lilygo Q320

Contents

LILYGO® TTGO T-U2T USB To TTL CH9102F Serial Module User Manual

Model: Q320 | Brand: LILYGO

1. Introduction

The LILYGO T-U2T is an innovative USB to TTL serial module designed to simplify ESP32 circuit board development. It integrates a USB Type-C interface with a CH9102F serial chip and an automatic download circuit into a compact adapter form factor. This design eliminates the need for redundant USB to TTL circuits on development boards, saving space and reducing manufacturing costs.

This module is ideal for LILYGO motherboards and other products that require a USB to TTL serial converter for programming and communication, especially those without an onboard USB-to-Serial chip.

LILYGO T-U2T USB to TTL Module front and back view
Figure 1: LILYGO T-U2T USB to TTL Module (Front and Back)

2. Specifications

FeatureDescription
Model NumberQ320
Serial ChipCH9102F
InterfaceUSB Type-C (Male) to USB Type-C (Female)
FunctionUSB to TTL Serial Converter, Automatic Downloader
CompatibilityLILYGO motherboards and other products without USB-to-Serial chip
Dimensions (Approx.)Length: 3.86cm, Width: 1.25cm, Height: 0.8cm
PackageYes
OriginMainland China
CertificationNONE
LILYGO T-U2T Module Dimensions
Figure 2: LILYGO T-U2T Module Dimensions

3. Setup Instructions

The LILYGO T-U2T module is designed for easy integration with development boards that lack an onboard USB-to-Serial chip. Follow these steps for proper connection:

  1. Identify Compatible Board: Ensure your development board (e.g., ESP32 board) does not have its own USB-to-Serial chip. If it does, the T-U2T is not required for programming.
  2. Connect to Development Board: Plug the male Type-C connector of the T-U2T module into the corresponding female Type-C port on your development board.
  3. Connect to PC: Use a standard Type-C to USB data cable to connect the female Type-C port of the T-U2T module to your computer's USB port.
  4. Driver Installation: The CH9102F chip typically uses standard USB serial drivers. If your operating system does not automatically install the driver, you may need to download and install the appropriate CH9102F driver from the chip manufacturer's website.
  5. UART Pin Mapping: The T-U2T internally handles the TX/RX exchange. When connecting to your board, ensure the UART pins (TX, RX, GND) are correctly aligned. Refer to the diagrams below for typical connections.
T-U2T User Guide Compatible Development Boards and UART Pin Mapping
Figure 3: T-U2T User Guide - Compatible Development Boards and UART Pin Mapping. Shows how to connect the T-U2T to a board's I01/TX, I03/RX, and GND pins, with the T-U2T's RX connecting to the board's TX, and the T-U2T's TX connecting to the board's RX.
T-U2T connection diagram with a display board
Figure 4: T-U2T connection diagram with a display board, illustrating the internal TX/RX exchange.
T-U2T USB connection diagram to PC
Figure 5: T-U2T USB connection diagram, showing connection to a product with a boot button and then to a PC via a Type-C to USB data cable.
Explanation for T-U2T necessity
Figure 6: Explanation that the T-U2T is needed for uploading programs to motherboards without an integrated USB to serial chip.

4. Operating Instructions

Once the T-U2T module is correctly connected to your development board and computer, it functions as a standard USB to serial converter, enabling communication and program uploading.

  1. Program Uploading: For boards like ESP32 that require a program upload, connect the T-U2T as described in the setup section. Open your preferred IDE (e.g., Arduino IDE, PlatformIO) and select the correct serial port corresponding to the T-U2T module. Ensure the board type and other settings are configured for your specific development board.
  2. Automatic Download: The T-U2T includes an automatic download circuit. This means that for compatible boards, you typically do not need to manually press a 'boot' or 'reset' button during the upload process. The module handles the necessary signals to put the board into programming mode.
  3. Serial Communication: The module can also be used for general serial communication (e.g., viewing debug messages from your board). Open a serial monitor in your IDE or a dedicated terminal program, select the correct COM port and baud rate, and you should be able to send and receive data from your connected board.

5. Maintenance

The LILYGO T-U2T module is a robust electronic component that requires minimal maintenance. Follow these guidelines to ensure its longevity:

  • Storage: Store the module in a dry, cool environment, away from direct sunlight and extreme temperatures.
  • Cleaning: If necessary, gently wipe the module with a dry, soft cloth. Avoid using liquids or abrasive cleaners.
  • Handling: Handle the module by its body, avoiding excessive force on the connectors.
  • Avoid Static Discharge: Take precautions against electrostatic discharge (ESD) when handling the module, as it contains sensitive electronic components.

6. Troubleshooting

If you encounter issues with your LILYGO T-U2T module, consider the following troubleshooting steps:

  • Module Not Recognized by PC:
    - Ensure the Type-C to USB data cable is fully inserted into both the T-U2T and your PC.
    - Try a different USB port on your computer.
    - Try a different Type-C to USB data cable.
    - Verify that the CH9102F driver is correctly installed. Check Device Manager (Windows) or `ls /dev/tty*` (Linux/macOS) for the serial port.
  • Program Upload Fails:
    - Double-check that the T-U2T is securely connected to your development board.
    - Ensure the correct serial port is selected in your IDE.
    - Verify that the baud rate and board settings in your IDE match the requirements of your development board.
    - Confirm that your development board is compatible with the T-U2T (i.e., it lacks an onboard USB-to-Serial chip).
    - If your board has a 'boot' button, try holding it down during the upload process, although the T-U2T's automatic download circuit should negate this need for most compatible boards.
  • No Serial Output:
    - Ensure the correct serial port and baud rate are selected in your serial monitor/terminal.
    - Verify that your development board is actually sending data over its UART pins.
    - Check the wiring between the T-U2T and your board, especially the TX/RX lines. Remember the T-U2T internally swaps TX/RX, so connect T-U2T RX to board TX, and T-U2T TX to board RX.

7. User Tips

Based on general usage patterns for similar devices, here are some tips:

  • Keep Drivers Updated: Periodically check for updated drivers for the CH9102F chip to ensure optimal performance and compatibility with newer operating systems.
  • Cable Quality Matters: Use high-quality USB Type-C cables to avoid connection issues and ensure stable data transfer.
  • Verify Pinouts: Always double-check the pinout diagrams for your specific development board and the T-U2T to prevent incorrect connections that could damage components.

8. Warranty and Support

For warranty information and technical support, please refer to the official LILYGO P-IOT Store or the retailer from whom you purchased the product. Keep your proof of purchase for any warranty claims.

For additional resources and community support, you may visit the LILYGO official website or relevant online forums dedicated to ESP32 development and LILYGO products.

9. Package Contents

The standard package for the LILYGO T-U2T USB To TTL module includes:

  • 1 x LILYGO T-U2T USB To TTL Module

© 2024 LILYGO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.