Espressif ESP-C3-12F KIT

Contents

ESP-C3-12F KIT Development Board User Manual

Model: ESP-C3-12F KIT | Brand: Espressif

1. Introduction

The ESP-C3-12F KIT is a low-cost development board featuring the Espressif ESP32-C3 microcontroller. This board integrates 2.4 GHz Wi-Fi and Bluetooth 5.0 (LE) capabilities, making it ideal for a wide range of IoT applications. It offers a compact design with rich peripheral interfaces, suitable for both prototyping and embedded system development.

Top-down view of the ESP-C3-12F KIT development board
Figure 1: ESP-C3-12F KIT Development Board

2. Product Overview

The ESP-C3-12F KIT is designed for ease of use and flexibility. It comes in variants with either 2MByte or 4MByte SPI flash memory, providing options for different application requirements. The board includes a Micro USB interface for power and data communication, a 3.3V voltage regulator (AMS1117), and various GPIO pins for connecting external sensors and actuators.

Image showing both 2M and 4M flash versions of the ESP-C3-12F KIT
Figure 2: ESP-C3-12F KIT with 2M and 4M Flash Options
Detailed view of the ESP-C3-12F KIT development board, highlighting components like the ESP-C3-12F module, AMS1117 voltage regulator, and CH340C USB-to-serial chip.
Figure 3: Detailed Component Layout of the ESP-C3-12F KIT

3. Specifications

The following table outlines the key technical specifications for the ESP-C3-12F KIT development board:

Product parameter display table in Chinese
Figure 4: Product Parameter Display (Original)
Table 1: ESP-C3-12F KIT Technical Specifications
FeatureDescription
Development Board ModelESP-C3-12F-KIT
PackageDIP-30
Dimensions (Main Module)24.0 x 16.0 x 3.1 (±0.2) mm
Antenna TypeCompatible with onboard PCB antenna / IPEX socket
Frequency Range2400 ~ 2483.5 MHz
Operating Temperature-40 °C ~ 85 °C
Storage Environment-40 °C ~ 125 °C, ≤ 90%RH
Power Supply RangeSupply voltage 5V, supply current >500mA
Supported InterfacesUART, GPIO, ADC, PWM, I2C, I2S
General IO PortsIO0, IO1, IO2, IO3, IO4, IO5, IO8, IO9, IO10, IO18, IO19, IO20, IO21
Serial Port RateSupports 110 ~ 4608000 bps, default 115200 bps
BluetoothBLE 5.0 Standard
SecurityWEP/WPA-PSK/WPA2-PSK
SPI FlashDefault 4MByte, supports 2MByte version
Onboard RGB InterfaceIO5 (Blue LED), IO3 (Red LED), IO4 (Green LED)
Dimensional drawing of the ESP-C3-12F development board with measurements in millimeters.
Figure 5: Dimensional Drawing of ESP-C3-12F Development Board

4. Setup Instructions

To begin using your ESP-C3-12F KIT development board, follow these steps:

  1. Power Supply: Connect the development board to a 5V power source via the Micro USB port. Ensure the power supply can provide at least 500mA.
  2. Driver Installation: Depending on your operating system, you may need to install a USB-to-serial driver (e.g., for the CH340C chip) to enable communication with your computer. These drivers are typically available from the chip manufacturer's website.
  3. Development Environment: Install the Espressif ESP-IDF (IoT Development Framework) or Arduino IDE with ESP32-C3 board support. Refer to the official Espressif documentation for detailed installation guides.
  4. Pinout Reference: Familiarize yourself with the board's pinout for connecting external components. The ESP-C3-12F-KIT provides 30 pins, including various GPIOs, ADC, UART, I2C, and I2S interfaces.
Pinout diagram showing the foot position of the ESP-C3-12F-Kit development board.
Figure 6: Pinout Diagram (Foot Position)

Pin Function Description:

Table 2: ESP-C3-12F KIT Pin Functions
Pin No.Function Description
1ADC_CHECK(ADC1_CH0)
2IO0 / ADC1_CH0 / XTAL_32K_N
3IO1 / ADC1_CH1 / XTAL_32K_N
4IO2 / ADC1_CH2 / FSPICLK
5IO3 / ADC1_CH3
6IO4 / ADC1_CH4 / FSPIHD / MTMS
7IO5 / ADC2_CH0 / FSPIWP / MTDI
8NC (No Connection)
9NC (No Connection)
10GND (Ground)
113V3 (Digital 3.3V power output)
12EN (Enable: High level for chip enabled; Low level for chip shutdown. Note: EN pin cannot be floating.)
13NC (No Connection)
14GND (Ground)
155V (5V power input)
163V3 (Digital 3.3V power output)
17GND (Ground)
18TX0 / IO21
19RX0 / IO20
20NC (No Connection)
21IO7 / FSPID / MTDO
22IO6 / FSPICLK / MTCK
23NC (No Connection)
24NC (No Connection)
253V3 (Digital 3.3V power output)
26IO8
27IO10 / FSPICS0
28IO9
29IO18
30IO19

5. Operating Instructions

Once the development environment is set up, you can program the ESP-C3-12F KIT:

  1. Connect to PC: Plug the Micro USB cable into the board and your computer.
  2. Select Board: In your IDE (e.g., Arduino IDE), select the appropriate ESP32-C3 board from the board manager.
  3. Select Port: Choose the serial port corresponding to your connected board.
  4. Upload Code: Write or load your desired code (e.g., a Wi-Fi scanner, a Bluetooth beacon, or a simple LED blink sketch) and upload it to the board.
  5. Monitor Serial Output: Use the serial monitor in your IDE to view debug messages or data from your program.

The onboard RGB LEDs (connected to IO3, IO4, IO5) can be used for visual feedback in your projects.

6. Maintenance

To ensure the longevity and proper functioning of your ESP-C3-12F KIT, consider the following maintenance tips:

  • Handle with Care: Avoid dropping the board or subjecting it to excessive physical stress.
  • Static Discharge: Always handle the board in an ESD-safe environment to prevent damage from static electricity.
  • Cleanliness: Keep the board free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning.
  • Power Supply: Use a stable 5V power supply within the specified current limits. Over-voltage or under-voltage can damage the components.
  • Storage: Store the board in a dry, cool place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

  • Board Not Detected: Ensure USB drivers are correctly installed. Try a different USB cable or port.
  • Upload Errors: Check if the correct board and serial port are selected in your IDE. Ensure the board is properly powered. Sometimes, pressing the boot button while connecting or uploading can help.
  • Wi-Fi/Bluetooth Issues: Verify your code for correct Wi-Fi/Bluetooth initialization and credentials. Ensure adequate power supply for wireless operations.
  • Unexpected Behavior: Double-check your wiring and code logic. Refer to Espressif's official documentation and community forums for common issues and solutions.

8. User Tips

No specific user tips were available from provided reviews or Q&A. However, general tips for ESP32-C3 development include:

  • Start Simple: Begin with basic examples like blinking an LED or connecting to Wi-Fi to verify board functionality before moving to complex projects.
  • Power Considerations: When adding many peripherals, especially power-hungry ones, consider an external 5V power supply instead of relying solely on USB.
  • Community Support: The Espressif community is very active. Utilize forums and online resources for project ideas, code examples, and troubleshooting assistance.

9. Warranty and Support

For technical support, documentation, and community resources related to the ESP32-C3 microcontroller, please visit the official Espressif website. For product-specific inquiries or issues with the ESP-C3-12F KIT development board, please contact the seller, wattie Store, directly through their platform.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.