Gigabyte GA B460M AORUS ELITE

Contents

Gigabyte GA B460M AORUS ELITE Motherboard User Manual

Micro-ATX Intel B460 DDR4 M.2 128G Support 10th Gen LGA 1200 CPU Motherboard

1. Introduction

This manual provides detailed instructions for the installation, configuration, and maintenance of your Gigabyte GA B460M AORUS ELITE motherboard. Designed for 10th generation Intel Core, Pentium, and Celeron processors, this Micro-ATX motherboard offers robust performance and a rich feature set for various computing needs, including gaming and multimedia. Please read this manual thoroughly before proceeding with installation to ensure proper setup and operation.

Gigabyte B460M AORUS ELITE Motherboard Front Angled View
Figure 1: Front Angled View of the Gigabyte GA B460M AORUS ELITE Motherboard.

2. Specifications

FeatureDescription
Main ChipsetIntel B460
CPU Support10th Generation Intel Core / Pentium / Celeron Processors
CPU SocketLGA 1200
Memory Type4 × DDR4 DIMM slots, Dual-channel
Memory Frequency2933/2666/2400/2133MHz
Max. Memory Capacity128GB
Integrated GraphicsCPU built-in display chip (requires CPU support)
Audio ChipRealtek ALC1200 7.1 Channel Audio
Network CardIntel GbE Gigabit Network Card
PCI-E StandardPCI-E 3.0
PCI-E Slots1 × PCI-E X16 graphics slot, 1 × PCI-E X1 slot, 1 × PCI-E X4 slot
Storage Interfaces2 × M.2 interface, 6 × SATA III interface
USB (Back Panel)1 × Type-C (USB 3.2 Gen 1), 3 × USB 3.2 Gen1, 2 × USB 2.0/1.1
USB (Internal)2 × USB 3.2 Gen1, 4 × USB 2.0/1.1
Video Interfaces1 × DVI, 1 × DisplayPort, 1 × HDMI
Power Connectors1 × 8-pin, 1 × 24-pin
Other Interfaces1 × PS/2 keyboard/mouse, 1 × RJ45 network, 6 × Audio interfaces
Form FactorMicro ATX (24.4 × 24.4 cm)
BIOS128 Mbit flash, AMI UEFI BIOS, PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0
RAID SupportRAID 0, 1, 5, 10
OverclockingNot Supported
Hardware MonitoringVoltage, temperature, fan speed detection, over-temperature warning, fan failure warning, intelligent fan control
Gigabyte B460M AORUS ELITE Motherboard Rear I/O Panel Layout
Figure 2: Rear I/O Panel of the Gigabyte GA B460M AORUS ELITE Motherboard, showing various ports.

3. Setup and Installation

3.1 Safety Precautions

  • Always disconnect the power cord from the wall outlet before installing or removing any components.
  • Wear an anti-static wrist strap or frequently touch a grounded metal object to prevent electrostatic discharge (ESD) damage.
  • Handle components by their edges, avoiding contact with pins or circuitry.

3.2 Component Identification

Familiarize yourself with the layout of the motherboard. Key areas include the CPU socket (LGA 1200), DDR4 DIMM slots, PCI-E slots, M.2 slots, SATA ports, and various headers for front panel connectors.

Gigabyte B460M AORUS ELITE Motherboard Close-up of CPU Socket
Figure 3: Close-up view of the LGA 1200 CPU socket and surrounding components.

3.3 CPU Installation

  1. Open the CPU socket lever.
  2. Carefully align the CPU with the socket, ensuring the triangular mark on the CPU matches the mark on the socket. Do not force the CPU into place.
  3. Close the socket lever to secure the CPU.
  4. Install the CPU cooler according to its manufacturer's instructions.

3.4 Memory (RAM) Installation

  1. Open the clips at both ends of the DIMM slot.
  2. Align the notch on the DDR4 memory module with the key on the DIMM slot.
  3. Insert the memory module firmly into the slot until the clips snap into place. For dual-channel configuration, refer to the motherboard's specific slot pairing (usually alternating slots).

