FDIK Plastic 2KW

Contents

FDIK 12V 2KW Diesel Air Parking Heater

Model: Plastic 2KW

Brand: FDIK

1. Introduction

The FDIK 12V 2KW Diesel Air Parking Heater is an independent heating device designed to provide warmth in various vehicles and environments without needing to start the engine. It features a compact design, efficient heating, and user-friendly controls, making it suitable for cars, buses, trailers, RVs, boats, and even small greenhouses.

FDIK 2KW 12V Diesel Air Parking Heater with digital controller
Figure 1.1: FDIK 2KW 12V Diesel Air Parking Heater with digital controller.

This heater operates on diesel fuel and a 12V power supply, delivering 1000-2000W of thermal power. Its design emphasizes silence, oil-saving, and intelligent constant temperature control, ensuring a comfortable and safe heating experience. The unit incorporates high-quality materials, including a plastic shell (PA6 and GF30 environmental protection materials) and an aluminum shell, designed to be mute and odor-free.

Diagram showing how the parking heater works in a car
Figure 1.2: Operational diagram of the parking heater installed in a vehicle.

The independent heating system preheats the cab in cold environments, providing convenience and comfort. It is equipped with an NTC temperature sensor for accurate temperature sensing and overheating protection for enhanced safety.

Applications for 12V and 24V heaters including cars, boats, greenhouses, trucks, buses, and RVs
Figure 1.3: Examples of 12V applications (car, boat, greenhouse) and 24V applications (truck, bus, RV).

2. Safety Information

Please read and understand all safety warnings and instructions before installing and operating this heater. Failure to follow these instructions may result in fire, explosion, electric shock, or other hazards, leading to property damage, personal injury, or death.

General Safety Precautions:

  • Ensure the heater is installed in a well-ventilated area if used indoors, to prevent carbon monoxide poisoning.
  • Do not operate the heater near flammable liquids, gases, or other combustible materials.
  • Keep children and pets away from the heater during operation.
  • Ensure all electrical connections are secure and correctly wired to prevent short circuits or electrical fires.
  • Use only diesel fuel. Do not use gasoline or other fuels, as this can cause fire or damage to the unit.
  • Do not block the air inlet or outlet of the heater. Maintain adequate clearance for proper airflow.
  • Regularly inspect the exhaust system for leaks or damage.
  • In case of malfunction, turn off the heater immediately and consult a qualified technician.
  • This heater is designed for 12V systems. Do not connect it to a 24V system unless you have a 24V specific model.

3. Package Contents

Carefully unpack the box and ensure all items listed below are present and undamaged. If any parts are missing or damaged, contact your seller immediately.

Detailed list of accessories included with the FDIK diesel air parking heater
Figure 3.1: Included accessories and main unit.

Included Components:

  • Heater Host Unit
  • Controller (Digital Display)
  • Remote Control
  • Exhaust Pipe
  • Tubing (Air Ducts)
  • 5L Fuel Tank
  • Oil Pump (Electromagnetic Pump)
  • Wire Harness
  • Wind Head (75mm or 60mm, depending on variant)
  • Air Filter
  • Oil Filter
  • Rubber Pad
  • Fixed Plate
  • Oil Pump Clamp
  • Screw Accessory Kit (various screws, clamps, washers)
  • User Manual (may be in Russian or English)

4. Specifications

Below are the technical specifications for the FDIK 12V 2KW Diesel Air Parking Heater.

Diagram showing product dimensions and key specifications
Figure 4.1: Product dimensions and key specifications.
FeatureSpecification
Brand NameFDIK
Model NamePlastic 2KW
Item TypeHeating & Fans
Voltage12V
Power (W)1000W - 2000W (Adjustable)
Fuel TypeDiesel
Special FeaturesAir heating, Overheating protection, Intelligent constant temperature
Switch TypeRotary switch (on controller)
MaterialPlastic + Aluminum
Item Length33.5 cm
Item Width11.5 cm
Item Height12 cm
Item Diameter6 cm (Air outlet)
Item Weight4.8 kg
Package Weight4.9 kg
Operating Temperature-40°C to 40°C
Air Volume60-90 m³/h
External Testing CertificationCE
Exploded view diagram of the heater's internal components
Figure 4.2: Internal components diagram.
Detailed breakdown of key components: Motor Assembly, Glow Plug, Combustion Chamber, Oil Pump
Figure 4.3: Detailed component breakdown.

