Aigo AR12PRO

Contents

Aigo AR12PRO 120mm RGB Fan Instruction Manual

Model: AR12PRO | Brand: Aigo

1. Introduction

The Aigo AR12PRO is a high-performance 120mm cooling fan designed for computer cases and radiators. It features Addressable RGB (ARGB) lighting with an aurora effect, offering a wide range of colorful choices to enhance your PC's aesthetics. Equipped with Pulse Width Modulation (PWM) control, it allows for precise fan speed adjustments to optimize cooling performance and noise levels. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your Aigo AR12PRO fan.

Video: Aigo AR12PRO Product Showcase and RGB Effects

2. Safety Information

  • Always disconnect power from your computer before installing or handling any internal components.
  • Handle the fan and cables with care to avoid damage.
  • Ensure proper grounding to prevent electrical hazards.
  • Keep the fan away from liquids and excessive moisture.
  • Do not attempt to open or modify the fan or controller, as this may void the warranty and cause damage.
  • Keep out of reach of children.

3. Package Contents

The contents of your Aigo AR12PRO package may vary depending on the kit purchased (e.g., single fan, 3-in-1 kit, 5-in-1 kit, etc.). A typical package for a single fan includes:

  • Aigo AR12PRO 120mm Fan
  • Mounting Screws

If you purchased a kit that includes a controller (e.g., ACP1 ARGB controller), the package will also contain:

  • ACP1 ARGB Controller
  • 5V RGB Signal Cable (approx. 500mm)
  • PWM Signal Cable (approx. 500mm)
  • Remote Control (Note: Battery for remote control may be removed for customs inspection)
  • Double-sided Velcro for controller mounting
AR12PRO single fan with 5V A-RGB and PWM 4 Pin connectors

Image: AR12PRO single fan with its 5V A-RGB and PWM 4 Pin connectors.

Aigo ARGB Controller and included accessories: 5V RGB Signal Cable, PWM Signal Cable, Remote Control, and Double Side Velcro.

Image: Aigo ARGB Controller and included accessories: 5V RGB Signal Cable, PWM Signal Cable, Remote Control, and Double Side Velcro.

4. Specifications

FeatureSpecification
Model NumberAR12PRO
Fan Size120 x 120 x 25 mm
Weight180g
Fan Speed800 - 1600 (±20%) RPM
Noise Level28.6 dBA (Max)
Air Volume74 CFM (Max)
Wind Pressure2.2 mmH2O (Max)
Bearing TypeFluid Bearing
Voltage12V
Rated Power4.2W
Current0.16A
Fan Life Span100,000 hours
Power InterfaceARGB 3PIN + PWM 4PIN
Blade Quantity9
Used ForCase, Radiator
CertificationCE, FCC, RoHS
Diagram showing the dimensions of the Aigo AR12PRO fan: 120mm width, 120mm height, and 25mm thickness.

Image: Dimensions of the Aigo AR12PRO fan.

Controller Specifications (ACP1 ARGB Controller, if included)

FeatureSpecification
Dimensions10 cm (Length) x 4.6 cm (Width) x 1.4 cm (Height)
Power InputSATA Power Connector
Fan PortsMultiple ARGB and PWM ports (typically up to 10 each)
Motherboard SyncRESET/MBPWM SYNC port for 5V ARGB motherboard control
Diagram showing the dimensions of the Aigo ARGB controller: 10cm length, 4.6cm width, and 1.4cm height.

Image: Dimensions of the Aigo ARGB controller.

5. Setup and Installation

5.1 Fan Interface Overview

The Aigo AR12PRO fan uses two main types of connectors:

  • 4PIN PWM Connector: For fan speed control. Connects to your motherboard's 4-pin fan headers or a fan controller.
  • 5V A-RGB 3pin Connector: For Addressable RGB lighting control. Connects to your motherboard's 5V ARGB header or an ARGB controller.
Diagram illustrating the 4PIN PWM Male/Female and 5v A-RGB 3pin Male/Female fan interface connectors.

Image: Fan Interface Connectors (4PIN PWM and 5V A-RGB 3pin).

5.2 Fan Mounting

Mount the AR12PRO fans to your PC case or radiator using the provided screws. Ensure the fan is oriented correctly for desired airflow (intake or exhaust).

Diagram showing airflow direction: cold wind entering the fan from the front and hot air exiting from the back.

Image: Airflow direction indicator. The front is the air inlet, the back is the air outlet.

5.3 Fan Connection Steps (Tandem/Daisy Chain)

The AR12PRO fans are designed for easy series connection (daisy-chaining) for both PWM and ARGB signals.

  1. PWM Connection: Connect the 4PIN PWM Male connector of one fan to the 4PIN PWM Female connector of the next fan. The last fan in the chain will connect its 4PIN PWM Male connector to your motherboard's PWM header or a fan controller.
  2. ARGB Connection: Connect the 5V A-RGB 3pin Male connector of one fan to the 5V A-RGB 3pin Female connector of the next fan. The last fan in the chain will connect its 5V A-RGB 3pin Male connector to your motherboard's 5V ARGB header or an ARGB controller.
Diagram showing how to connect multiple fans in tandem using 4PIN PWM and 5V A-RGB 3pin connectors. The former fan connects in series with the latter fan, so the cycle overlaps.

