Jessinie STM32F103C8T6 USB Interface 10 Channel 12Bit AD Sampling ADC Data Acquisition STM32 UART Communication ADC Module Board

Contents

12Bit USB Interface 10 Channel AD Sampling ADC Data Acquisition STM32 UART Communication Module Board User Manual

Model: STM32F103C8T6 USB Interface 10 Channel 12Bit AD Sampling ADC Data Acquisition STM32 UART Communication ADC Module

Brand: Jessinie

1. Introduction

1.1 Product Overview

The Jessinie STM32F103C8T6 USB Interface 10 Channel 12Bit AD Sampling ADC Data Acquisition STM32 UART Communication Module Board is designed for precise analog-to-digital conversion and data acquisition. It leverages the internal 10-channel ADC resources of the STM32F103 series microcontroller as its sampling core. The acquired data is transferred to internal memory via the STM32, which helps reduce CPU load and enhance the stability and accuracy of AD sampling. An onboard USB to serial port chip facilitates data transfer to a host computer, making it easy to view AD sampling results.

1.2 Key Features

  • Onboard STM32 master chip for efficient processing.
  • Integrated CH340 serial port to USB chip for convenient PC connectivity and data viewing.
  • Reserved UART serial communication interface for connection to external MCUs.
  • 10-channel single-ended analog input.
  • Sampling voltage input range: 0~3.3V.
  • Power supply voltage: 5V/3.3V.
  • Resolution: 12Bit (4096).
  • Board size: 50*33mm.
Top view of the ADC module board with USB connector and terminal blocks

Figure 1: Top view of the Jessinie ADC Module Board.

Top and bottom view comparison of the ADC module board

Figure 2: Top and bottom view of the ADC Module Board.

2. Safety & Warnings

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • WARNING: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • The sampling voltage input should not exceed 3.3V, otherwise there is a possibility of damage to the chip.

⚠ California Proposition 65 Warning:

This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Setup

3.1 Pre-Installation Considerations

Prior to integration, ensure that the operational environment aligns with specified technical parameters. It is recommended to verify compatibility with existing systems to facilitate seamless implementation.

3.2 Driver Installation

Before connecting the module to your computer, install the necessary driver for the CH340 USB to serial port chip. This driver enables your computer to recognize and communicate with the module.

3.3 Physical Connection

Connect the module to your computer via the USB port. The module features terminal blocks for connecting analog input signals and power. Refer to the labeled diagram below for pin assignments:

Labeled diagram of the ADC module showing pinouts for GND, 3V3, 5V, TX, RX, and AD sampling inputs IN0-IN9

Figure 3: ADC Module Pinout Diagram.

  • GND: Power supply negative / sampling voltage common ground interface.
  • 3V3: 3.3V power input/output.
  • 5V: 5V power input/output.
  • TX: UART Transmit pin.
  • RX: UART Receive pin.
  • IN0-IN9: AD sampling voltage input channels.

Connect the positive terminal of your sampling voltage to one of the IN0-IN9 inputs. Connect the negative terminal of your sampling voltage to a GND pin. Ensure that the sampling voltage does not exceed 3.3V.

3.4 Circuit Schematics

For advanced users and developers, the following schematics provide detailed information on the module's internal circuitry:

Schematic diagram for the CH340 USB-to-Serial converter chip

Figure 4: CH340 USB-to-Serial Converter Schematic. This diagram shows the connections for the CH340 chip, including USB data lines (D+, D-), power (5V), and UART communication lines (TX, RX).

Schematic diagram for the STM32F103 microcontroller, showing pin assignments for ADC inputs, power, and communication

Figure 5: STM32F103 Microcontroller Schematic. This diagram details the STM32F103 connections, including ADC input pins (IN0-IN9), power supply (3V3, 5V), and UART pins (PA9, PA10).

Schematic diagram for the power supply circuit, featuring the AMS1117 voltage regulator

Figure 6: Power Supply Circuit Schematic. This diagram illustrates the 5V to 3.3V conversion using the AMS1117 voltage regulator and associated filtering capacitors.

4. Operating Instructions

4.1 AD Sampling via PC (USB)

  1. Install the CH340 USB to serial port chip driver on your computer.
  2. Plug the module into a USB port on your computer.
  3. Connect your sampling voltage source: IN0-IN9 to the positive terminal and GND to the negative terminal (common ground).
  4. Open a serial debugging assistant software on your PC.
  5. Select the correct COM port corresponding to the module and set the baud rate to 115200.
  6. You can now view the AD sampling results, which are refreshed approximately every 500ms. This refresh rate can be modified in the source code if needed.