5. Installation and Setup

Proper installation is crucial for the safe and efficient operation of your parking heater. If you are unsure about any step, consult a professional.

5.1 Choosing an Installation Position

Select a location that allows for secure mounting, proper air circulation, and safe routing of fuel and exhaust lines. Avoid areas where the heater could be exposed to excessive moisture or impact.

Installation Diagram showing wiring and oil pump angle, and Installation Position examples for various vehicles
Figure 5.1: Installation Diagram and suggested positions.
  • Truck: On the co-driver's legroom, on the rear wall of the cab, driver's seat backrest, or under the toolbox.
  • RV: In front of the passenger seat, between the driver's seat and passenger seat, under the container, or in the trunk.
  • 5 Seater / 7 Seater: Mainly installed in the passenger room or luggage room. If unable to install, fix under the underside of the vehicle, but beware of splashing.
  • Excavator: Inside the driver's seat or on the back wall of the cab, inside the protection box.

5.2 Wiring Diagram

Follow the wiring diagram carefully. Ensure all connections are tight and insulated.

Installation Diagram showing wiring connections
Figure 5.2: Wiring connections for the heater. The positive and negative main wires must be connected to the battery for normal operation of the main unit.
  • Connect the positive (+) and negative (-) main wires directly to the vehicle's 12V battery.
  • Connect the switch and control unit as per the diagram.
  • Ensure the air inlet and air outlet are reserved for proper airflow.

5.3 Fuel System Connection

The heater uses diesel fuel. Connect the oil pump and fuel tank as shown in the diagram.

Diagram illustrating air intake, hot air exhaust, diesel fuel input, and fumes exhaust connections
Figure 5.3: Air, fuel, and exhaust connections.
  • Install the oil pump at an angle between 15° and 35° for optimal performance.
  • Ensure the oil filter is installed correctly in the fuel line.
  • Connect the fuel tank to the oil pump, and the oil pump to the heater's fuel inlet.

5.4 Exhaust System

Route the exhaust pipe safely away from any flammable materials and passenger compartments. Ensure there are no leaks.

5.5 Air Ducts

Connect the air intake and hot air outlet ducts. Ensure they are clear of obstructions and routed to effectively heat the desired space.

6. Operation

The FDIK parking heater can be operated via its digital controller or the included remote control.

FDIK LCD Switch and remote control, showing temperature and power adjustment
Figure 6.1: Digital controller and remote control.

6.1 Initial Start-up (Priming the Fuel Line)

Before the first use or after running out of fuel, the fuel line needs to be primed to ensure the oil pump delivers fuel to the heater. Refer to your specific manual for the exact priming procedure, which usually involves a sequence of button presses on the controller to activate the oil pump without ignition.

6.2 Turning On/Off

  • To Turn On: Press and hold the power button on the digital controller or the remote control. The heater will go through a start-up sequence, including glow plug preheating and fan activation, before ignition.
  • To Turn Off: Press and hold the power button again. The heater will enter a cool-down cycle to prevent overheating, during which the fan will continue to run for a few minutes before shutting down completely. Do not disconnect power during the cool-down cycle.

6.3 Adjusting Temperature and Power

Diagram illustrating adjustable power and temperature settings
Figure 6.2: Power and temperature adjustment.

The heater offers two main operating modes: power level adjustment and temperature control.

  • Power Mode: Adjust the heating power (1000W to 2000W) using the rotary switch or corresponding buttons on the controller/remote. This mode allows for 5 levels of power adjustment.
  • Temperature Control Mode: Set a desired temperature between 16°C and 35°C. The heater will automatically adjust its output to maintain the set temperature.

Use the rotary switch on the controller or the +/- buttons on the remote to cycle through modes and adjust settings. The LCD display will show the current temperature or power level.

6.4 Remote Control Functions

The remote control allows for convenient operation from a distance. It can control temperature, power, and may include a timing function for scheduled operation. Ensure the remote is paired with the heater (refer to troubleshooting for pairing instructions).

7. Maintenance

Regular maintenance ensures the longevity and safe operation of your FDIK parking heater.

