for tightness. Inspect bushings and strut mounts for wear. |
| Uneven Tire Wear | Worn suspension components, including shock absorbers, or improper wheel alignment. | Have suspension system inspected and wheel alignment checked by a professional. |
| Fluid Leaks from Shock Absorber | Damaged seal or internal component failure. | Shock absorber replacement is typically required. |
For persistent or severe issues, consult a professional automotive technician.
User Tips
- Professional Installation: Always prioritize professional installation for suspension components to ensure safety and correct function.
- Pair Replacement: For optimal performance and even wear, it is generally recommended to replace shock absorbers in pairs (both front or both rear), even if only one appears faulty.
- Post-Installation Alignment: After replacing front suspension components, a wheel alignment is crucial to prevent premature tire wear and ensure proper vehicle handling.
- Regular Inspections: Incorporate visual checks of your shock absorbers into your routine vehicle maintenance to catch potential issues early.
Warranty and Support
For specific warranty information regarding the MILES DG01487 shock absorber, please refer to the documentation provided at the time of purchase or contact the MILES brand directly through their official channels. Keep your purchase receipt as proof of purchase.
If you require technical assistance or have questions about the product, please contact the seller or the MILES customer support team.