eletechsup WHTCA01_kit

Contents

Instruction Manual

eletechsup WHTCA01_kit DC 3.7-5V Multifunction Atomizer/Humidifier Controller

Model: WHTCA01_kit | Brand: eletechsup

1. Introduction

The eletechsup WHTCA01_kit is a compact and versatile controller designed for driving 108KHz atomizing sheets, suitable for various humidifier and atomizer applications. It supports both Type-C USB and direct DC 3.7-5V power input and offers multiple customizable operating modes, including continuous, intermittent, and timed operation. This manual will guide you through the installation, operation, and maintenance of your controller kit.

2. Package Contents

Please verify that all items listed below are included in your package:

  • 1x TYPE-C Atomizer / Humidifier Controller (WHTCA01_kit)
  • 1x Atomizing Sheet (108KHz)
  • 1x Humidifier Cotton Rod
Image showing the controller board, atomizing sheet, and cotton rod included in the kit.
Figure 2.1: Components included in the WHTCA01_kit.

3. Specifications

FeatureSpecification
Model NumberWHTCA01_kit
Brand Nameeletechsup
Working VoltageDC 3.7-5.5V (Recommended 5V)
Operating VoltageDC 3.7-5V
Work Current330mA
Standby Current20uA
Power Supply InterfaceType-C USB
Humidifier InterfacePH2.0 Terminal
Frequency108kHz
Dimensions (Controller)40 x 16.5 x 9 mm
Weight (Controller)4.5 grams
Atomizing Sheet Working VoltageDC 3.7-5.5V
Atomizing Sheet Working Current300mA
Atomizing Sheet Number of Holes740
Atomizing Sheet Hole Diameter5µm
Atomizing Sheet Power2W
Atomizing Sheet Frequency108KHz
Atomizing Sheet Terminal Spec.PH2.0
Atomizing Sheet Line Length100mm
Atomizing Sheet Steel Sheet Diameter16mm
Atomizing Sheet Silicone Ring Diameter20mm
Humidifier Cotton Rod Diameter8mm
Humidifier Cotton Rod Length100mm
Humidifier Cotton Rod MaterialNon-adhesive acetic acid fiber

4. Setup Instructions

Follow these steps to set up your atomizer/humidifier controller kit:

  1. Connect Atomizing Sheet: Connect the atomizing sheet to the PH2.0 terminal on the controller board. Ensure the connection is secure.
  2. Insert Humidifier Cotton Rod: Place the humidifier cotton rod into the central hole of the atomizing sheet assembly. Ensure it is fully inserted and makes good contact with the atomizing surface.
  3. Power Supply Connection: Choose one of the following methods to power the controller:
    • Type-C USB Power: Connect a Type-C USB cable from a 5V power source (e.g., USB charger, power bank) with at least 1A output to the Type-C port on the controller board.
      Wiring diagram showing Type-C USB power connection to the controller and atomizing sheet.
      Figure 4.1: Type-C USB Power Supply Connection.
    • Direct DC 3.7-5V Power: Solder DC 3.7-5V power wires directly to the VIN and GND pads on the controller board. Ensure correct polarity (+ to VIN, - to GND).
      Wiring diagram showing direct DC 3.7-5V power connection to the controller and atomizing sheet.
      Figure 4.2: Direct DC 3.7-5V Power Supply Connection.
  4. Water Placement: For humidification, place the atomizing sheet and cotton rod assembly into a container with water, ensuring the cotton rod is submerged and the atomizing sheet is just above the water surface or partially submerged as per your humidifier design.
Video 4.3: Product demonstration showing setup and mist generation.

5. Operating Instructions

The controller features a 'KEY' button for basic operation and weldable 'M0', 'M1', 'M2' pads for advanced mode selection.

5.1 Basic Operation (KEY Button)

  • Once powered, the work indicator (D1) will light up.
  • Press the 'KEY' button to start atomization.
  • Press the 'KEY' button again to stop atomization.

5.2 Advanced Mode Selection (M0, M1, M2 Pads)

The controller supports multiple function modes which are selected by soldering specific combinations of the M0, M1, and M2 pads. These pads are located on the board as shown in Figure 5.1. Ensure the device is powered off before making any soldering changes.