7.1 Cleaning

  • Exterior: Wipe the exterior of the heater with a damp cloth. Do not use abrasive cleaners or solvents.
  • Air Inlet/Outlet: Ensure the air inlet and outlet grilles are free from dust, debris, or obstructions. Use a soft brush or vacuum cleaner to clean them.
  • Air Filter: Periodically check and clean or replace the air filter to maintain optimal airflow and prevent dust from entering the combustion chamber.

7.2 Fuel System Checks

  • Fuel Filter: Inspect the fuel filter regularly for contamination. Replace it if it appears dirty or clogged.
  • Fuel Lines: Check all fuel lines for leaks, cracks, or damage. Ensure connections are secure.
  • Fuel Tank: Keep the fuel tank clean and free of water or sediment. Use only clean diesel fuel.

7.3 Exhaust System Checks

  • Inspect the exhaust pipe for any blockages, cracks, or loose connections. Ensure exhaust gases are safely directed away from the vehicle and occupants.

7.4 Electrical System Checks

  • Check all electrical connections for tightness and corrosion.
  • Inspect the wire harness for any signs of wear or damage.
  • Ensure the fuse is of the correct rating (e.g., for a 12V 2KW unit, a suitable fuse should be used to protect the circuit from overcurrent).

8. Troubleshooting

This section addresses common issues you might encounter with your FDIK parking heater.

ProblemPossible CauseSolution
Heater does not turn onNo power, loose wiring, blown fuse, faulty controller.Check battery connections, inspect wire harness, replace fuse if blown, ensure controller is properly connected.
Heater turns on but does not igniteNo fuel, clogged fuel filter, air in fuel line, faulty glow plug, incorrect fuel pump angle.Check fuel level, prime fuel line, replace fuel filter, check glow plug, ensure oil pump is installed at 15°-35° angle.
Remote control not workingNot paired, dead battery, out of range.To pair remote: With the heater off, press and hold the 'OK' button on the main controller. While holding, press the 'ON' button on the remote control. The display should show a pairing confirmation. Release the 'OK' button. Replace remote battery. Ensure remote is within effective range (up to 100m in direct line of sight).
Heater produces smoke or unusual smellIncomplete combustion, exhaust leak, foreign object in air ducts.Turn off immediately. Check exhaust system for leaks. Inspect air ducts for obstructions. Ensure proper fuel-air mixture (may require professional calibration).
Heater is noisyLoose components, fan obstruction, worn motor bearings.Check for loose mounting. Inspect fan for obstructions. If noise persists, professional service may be required.
Display shows error codeInternal fault.Refer to the specific error code in the full user manual (if available) or contact support.
Control unit language is ChineseDefault language setting.Some units may not have an English language option. If available, the setting is usually found in the advanced menu by pressing and holding a combination of buttons (e.g., 'Set' and 'Up' for several seconds). Consult the seller for specific instructions for your unit.

9. User Tips

  • Fuel Type: This heater is designed for diesel fuel only. Do NOT use gasoline or other fuels, as this can cause severe damage and safety hazards.
  • Remote Range: The remote control typically works up to 100 meters in a direct line of sight. Obstacles like walls can significantly reduce this range.
  • Temperature Control: The heater has two modes: a fixed power output (5 levels) or a temperature-controlled mode (16-35°C). Use the temperature control mode for consistent comfort.
  • Fuse Size: For a 12V 2KW unit, ensure you use an appropriately sized fuse to protect the electrical circuit. Consult an automotive electrician if unsure.
  • Fuel Calibration: Some advanced units may offer fuel supply calibration to optimize combustion. Refer to your specific manual or contact the seller for details on this feature.

10. Warranty and Support

FDIK offers a warranty for its products. Please refer to the specific warranty terms provided at the time of purchase. Generally, the product comes with a one-year free warranty for quality problems not caused by human factors. If parts are damaged within this period, the seller may provide free replacements.

Information on Brand Story, After-sales Service, and Purchase Information including Warranty
Figure 10.1: After-sales service and warranty information.

Customer Support:

For technical assistance, troubleshooting, or warranty claims, please contact the FDIK Official Store or your point of purchase. When contacting support, please have your product model and purchase details ready.

The FDIK brand is committed to providing quality products and support. They have been established since 2010 and have partners worldwide.

© 2023 FDIK. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.