Allsome BG-5157

Contents

Allsome 6-Speed Benchtop Drill Press User Manual

Model: BG-5157 | 1200W

Important Safety Instructions

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. SAVE THESE INSTRUCTIONS.

Work Area Safety

  • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
  • Keep the floor around the machine clean and free of scrap material, oil, and grease.
  • Do not operate the drill press in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Machine creates sparks which may ignite the dust or fumes.
  • Keep bystanders, children, and visitors away while operating a machine. Distractions can cause you to lose control.

Electrical Safety

  • Before plugging in the machine, be certain the outlet voltage supplied is within the voltage marked on the nameplate.
  • Make sure the machine is properly grounded.
  • Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.
  • Do not expose this drill press to rain or wet conditions. Water entering a machine will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord to carry the machine or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

Product Specifications

Feature Specification
Brand NameAllsome
Model NumberBG-5157
Rated Voltage220V
Frequency50/60Hz
Input Power1200W
No-load Speed350-950 r/min
Max. Drilling Diameter16mm
Max Spindle Travel60mm
ApplicationBench Drill, Home DIY, Wood & Metal Drilling
Weight13.4KG
Power SourceAC
MovableYes
HandheldNo

Dimensions

Diagram showing the dimensions of the drill press. One view shows a height of 35cm, depth of 15cm, and base width of 32cm. Another view shows a total height of 60cm and base width of 20cm.
Figure 1: Drill Press Dimensions

Setup and Assembly

Shipping Contents

Unpack the carton and verify that all parts listed below are included. Refer to the user manual PDF for a visual representation of the shipping contents.

Image showing the Allsome Benchtop Drill Press along with various accessories like drill bits, wrenches, and a cross slide table.
Figure 2: Typical contents of the package, including the drill press and accessories.

Column Assembly

  1. Place the base on a level floor.
  2. Place the column (part 77) on the base (part 74).
  3. Using the attached 6mm Hex Key, tighten the three Hex Bolts on the base.

Assembly Feed Handle

Screw the Feed Handle into the Feed Shaft (part 81), and tighten it.

Operating Instructions

WARNING: Unplug the machine from the power source before making any adjustment.

Adjusting the Guide Play

If the bench drill guide has too much or too little play, it can be reset using the adjusting screws. First, release the nut, then set the play using the set screw. Lock by re-tightening the nut. Do not over-tighten the set screws as the guide will be damaged.

Raise or Lower the Head

This machine can be raised or lowered in small increments by using the elevator mechanism.

  1. Loosen two lock levers (part 47).
  2. Loosen two screws (part 40) of the elevator (part 61).
  3. Lift or lower the head and elevator to the desired height.
  4. Tighten the lock levers firmly again.

For larger adjustments, the head can be moved up or down by rotating the elevator wheel after loosening the lock lever (part 47). The desired height is indicated by the depth point.

Image showing the handle of the drill press being operated, with red arrows indicating the range of motion for raising and lowering the drill head.
Figure 3: Operating the feed handle to adjust drill head position.

Adjusting the Depth Stop

  1. Loosen the fixed screw (part 34) of the depth point.
  2. Feed down the handle and let the drill bit touch the workpiece.
  3. Adjust the point (part 35) to the desired depth.
  4. Tighten the fixed screw again.

Changing Spindle Speed

This drill press is designed to adjust the output speed by an electronic speed controller (part 10).

Close-up image of the drill press control panel, showing the red On/Off switch and a speed dial with settings from 1 to 6.
Figure 4: Control panel with On/Off switch and speed dial.
  • Rotate the Adjustment Knob down or forward (towards '+') for higher speed.
  • Rotate the Adjustment Knob up or backward (towards '-') for lower speed.

Installing Drills

Insert the drill bit into the chuck jaws with about 10mm insertion. When using a small drill, do not insert it so far that the jaws touch the flutes of the drill. Make sure the drill bit is centered in the chuck before tightening the chuck with the key.

To tighten the chuck, insert the key into each of the three key holes in succession and tighten clockwise firmly. The chuck can be released by using one hole only.