Diagram showing the M0, M1, M2 pads and the KEY button on the controller board.
Figure 5.1: Controller board layout with M0, M1, M2 pads and KEY button.
M0 M1 M2 ConfigurationOperating ModeDescription
Open (No Solder)Uninterrupted WorkDoes not work after power-on. Click the button to work, click again to stop working.
M0 SolderedWork every 3 secondsDoes not work after power-on. Click the button to work for 3 seconds, stop for 3 seconds, and repeat the cycle. Click the button again to stop working.
M1 SolderedWork every 10 secondsDoes not work after power-on. Click the button to work for 10 seconds, stop for 10 seconds, and repeat the cycle. Click the button again to stop working.
M0 & M1 Soldered1 minute timerDoes not work after power-on. Click the button to work for 1 minute and then stop. Click the button again during work to stop working. Click again to repeat the above action.
M2 Soldered5 minutes timerDoes not work after power-on. Click the button to work for 5 minutes and then stop. Click the button again during work to stop working. Click again to repeat the above action.
M0 & M2 Soldered30 minutes timerDoes not work after power-on. Click the button to work for 30 minutes and then stop. Click the button again during work to stop working. Click again to repeat the above action.
M1 & M2 Soldered60 minutes timerDoes not work after power-on. Click the button to work for 60 minutes and then stop. Click the button again during work to stop working. Click again to repeat the above action.
M0, M1 & M2 Soldered120 minutes timerDoes not work after power-on. Click the button to work for 120 minutes and then stop. Click the button again during work to stop working. Click again to repeat the above action.

6. Maintenance

  • Humidifier Cotton Rod: The cotton rod is consumable and should be replaced periodically, especially if you notice reduced mist output or a change in water absorption. Ensure the replacement rod has a diameter of 8mm and a length of 100mm.
    Image showing the humidifier cotton rod with its dimensions: Diameter 8mm, Length 100mm.
    Figure 6.1: Humidifier Cotton Rod Specifications.
  • Atomizing Sheet: If mist output decreases, gently clean the surface of the atomizing sheet with a soft cloth or cotton swab. Avoid using abrasive materials or harsh chemicals.
    Image showing the atomizing sheet with its specifications.
    Figure 6.2: Atomizing Sheet Specifications.
  • General Cleaning: Keep the controller board clean and dry. Avoid exposure to excessive moisture or dust.

7. Troubleshooting

  • No Mist Output:
    • Check if the power supply is connected correctly and providing the recommended voltage (DC 3.7-5.5V).
    • Ensure the atomizing sheet is properly connected to the PH2.0 interface.
    • Verify that the humidifier cotton rod is fully saturated with water and making good contact with the atomizing sheet.
    • Confirm there is sufficient water in the container.
    • Press the 'KEY' button to activate the atomization.
  • Intermittent or Weak Mist:
    • Check the selected operating mode (M0, M1, M2 configurations) to ensure it matches your desired behavior.
    • Clean the atomizing sheet surface for any mineral buildup or debris.
    • Replace the humidifier cotton rod if it appears worn or clogged.
    • Ensure the power supply can provide sufficient current (recommended 1A for 5V).
  • Controller Not Responding:
    • Disconnect and reconnect the power supply.
    • Check for any visible damage to the controller board or connections.

8. User Tips

  • Initial Setup: Always ensure the humidifier cotton rod is completely soaked in water before the first use to prevent dry burning of the atomizing sheet and ensure optimal mist production.
  • Power Source: For best performance and longevity, use a stable 5V power supply with at least 1A output. Lower current power sources might result in weaker mist or inconsistent operation.
  • Water Quality: Using distilled or purified water can help prevent mineral buildup on the atomizing sheet, extending its lifespan and maintaining consistent mist output.
  • Customization: Experiment with the different M0, M1, M2 soldering configurations to find the operating mode that best suits your application.

9. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For technical support, troubleshooting assistance, or warranty claims, please contact the seller directly through the platform where the product was purchased. Please provide your order number and a detailed description of the issue.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.