Image: Fan connection steps for tandem setup.

Close-up view of two fans connected in series, showing the 4PIN PWM and 5V 3PIN INTERFACE connections.

Image: Detailed view of series connection for PWM and ARGB interfaces.

5.4 Controller Connection (If using ACP1 ARGB Controller)

If your motherboard does not have a 5V ARGB header or you prefer external control, use the ACP1 ARGB controller:

  1. Power Connection: Connect the SATA power connector from your PC's power supply to the SATA INPUT PORT on the controller.
  2. Fan Connections: Connect the 4PIN PWM Male connectors from your fans (or the last fan in a daisy chain) to the PWM ports on the controller. Connect the 5V A-RGB 3pin Male connectors from your fans (or the last fan in a daisy chain) to the ARGB ports on the controller.
  3. Motherboard Sync (Optional): If your motherboard has a 5V ARGB header, you can connect the controller's RESET/MBPWM SYNC port to it using the provided 5V RGB Signal Cable to synchronize lighting effects with your motherboard software.
  4. Remote Control: The remote control allows you to change lighting modes and fan speeds. Ensure the remote has a working battery (if not included, install a CR2025 button cell battery).
Overview of the Aigo ARGB controller showing ARGB, PWM, SATA, and RESET/MBPWM SYNC ports.

Image: Aigo ARGB Controller with labeled ports.

Aigo ARGB controller connected with cables and remote control shown.

Image: Aigo ARGB controller with connected cables and remote.

Aigo ARGB controller showing the adhesive gum for mounting.

Image: Aigo ARGB controller with adhesive gum for mounting.

6. Operation

6.1 Fan Speed Control (PWM)

The AR12PRO fans support PWM, allowing your motherboard or fan controller to dynamically adjust fan speed based on system temperature. This ensures efficient cooling when needed and quiet operation during lighter loads.

  • If connected to a motherboard PWM header, fan speed can be controlled via BIOS settings or motherboard software.
  • If connected to an Aigo controller, fan speed can be adjusted using the remote control or compatible software (if available).

6.2 ARGB Lighting Control

The Addressable RGB lighting provides a wide array of customizable effects.

  • Motherboard Sync: If connected to a 5V ARGB header on your motherboard, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync).
  • Controller Control: If using the Aigo ARGB controller, you can change lighting modes, colors, and brightness using the included remote control.

7. Maintenance

Regular maintenance helps ensure optimal performance and extends the lifespan of your Aigo AR12PRO fans.

  • Cleaning: Periodically clean the fan blades and frame to remove dust buildup. Use a soft brush or compressed air. Ensure the fan is powered off and disconnected before cleaning.
  • Inspection: Check cables for any signs of wear or damage. Ensure all connections are secure.
  • Shock Absorption: The fan features a soft material damping pad for shock absorption. Ensure these pads are intact for silent operation.
Close-up of the 9-blade design with screw threads, optimized for air duct efficiency.

Image: Detail of the 9-blade design, optimized for airflow.

Image highlighting the shock absorption design of the fan, with damping pads around the frame.

Image: Shock absorption design for silent operation.

8. Troubleshooting

  • Fan Not Spinning:
    • Check if the 4PIN PWM connector is securely plugged into the motherboard or controller.
    • Ensure the power supply is providing power to the fan/controller.
    • Verify that fan control settings in BIOS or software are not set to 0 RPM.
  • RGB Lighting Not Working/Syncing:
    • Ensure the 5V A-RGB 3pin connector is securely plugged into the motherboard's ARGB header or the controller.
    • If using a controller, check its power connection (SATA) and ensure the remote control battery is functional.
    • If using motherboard sync, ensure your motherboard has a 5V ARGB header (not 12V RGB) and that the correct software is installed and configured.
    • Verify that the ARGB cables are connected in the correct orientation.
  • Fan Speed Not Adjustable:
    • Confirm the 4PIN PWM connector is properly connected.
    • Check BIOS settings or fan control software for proper configuration.
    • If using a controller, ensure it supports PWM control and that the remote control is functioning.
  • Remote Control Not Working:
    • Check and replace the remote control battery (CR2025 button cell). Note: Battery may be removed for customs.
    • Ensure there are no obstructions between the remote and the controller.

9. User Tips

  • Controller Choice: If your motherboard lacks a 5V ARGB sync interface, a dedicated ARGB controller is necessary to manage lighting effects. Be aware that some third-party controllers may only adjust lighting and not fan speed.
  • Motherboard Compatibility: Always confirm your motherboard has a 5V 3-pin ARGB header for direct lighting synchronization. Do not connect 5V ARGB devices to 12V RGB headers, as this can cause damage.
  • Daisy Chaining: The fans are designed for easy daisy-chaining. Connect them in series to simplify cable management and reduce the number of ports needed on your motherboard or controller.

10. Warranty and Support

The Aigo AR12PRO fan comes with a 1-year warranty for the fan and CPU radiator components. For any issues or support inquiries, please contact the Aigo Official Store or your retailer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.