1. Introduction
This manual provides instructions for the safe and effective use of your HIHAILE TL20 IP68 Waterproof Connector. This T-type electrical terminal adapter is designed for reliable connections in demanding outdoor environments, including outdoor LED lights, security monitoring systems, automotive wiring harnesses, marine equipment, and industrial automation.
The connector features robust housing, corrosion-resistant terminals, and simple screw-terminal wiring for easy installation.
2. Safety Warnings
- Do not plug or unplug while powered on: Always cut off power before operation to avoid short circuit, electric shock, or equipment damage.
- Waterproof rating: IP68 waterproof rating is achieved only when connectors are fully mated and locked. Unmated connectors have NO waterproof capability.
- Immersion: IP68 withstands long-term immersion. Do not use in corrosive gases or liquids for extended periods.
- Modification: Do not modify or disassemble the product. Unused connectors must be covered with dustproof/waterproof caps. Perform a waterproof test after installation and confirm no leakage before energizing.
- Children: Keep out of reach of children to prevent accidental ingestion or electric shock.
3. Product Overview
The HIHAILE TL20 waterproof connector is a T-type electrical terminal adapter designed for secure and reliable outdoor connections. It is available in 2-pin and 3-pin configurations.
4. Specifications
| Attribute | Value |
|---|---|
| Model Number | TL20 |
| Brand Name | HIHAILE |
| Product Name | Waterproof Connector |
| Features | Waterproof |
| Number of cores | 2P, 3P |
| Applicable cable diameter | 3-7mm, 6-12mm |
| Working temperature | -40 ℃ ~ 105 ℃ |
| Applicable materials | Flame retardant nylon PA66 |
| Voltage | 220 V (Note: EU LVD Voltage is below 50Vac or 75Vdc) |
| Withstand voltage | 2000 V |
| Current/Voltage (from diagram) | 16 A / 380 V |
| Protection grade | IP68 |
| Connection mode | Screw pressing connection |
| Contact material | Brass nickel plated |
| Certificates | CE, RoHS, SCCP, REACH-SVHC |
| Wireless functionality | No |
| Includes Battery | No |
| High-concerned chemical | None |
For detailed compliance information, refer to the LVD Compliance Verification Certificate (PDF).
5. Setup and Installation
Follow these steps for proper wiring and installation of the waterproof connector:
- Unscrew both ends of the waterproof connector and remove the terminals.
- Unscrew the nuts at both ends.
- Select the appropriate rubber ring size according to your cable diameter to ensure a tight seal.
- Insert the cable through the nut and then the rubber ring in order.
- Loosen the terminal screws, insert the stripped cable wires into the terminals, and then tighten the screws securely.
- Repeat steps 1-5 for the other end of the connection.
- Tighten the two split parts of the connector firmly to complete the wiring and ensure the IP68 seal.
6. Operating Instructions
Once installed, the connector provides a secure and waterproof electrical connection. Ensure all connections are fully tightened to maintain the IP68 waterproof integrity. The connector is designed for continuous operation within its specified temperature and voltage ranges.
7. Maintenance
- Storage: Store the connector in a dry, ventilated, non-corrosive environment at temperatures between -20°C and +60°C.
- Environment: Avoid direct sunlight and heavy pressure on the connector.
- Inspection: For outdoor use, inspect the connector every 3-6 months for any signs of wear, damage, or loose connections.
- Cleaning: Clean the connector with a dry cloth or anhydrous alcohol. Do not rinse unmated connectors with water.
8. Troubleshooting (FAQs)
- Q: No waterproof capability after installation?
- A: Ensure both ends are fully tightened and the connector is completely mated. Perform a 30-minute immersion test to verify the seal.
- Q: Can I plug/unplug under load?
- A: No. Always cut off power first before plugging or unplugging the connector.
- Q: How to perform a waterproof test?
- A: Spray or immerse the connector in water for 30 minutes. After 30 minutes, wipe it dry and verify that there is no internal water accumulation. Then, conduct a power-on test.
- Q: How to fix the connector?
- A: Use cable ties or brackets to secure the connector and cable, preventing long-term stress or vibration that could compromise the connection.
- Q: How to clean?
- A: Wipe with a dry cloth or anhydrous alcohol. Do not use water directly on unmated connectors.
9. User Tips
- When using flexible cables, it is recommended to crimp the multi-strand conductive part with cylindrical terminals. This facilitates easier wiring and ensures that the sealing gasket fully presses against the cable sheath for an optimal seal.
- Always specify the correct sealing ring size when ordering, especially for cables with larger diameters (e.g., 11mm), to ensure a perfect fit and waterproof integrity.
10. Warranty and Support
For any issues, questions, or support needs regarding your HIHAILE TL20 Waterproof Connector, please contact HIHAILE official customer service.