3.5 Storage Device Installation (M.2 / SATA)

M.2 SSD:

  1. Locate the M.2 slots on the motherboard.
  2. Remove the M.2 standoff screw.
  3. Insert the M.2 SSD into the slot at an angle.
  4. Gently push down the SSD and secure it with the standoff screw.

SATA Drives:

  1. Connect one end of the SATA data cable to a SATA III port on the motherboard.
  2. Connect the other end of the SATA data cable to your HDD/SSD.
  3. Connect a SATA power cable from your power supply to the HDD/SSD.

3.6 Power Connections

  1. Connect the 24-pin ATX main power connector from your power supply to the corresponding port on the motherboard.
  2. Connect the 8-pin ATX 12V CPU power connector to the port near the CPU socket.

3.7 Case Mounting and I/O Shield

  1. Install the I/O shield into the rear opening of your computer case.
  2. Carefully place the motherboard into the case, aligning the screw holes with the standoffs.
  3. Secure the motherboard with screws.
  4. Connect front panel headers (power button, reset button, USB ports, audio jacks) to their respective pins on the motherboard. Refer to the motherboard diagram for correct pin assignments.
Gigabyte B460M AORUS ELITE Motherboard Various Connectors and Ports
Figure 4: Overview of various connectors and ports on the motherboard.

4. Operating Instructions

4.1 First Boot

After assembling all components and connecting power, press the power button on your PC case. The system should initiate the boot process. If no display appears, refer to the troubleshooting section.

4.2 BIOS/UEFI Setup

To enter the BIOS/UEFI setup utility, press the DEL key repeatedly during the initial boot sequence. Here you can configure system settings, boot order, and monitor hardware status. The BIOS is an AMI UEFI BIOS with PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, and ACPI 5.0 support.

4.3 Driver Installation

After installing your operating system, install the necessary drivers for the chipset, audio (Realtek ALC1200), and network (Intel GbE) from the Gigabyte official website or the included driver disk (if applicable) to ensure optimal performance and functionality.

5. Maintenance

5.1 Cleaning

  • Regularly clean dust from inside your PC case using compressed air.
  • Ensure fans (CPU cooler, case fans) are free from obstructions.
  • Do not use liquid cleaners directly on motherboard components.

5.2 BIOS Updates

Periodically check the Gigabyte official website for BIOS updates. BIOS updates can improve system stability, compatibility, and performance. Follow the instructions provided by Gigabyte carefully when performing a BIOS update to avoid system damage.

6. Troubleshooting

6.1 No Power/No Boot

  • Check all power connections (24-pin ATX, 8-pin CPU, GPU, SATA).
  • Ensure the power supply is switched on.
  • Verify that the front panel power button is correctly connected to the motherboard.
  • Try booting with minimal components (CPU, one RAM stick, GPU if no integrated graphics) to isolate the issue.

6.2 No Display

  • Ensure your monitor is connected to the correct video output (motherboard I/O for integrated graphics, or dedicated GPU).
  • Check that the display cable is securely connected at both ends.
  • Reseat your RAM modules and graphics card.

6.3 Component Not Detected

  • For RAM, ensure modules are fully seated in their slots.
  • For M.2/SATA drives, check connections and ensure they are enabled in BIOS.
  • Ensure all necessary drivers are installed for your operating system.

7. User Tips

While no specific user tips were available from the provided reviews or Q&A, general best practices for motherboard usage include:

  • Always refer to the official Gigabyte website for the latest drivers and BIOS updates.
  • Ensure adequate airflow within your PC case to maintain optimal operating temperatures for all components.
  • When installing components, apply gentle but firm pressure. Never force components into place.

8. Warranty and Support

For warranty information, please refer to Gigabyte's official warranty policy available on their website. Support resources, including FAQs, driver downloads, and contact information, can also be found on the official Gigabyte support page.

A user manual in PDF format is available for this product. For detailed diagrams and further technical information, please contact the seller to obtain the official user manual PDF. The PDF manual can be referenced at: Gigabyte GA B460M AORUS ELITE User Manual (PDF)

© 2024 Gigabyte. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.