EUDAX QF-1694-7T, QF-1688R-3

Contents

4CH RC Remote Control Circuit PCB Transmitter and Receiver Board Instruction Manual

Model: QF-1694-7T (Transmitter) / QF-1688R-3 (Receiver)

Introduction

This manual provides instructions for the 4-channel (4CH) RC Remote Control Circuit PCB Transmitter and Receiver Board system. This system is designed for DIY hobby car toys, allowing for remote control of movement (forward, backward, left, right). Please read these instructions carefully before assembly and operation to ensure proper functionality and safety.

Video: Product demonstration showing the RC circuit boards and their application in a DIY car.

Specifications

Component Detail
Transmitter Board Model QF-1694-7T
Receiver Board Model QF-1688R-3
Frequency 27MHz / 40MHz (as indicated on boards)
Transmitter Power Supply 3V (2 x AA batteries)
Receiver Power Supply 6V (4 x AA batteries)
Transmitter Board Dimensions 5.6cm (2.20in) x 3.8cm (1.50in)
Receiver Board Dimensions 4.1cm (1.610in) x 2.7cm (1.061in)
Recommended Age 14+ years
Origin Mainland China
Package Weight 0.03 kg
Package Dimensions 15cm (Length) x 20cm (Width) x 2cm (Height)

Note: All products are shipped without batteries. Motors and battery holders are not included with the circuit boards.

Setup Instructions

Careful wiring is crucial for the correct operation of your RC system. Please follow the diagrams below for connecting the transmitter and receiver boards.

1. Transmitter Board (QF-1694-7T) Wiring

Transmitter board wiring diagram

Image: Transmitter board (QF-1694-7T) showing connections for 3V power (2xAA battery) and control inputs for Forward/Backward and Right/Left. An antenna is also connected.

  • Power Supply: Connect a 3V power source (e.g., 2 x AA batteries) to the B+ (positive) and B- (negative) terminals. Ensure correct polarity.
  • Antenna: Connect the antenna wire to the designated ANT terminal.
  • Control Inputs: The board features contact points for controlling movement. These are typically connected to switches or buttons that, when pressed, complete a circuit to send the respective command (Forward, Backward, Right, Left).

2. Receiver Board (QF-1688R-3) Wiring

Receiver board wiring diagram

Image: Receiver board (QF-1688R-3) showing connections for 6V power (4xAA battery) and motor outputs for Right/Left and Forward/Backward. An antenna is also connected. Note that motors and battery holders are not included.

  • Power Supply: Connect a 6V power source (e.g., 4 x AA batteries) to the B+ (positive) and B- (negative) terminals. Ensure correct polarity.
  • Antenna: Connect the antenna wire to the designated ANT terminal.
  • Motor Connections:
    • Green/Yellow Wires: Connect to the motor responsible for Right/Left steering.
    • Blue/White Wires: Connect to the motor responsible for Forward/Backward movement.
    Ensure motors are correctly wired for desired direction. If a motor spins in the opposite direction, reverse its two wires.
Transmitter and receiver boards overview

Image: Overview of both the transmitter and receiver boards with their respective wiring.

Operating Instructions

Once both the transmitter and receiver boards are correctly wired and powered, you can operate your DIY RC toy.

  1. Ensure both the transmitter and receiver have their respective power sources connected and turned on (if applicable).
  2. Use the control inputs on the transmitter board to send commands:
    • Forward: Activate the 'Forward' control on the transmitter. The corresponding motor on the receiver should drive the toy forward.
    • Backward: Activate the 'Backward' control on the transmitter. The corresponding motor on the receiver should drive the toy backward.
    • Right: Activate the 'Right' control on the transmitter. The steering motor on the receiver should turn the toy right.
    • Left: Activate the 'Left' control on the transmitter. The steering motor on the receiver should turn the toy left.
  3. Observe the toy's response. If movements are incorrect, refer to the Troubleshooting section.
RC car application example

Image: An example of the RC circuit boards integrated into a DIY car chassis, demonstrating a typical application.

Maintenance

  • Keep Dry: Protect the circuit boards from moisture and liquids to prevent short circuits and damage.
  • Cleanliness: Keep the boards free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Battery Care: Remove batteries from both the transmitter and receiver if the toy will not be used for an extended period to prevent leakage.
  • Handle with Care: Avoid dropping or subjecting the boards to strong impacts, which can damage components or solder joints.

Troubleshooting

Problem Possible Cause Solution
Toy does not respond to controls.
  • No power to transmitter or receiver.
  • Incorrect battery polarity.
  • Loose or incorrect wiring.
  • Interference.
  • Check batteries in both units and replace if dead.
  • Verify battery polarity (+/-).
  • Inspect all wire connections for looseness or incorrect placement.
  • Move to an area with less radio interference.
Motor spins in the wrong direction. Motor wires connected with reversed polarity. Reverse the two wires connected to the affected motor.
Limited control range.
  • Antenna not fully extended or damaged.
  • Weak batteries.
  • Ensure antennas are fully extended and undamaged.
  • Replace batteries in both units.

User Tips

  • Double-Check Polarity: Always verify battery and motor wire polarity before powering on to prevent damage to the circuit boards.
  • Secure Connections: Ensure all wire connections are firm and insulated to avoid accidental shorts.
  • Test Before Final Assembly: It's recommended to test the circuit boards with motors and power supplies before integrating them into your final DIY project.
  • Antenna Placement: For optimal range, ensure the antennas on both the transmitter and receiver are positioned as straight and unobstructed as possible.

Warranty and Support

For any questions, technical assistance, or issues not covered in this manual, please contact the seller directly through the platform where you purchased the product. Provide your order details and a clear description of the issue for prompt support.

This product is intended for educational and hobby use. The manufacturer is not responsible for damage caused by improper use, modification, or assembly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.