Estardyn XH-M609

Contents

Instruction Manual

Estardyn XH-M609 DC 12V-36V Battery Overdischarge Protection Module

Model: XH-M609 (also known as HCW-M635) | Brand: Estardyn

1. Introduction and Overview

The Estardyn XH-M609 (HCW-M635) is a versatile DC 12V-36V battery overdischarge protection module designed to safeguard various storage batteries and lithium batteries from excessive discharge. This module features precise undervoltage protection, automatic power-off capabilities, and helps prolong battery life by preventing damage from deep discharge. It includes a digital display for real-time voltage monitoring and intuitive button controls for setting protection parameters.

2. Specifications

No.ParameterValue
1Product NameBattery Overdischarge Protection Module
2ModelXH-M609 / HCW-M635
3Power Supply VoltageDC 12V-36V (for various batteries)
4Output VoltageEqual to power supply voltage
5Control Precision0.1 V
6Power ConsumptionLess than 1.5 W
7Scope of ApplicationVarious storage batteries, lithium batteries
8Net Weight28 g
9Size57 x 42 x 19 mm
10Relay Current Rating20A 14VDC / 20A 125VAC

3. Safety Information

  • Always ensure correct polarity when connecting the module to the power source and load. Incorrect wiring can damage the module or connected devices.
  • Operate within the specified voltage range (DC 12V-36V). Exceeding this range may lead to malfunction or damage.
  • Avoid short circuits on the input or output terminals.
  • Keep the module away from moisture, dust, and extreme temperatures.
  • If you are unsure about any wiring or setup steps, consult a qualified electrician or electronics technician.

4. Product Diagrams

Wiring diagram for XH-M609 module showing connections to a storage battery and output load.

Figure 1: Wiring Diagram for XH-M609 Module

Dimensional drawing of the XH-M609 module, including measurements for length, width, and component placement.

Figure 2: XH-M609 Module Dimensions

Angled view of the XH-M609 module, showing the digital display and control buttons.

Figure 3: XH-M609 Module with Digital Display and Buttons

5. Setup and Wiring

Refer to Figure 1 for the wiring diagram. The module has two main connection points: input (VIN) and output (VOUT).

  1. Input Connection (VIN): Connect your DC power source (battery) to the VIN terminals. Ensure the red wire connects to the positive (+) terminal and the black wire to the negative (-) terminal. The module supports 12V-36V DC input.
  2. Output Connection (VOUT): Connect your load (e.g., pump, light) to the VOUT terminals. Again, ensure correct polarity: red wire to positive (+), black wire to negative (-). The output voltage will be equal to the input power supply voltage when the module is active.
  3. Relay Rating: The integrated relay is rated for a maximum of 20A at 14VDC or 20A at 125VAC. Ensure your load's current draw does not exceed these limits.

6. Operating Instructions

The XH-M609 module features a digital display and two control buttons for setting the protection voltage and return difference.

Instruction text for button functions: '+' button for protection value, '-' button for return difference value.

Figure 4: Button Functions

  1. Power On: Connect the module to a DC power source within the 12V-36V range. The digital display will show the current voltage.
  2. Setting Protection Voltage (Cutoff Voltage):
    • Press the 'SET' button (labeled '+') once to display the current protection voltage.
    • Long press the 'SET' button (labeled '+') until the displayed voltage starts flashing.
    • Use the '+' and '-' buttons to adjust the desired protection (cutoff) voltage. This is the voltage at which the module will disconnect the load to prevent overdischarge.
    • Once set, wait a few seconds without pressing any buttons; the module will automatically save the setting.
  3. Setting Return Difference Value (Hysteresis):
    • Press the 'MODE' button (labeled '-') once to display the current return difference value.
    • Long press the 'MODE' button (labeled '-') until the displayed value starts flashing.
    • Use the '+' and '-' buttons to adjust the desired return difference value. This value determines how much the battery voltage must rise (e.g., through charging) above the cutoff voltage before the module reconnects the load. For example, if cutoff is 10V and return difference is 2V, the load will reconnect when the battery reaches 12V.
    • Once set, wait a few seconds without pressing any buttons; the module will automatically save the setting.
  4. Operation Logic: The module continuously monitors the battery voltage. When the voltage drops below the set protection voltage, the module will disconnect the load after a short delay (approximately 3 seconds). It will remain disconnected until the battery voltage rises above the protection voltage plus the return difference value, at which point it will automatically reconnect the load.

Video 1: Demonstration of XH-M609 Module Operation and Setting

7. User Tips

  • Settings Memory: The module retains its voltage settings even after power is disconnected, so you only need to set them once.
  • Battery Compatibility: This module is suitable for a wide range of storage batteries, including AGM batteries, and lithium batteries, provided they operate within the 12V-36V DC range.
  • Practical Use: Ideal for applications requiring automatic cutoff to prevent battery damage from over-discharge, thereby extending the lifespan of your batteries.

8. Troubleshooting

  • Module Not Activating/Outputting Power:
    • Check if the input voltage is within the 12V-36V range.
    • Verify that the current battery voltage is above the set protection voltage plus the return difference value. If it's below this threshold, the module will not activate the output.
    • Ensure all wiring connections are secure and correct, paying close attention to polarity.
  • Module Not Cutting Off Power:
    • Confirm that the set protection voltage is appropriate for your battery type and desired cutoff point.
    • Check if the load's current draw exceeds the relay's maximum rating (20A). Overloading can prevent proper operation or damage the relay.
  • Inaccurate Voltage Reading: Ensure stable power input and check connections for any loose contacts.

9. Maintenance

  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to water or excessive humidity.
  • Periodically check wiring connections for tightness and signs of wear.
  • Store in a dry, cool environment when not in use.

10. Warranty and Support

For any issues, technical support, or warranty claims, please contact your seller or the manufacturer directly. Provide your product model (XH-M609) and a detailed description of the problem for efficient assistance.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.