LILYGO T-Beam NEO-6M

Contents

LILYGO® TTGO Meshtastic T-Beam V1.2 Instruction Manual

Model: T-Beam NEO-6M

Introduction

The LILYGO® TTGO Meshtastic T-Beam V1.2 is a versatile development board integrating an ESP32 microcontroller with LoRa, WiFi, Bluetooth Low Energy (BLE), and GPS capabilities. It is designed for applications requiring long-range, low-power communication, particularly for Meshtastic networks. The board also features a 0.96-inch OLED display and an 18650 battery holder for portable use.

LILYGO TTGO Meshtastic T-Beam V1.2 board with OLED display and antenna

Front view of the LILYGO TTGO Meshtastic T-Beam V1.2 board.

Specifications

The following table outlines the key technical specifications for the T-Beam V1.1 (as detailed in the provided diagrams, note that the product title refers to V1.2):

FeatureDetail
MCUESP32
Flash Memory4MB
PSRAM8MB
Serial ChipCH9102
PMU (Power Management Unit)AXP2101
Wireless ProtocolWi-Fi + Bluetooth 4.2
Onboard Functions3 Buttons (Power, IO38, Reset)
Power Supply ModeUSB / 18650 Battery
GPS ModuleNEO-6M GPS, supports GPS protocol, onboard RTC crystal, supports interrupt/wakeup
LoRa TransceiverHigh sensitivity: -148 dBm, Transceive rate: 300 kbps
LoRa Optional VersionSX1278 / SX1276
LoRa Frequency (Hardware)433MHz (SX1278), 868MHz / 915MHz / 923MHz (SX1276)
LoRa Frequency (Software)Meshtastic 433Mhz Version, Meshtastic 868/915/923 Mhz Version
OLED Size0.96 inch
OLED Resolution128 x 64 pixels
OLED Driver ICSSD1306
OLED ColorWhite
Dimensions (WxHxD)100 x 33 x 20mm
Detailed specifications table for T-Beam V1.1 Meshtastic

Detailed specifications for the T-Beam V1.1 Meshtastic board.

Package Contents

Your LILYGO TTGO Meshtastic T-Beam V1.2 package should include the following items:

  • 1 x T-Beam V1.1 CH9102 Board
  • 1 x LoRa Antenna (frequency specific)
  • 1 x 0.96 inch 128x64 OLED Display
  • 2 x 2.54mm Male Pin Headers (1*13P)

Note: If you ordered the 'Solder OLED' version, the OLED display will be pre-welded to the board.

Image showing the T-Beam board, OLED, antenna, and male pins, labeled as 'What's in the box'

Visual representation of the package contents.

Setup Instructions

  1. Antenna Installation:
    • Identify the correct LoRa antenna for your region's frequency band (e.g., 433MHz, 868MHz, 915MHz, 923MHz).
    • Carefully screw the antenna onto the SMA connector on the T-Beam board. Ensure it is finger-tight.
    Diagram showing 915/923MHz and 433/868MHz antenna types and their rotation capability

    Antenna types and rotation for optimal signal.

  2. OLED Display Installation (if not pre-soldered):
    • If you have the 'Not Solder OLED' version, align the OLED display's pins with the corresponding header on the T-Beam board (VCC, GND, SCL, SDA).
    • Gently push the OLED onto the pins. Ensure a secure connection.
    Image showing the T-Beam board and a separate OLED module, indicating where it connects

    T-Beam board with separate OLED display for installation.

  3. 18650 Battery Installation:
    • Insert a fully charged 18650 battery into the battery holder on the back of the T-Beam board.
    • Observe the polarity markings (+ and -) inside the battery holder to ensure correct insertion.
    Back view of the T-Beam board showing the 18650 battery holder

    Back view of the T-Beam board with the 18650 battery holder.

  4. Power On:
    • Press the 'Power' button on the board to turn it on. The OLED display should light up, and status LEDs may indicate activity.

Operating Instructions

  1. Meshtastic Firmware:
    • The T-Beam is designed to run Meshtastic firmware, which enables off-grid communication.
    • Refer to the official Meshtastic documentation for instructions on flashing the firmware to your device.
  2. WiFi and BLE Connectivity:
    • Once Meshtastic firmware is installed, you can connect to the T-Beam via WiFi or Bluetooth Low Energy (BLE) using the Meshtastic mobile application or desktop client for configuration and monitoring.
  3. GPS Functionality:
    • The onboard NEO-6M GPS module will attempt to acquire a satellite fix upon power-up.
    • A dedicated LED indicator (LED2) typically shows GPS working status. Position the device with a clear view of the sky for faster and more accurate fixes.
  4. Button Functions:
    • Power Button: Turns the device on/off.
    • IO38 Button: Functionality is typically defined by the loaded firmware (e.g., cycling through display screens, sending a message).
    • Reset Button: Restarts the ESP32 microcontroller.

Maintenance

  • Cleaning: Use a soft, dry cloth to clean the device. Avoid using liquids or abrasive cleaners.
  • Storage: Store the T-Beam in a cool, dry place away from direct sunlight and extreme temperatures.
  • Battery Care: If using an 18650 battery, ensure it is in good condition and charged appropriately. Do not overcharge or deep discharge the battery. Remove the battery if the device will not be used for an extended period.
  • Firmware Updates: Regularly check for and install the latest Meshtastic firmware updates to ensure optimal performance and access to new features.

Troubleshooting

  • Device not powering on:
    • Check if the 18650 battery is correctly inserted and charged, or if the USB power source is connected and functional.
    • Ensure the power button is pressed firmly.
  • OLED display not showing anything:
    • If you have the 'Not Solder OLED' version, verify that the OLED is securely connected to the pin headers.
    • Ensure the device is powered on.
  • No GPS fix:
    • Move the device to an open area with a clear view of the sky.
    • It may take several minutes for the GPS module to acquire a fix, especially on first use or after a long period of inactivity.
  • LoRa communication issues:
    • Verify that the LoRa antenna is securely attached.
    • Ensure that the correct frequency antenna is being used for your region and that the firmware is configured for that frequency.
    • Check for obstructions between devices in the Meshtastic network.
  • Firmware update failures:
    • Ensure you are using the correct flashing tool and drivers for your operating system.
    • Refer to the Meshtastic GitHub documentation for detailed flashing instructions and common issues.

User Tips

  • OLED Connection: If your package states 'Not Solder OLED', it means the OLED display is not pre-attached and needs to be manually connected to the board's pins.
  • Antenna Selection: Always ensure you select and use the antenna that matches the frequency band supported by your country and the T-Beam variant you purchased (e.g., 433MHz, 868MHz, 915MHz, 923MHz).
  • Firmware Resources: For the latest Meshtastic firmware releases and detailed guides, refer to the official Meshtastic device GitHub repository.
  • Community Support: The Meshtastic community is a valuable resource for troubleshooting and advanced usage.

Pin Diagram

The following diagram illustrates the pinout of the ESP32 TTGO T-Beam V1.1 board, providing details on GPIOs, power, and peripheral connections.

Detailed pin diagram for ESP32 TTGO T-Beam V1.1, showing GPIOs, power, LoRa, and GPS connections

Pinout diagram for the ESP32 TTGO T-Beam V1.1.

Warranty and Support

For product support, technical assistance, or warranty inquiries, please contact your seller directly. Additionally, extensive community support and documentation are available through the official Meshtastic and LILYGO GitHub repositories:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.