Image of the drill press in operation, drilling into a metal workpiece, with metal shavings visible on the base.
Figure 5: Drill press in operation.

Maintenance

WARNING: Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all machine service be performed by a Factory Authorized Service Station.

Tool Lubrication

Your machine has been properly lubricated and is ready to use. It is recommended that machines with gears be regreased with a special gear lubricant at every brush change.

Carbon Brushes

The brushes and commutator in your machine have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend examining the brushes every 50 hours of operation. Only genuine replacement brushes specially designed for your machine should be used.

Cleaning

WARNING: To avoid accidents, always disconnect the machine from the power supply before cleaning or performing any maintenance.

The machine may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air. Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

Troubleshooting

This section provides general guidance for common issues. For detailed troubleshooting, please refer to the official user manual PDF.

  • Excessive Vibration or Runout: Ensure all components are securely fastened and the drill bit is properly centered in the chuck. Check for any loose parts or damage.
  • Reduced Drilling Performance: Verify the correct spindle speed is selected for the material and drill bit size. Ensure the drill bit is sharp and appropriate for the task.
  • Motor Overheating: Avoid continuous heavy-duty operation without breaks. Ensure ventilation openings are clear of debris.
  • Power Issues: Check the power connection and ensure the outlet voltage matches the machine's requirements (220V).

While this drill press is robust, it is primarily designed for drilling. For milling operations, especially light ones, specialized milling machines are recommended to prevent premature wear or damage.

User Tips

  • This drill press is noted for its sturdy construction and minimal vibration, making it suitable for precise drilling in various materials.
  • Users have found it effective for drilling thick materials due to its high power and stable operation.
  • Ensure the machine is securely mounted or fastened to a workbench for optimal stability and safety, especially when working with larger drill bits or tougher materials.
  • While capable, exercise caution when using larger drill bits (e.g., 24mm) and adjust speed accordingly.
  • The speed adjustment feature is crucial for adapting to different materials and drill bit sizes, contributing to better results and tool longevity.

Warranty and Support

For detailed warranty information, technical support, or to access the complete exploded view and parts list, please refer to the official user manual PDF or contact the seller directly.

Official User Manual (PDF): Download PDF Manual

Parts List

The following table lists the components of the drill press. For a visual exploded view, please refer to the official PDF manual.

No. Part Name No. Part Name
1Screw ST4x1246Copper Bent Sheet
2Rare Cover47T Wrench
3Cord Anchor48Screw M4x8
4Cord Sleeve49Circlip for shaft 12
5Cord50Coil Spring Cover
6Screw M4x1451Coil Spring
7Connector52Screw M4x6
8Housing53Elevator Gear
9On/Off Switch54Spring
10Speed Controller55Circlip for shaft 8
11Carbon Brush56Flat Washer 8
12Brush Holder57Nut Tr12
13Brush Cap58Thread Bar Tr12
14Stator59Screw M5x8
15Screw ST5x6560Bearing Cover
16Air Deflector61Screw M6x30
17Bear 60862Cone Gear
18Armature63Flat Washer 4
19Bearing 600064Screw M4x6
20Chuck B1665Cover
21Hex Nut M18x1.566Side Cover
22Spindle67Circlip for hole 22
23Woodruff KeyB468Column Pin Ø3x10
24Circlip for hole 4069Hand Wheel Shaft
25Washer Ø3970Hand Wheel
26Bearing 620371Screw M8
27Circlip for shaft 1772Hand Wheel Handle
28Screw ST5x4073Screw M5x51
29Gear Box74Base
30Gear75Tube Fixed Supporter
31Circlip for shaft 1476Screw M8x20
32Middle Gear77Tube Ø45
33Middle Cover78Handle Ball
34Screw M4x1279Top Cover of tube
35Pointer80Feed Handle
36Nut M481Feed Shaft
37Stop Rod82Column Pin Ø4x12
38Slide Block83Scale
39Guide Rod84Slide Body
40Elevator85Nut M8
41Screw M5x586Slide Block Cover
42Screw M6x1687Screw M4x10
43Rack88Chuck Key B16
44Screw M4x1489Screw M5x16
45Copper Straight Sheet90

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.