4.2 Communication with External MCU (UART)

If you intend to use an external Microcontroller Unit (MCU) to acquire sampling data directly, connect the MCU's 3.3V, RX, TX, and GND pins to the module's 3.3V, TX, RX, and GND pins respectively. The module can also be powered by 5V if required. The data transfer protocol can be found by examining the module's source code.

4.3 Programming and Firmware Update

To modify the source code and re-program the module:

  1. Insert the module into a computer's USB port.
  2. Place the jumper cap on the module to the 3V3 end. (Important: After programming is complete, move the jumper cap back to GND).
  3. Open the programming software (e.g., FlyMcu).
  4. Load the desired hex file into the software.
  5. Set the correct port number and baud rate (e.g., 115200) and other relevant parameters.
  6. Click "Start Programming".
  7. Use tweezers to momentarily short the two ends of capacitor C9 (this acts as a reset). The programming process should then begin.

Note: The module is shipped without pre-downloaded firmware. You need to download it directly using STLink or the method described above.

Video 1: Product demonstration and basic operation overview.

5. Maintenance & Care

  • Implement routine maintenance protocols to uphold product standards.
  • Periodic inspections are encouraged to ensure ongoing compliance with quality expectations.
  • Store the module in a dry place.
  • Keep away from children.

6. Troubleshooting

  • Random AD Values: If a certain channel (IN0-IN9) has no sampling voltage input, the output for that channel will be a random value. This is normal behavior.
  • Module Damage: Ensure the sampling voltage input does not exceed 3.3V. Applying higher voltages can permanently damage the chip.
  • No Data on PC: Verify that the CH340 driver is correctly installed, the module is properly connected via USB, and the correct COM port and baud rate (115200) are selected in your serial debugging assistant.
  • Programming Issues: Ensure the jumper cap is correctly set to 3V3 during programming and returned to GND afterward. Confirm the hex file is valid and the reset procedure (shorting C9) is performed correctly.

7. Specifications

AttributeValue
Brand NameJessinie
ModelSTM32F103C8T6 USB Interface 10 Channel 12Bit AD Sampling Data Acquisition STM32 UART Communication ADC Module
TypeVoltage Regulator / ADC Module
OriginMainland China
ConditionNew
ApplicationOther (AD Sampling, Data Acquisition)
Sampling Voltage Input Range0~3.3V
Supply Voltage5V/3.3V
Resolution12Bit (4096)
Dissipation Power10 Channel 12Bit
Operating TemperatureADC Module (General operating temperature for integrated circuits)
PackageTQFP
is_customizedYes
High-concerned chemicalnone
Board Size50*33mm

8. User Tips

  • The default AD sampling refresh rate is 500ms. This can be adjusted by modifying the source code to suit specific application requirements.
  • Unused input channels (IN0-IN9) can be reconfigured and used as general-purpose I/O (GPIO) ports if desired, by modifying the module's source code.
  • This module is primarily used for AD Sampling and Data Acquisition tasks.

9. Compliance Information

9.1 CE Marking

This product conforms to the following EU Directives:

  • 2014/35/EU (Low Voltage Directive)
  • 2014/30/EU (Electromagnetic Compatibility Directive)

CE

9.2 RoHS Declaration

This product is in compliance with Directive 2011/65/EU and its amendment (EU) 2015/863, concerning the restriction of hazardous substances (Pb, Cd, Hg, etc.) in electrical and electronic equipment.

10. Manufacturer & EU Representative Information

10.1 Manufacturer

  • Company Name: Shenzhen ZhengYi Electronic Technology Co., Ltd
  • Full Address: Jia An Road XA 41 D3-6F, Bao An District, ShenZhen, Guangdong Province, China
  • Email: 1020636662@qq.com

10.2 EU Authorized Representative

  • Company Name: eVatmaster Consulting GmbH
  • Full Address: Raiffeisen Street2 B11, 63110 Rodgau, Hessen, Germany
  • Email: contact@evatmaster.com

11. Further Information

For further details, consult the official documentation or contact our support team. A comprehensive user manual in PDF format is available for download:

Download User Manual (PDF)

Disclaimer: The manufacturer assumes no liability for outcomes resulting from non-compliance with these instructions, improper use, or unauthorized modifications. Specifications are subject to change without prior notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.