BAOFENG UV-5R

Contents

BaoFeng UV-5R Walkie Talkie User Manual

Professional FM Transceiver

1. Introduction

Thank you for purchasing the BaoFeng UV-5R Amateur Portable Radio. This dual-band/dual-display radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully before use to ensure maximum performance from your radio.

This manual covers the features, installation, operation, maintenance, troubleshooting, and specifications of the BaoFeng UV-5R walkie talkie.

BaoFeng UV-5R Walkie Talkie in various colors

Image: BaoFeng UV-5R Walkie Talkie in camouflage, yellow, black, blue, and red.

2. Safety Information

The following safety precautions must always be observed during the operation, service, and repair of this equipment:

  • This equipment should only be serviced by qualified technicians.
  • Do not modify the radio for any reason.
  • Use only supplied or approved batteries and chargers.
  • Do not use any portable radio with a damaged antenna. Contact with a damaged antenna can cause minor burns.
  • Turn off your radio before entering any area with explosive and flammable materials.
  • Do not charge your battery in a location with explosive and flammable materials.
  • To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
  • Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
  • Turn off your radio before entering a blasting area.
  • For vehicles with an airbag, do not place a radio in the area over an airbag or in the airbag deployment area.
  • Do not expose the radio to direct sunlight for a long time, nor place it close to a heating source.
  • When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips.
  • Keep the antenna at least 2.5 centimeters away from your body when transmitting.

WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.

3. Features and Functions

The BaoFeng UV-5R is a professional FM transceiver with a user-friendly design, offering a range of features for reliable communication:

  • Durable, wear-resistant construction with environmental protection PC material.
  • Sensitive and durable rubber keyboard.
  • Dual-band handheld transceiver with display function menu on the LCD.
  • Commercial FM radio receiver (65MHz-108MHz) - Note: Due to an IC production stop, newer models may not include the FM function.
  • Incorporates 105 "DCS" codes and 50 programmable "CTCSS" privacy codes.
  • VOX (Voice Operated Transmission) function.
  • Alarm function.
  • Up to 128 memory channels.
  • Broadband (Wide) / Narrowband (Narrow) selectable.
  • High power / low (5W/1W) selectable.
  • Display illumination and programmable keyboard with "beep" function.
  • Dual Watch/Dual Reception.
  • Selectable Frequency Step: 2.5/5/6.25/10/12.5/25 kHz.
  • "OFFSET" function (frequency offset for repeater access).
  • Battery saving function "SAVE".
  • Timer transmission "TOT" programmable.
  • Built-in RX CTCSS/DCS scan.
  • Built-in LED flashlight.
  • Programmable by PC.
  • Squelch level adjustable from 0 to 9.
  • Crossband reception/transmission.
  • Tone end of transmission.
  • Built-in key lock.

4. Unpacking and Checking Equipment

Carefully unpack the transceiver. We recommend identifying all items before discarding the packing material. If any items are missing or damaged, contact your dealer immediately.

Standard Accessories Included:

Standard accessories for BaoFeng UV-5R: radio main unit, antenna, belt clip, hand strap, earphone, battery, desk charger, charger adapter, user manual.

Image: Standard accessories including the radio, antenna, belt clip, hand strap, earphone, battery, desk charger, charger adapter, and user manual.

  • Portable UV-5R Radio (Main unit)
  • Battery (Li-ion, 1800mAh)
  • Antenna (High gain DualBand)
  • Desk Charger
  • Charger Adapter
  • Belt Clip
  • Hand Strap (Sling)
  • Earphone
  • User's Manual (PDF available for download: User Manual PDF)

Note: Items included in the package may differ depending on the country of purchase. Consult your dealer for more information.

5. Setup and Installation

5.1. Installing the Antenna

Install the antenna by turning it clockwise onto the radio's connector until it stops. Hold the antenna by its base, not the top, when installing.

Diagram showing how to screw the antenna onto the top of the walkie talkie.

Image: Antenna installation diagram.

  • If using an external antenna, ensure its SWR (Standing Wave Ratio) is about 1.5:1 or less to prevent damage to the transceiver's final transistors.
  • Do not hold the antenna with your hand or wrap the outside of it to avoid bad operation.
  • Never transmit without an antenna.

5.2. Installing the Belt Clip

If needed, install the belt clip at the rear of the battery compartment cover using the provided screws.

Diagram showing how to attach the belt clip to the back of the walkie talkie battery.

Image: Belt clip installation diagram.

Note: Do not use any glue to fix the screw on the belt clip, as solvents in glue may damage the battery casing.

5.3. Micro-Headset Installation

Plug the external micro-headset connector into the 'SP. & MIC' jack on the side of the transceiver.

Diagram showing where to plug in the micro-headset into the walkie talkie.

Image: Micro-headset connection diagram.

5.4. Battery Installation and Removal

Installation:

  1. Ensure the battery is aligned with the guide rails on the aluminum chassis.
  2. Slide the battery upwards until a 'click' is heard, indicating it's locked by the battery latch at the bottom.

Removal:

  1. Turn off the radio.
  2. Slide the battery latch (at the bottom of the radio) in the direction indicated by the arrow.
  3. Slide the battery down about 1 to 2 centimeters, then remove it from the radio.
Diagram showing how to install and remove the battery from the walkie talkie.

Image: Battery installation and removal diagram.

6. Battery Charging and Information

6.1. Charging Procedure

Use only the charger specified by the manufacturer. The charger's LED indicates the charging progress.

  1. Plug the power cord into the adapter.
  2. Plug the AC connector of the adapter into an AC outlet.
  3. Plug the DC connector of the adapter into the DC socket on the back of the charger.
  4. Place the radio with the battery attached, or the battery alone, in the charger.
  5. Ensure the battery is in good contact with the charging terminals. The charging process begins when the red LED lights.
  6. The green LED lights approximately 4 hours later, indicating the battery is fully charged. Remove the radio/battery from the charger.
Diagram showing the charging base and how to place the walkie talkie or battery for charging.

Image: Charging base and battery charging process.

6.2. LED Indication during Charging

Charging StatusLED Indication
Standby (no-load)Red LED flashes, Green LED glows
ChargingRed LED solidly glows
Fully ChargedGreen LED solidly glows
ErrorRed LED flashes, Green LED glows

6.3. Battery Information and Care

Initial Use: New batteries are shipped uncharged. Charge a new battery for 5 hours before initial use. Maximum capacity is achieved after three full charge/discharge cycles. Recharge when battery power is low.

WARNING:

  • To reduce the risk of injury, charge only the battery specified by the manufacturer. Other batteries may burst, causing bodily injury and property damage.
  • Do not dispose of batteries in a fire.
  • Dispose of batteries according to local regulations (e.g., recycling). Do not dispose as household waste.
  • Never attempt to disassemble the battery.

Battery Tips:

  • Charge batteries at temperatures between 5℃ and 40℃.
  • Turn off the radio when charging an attached battery to ensure a full charge.
  • Do not cut off power or remove the battery during charging.
  • Never charge a wet battery; dry it with a soft cloth first.
  • Replace the battery when operating time is noticeably shorter than normal.

Prolonging Battery Life:

  • Battery performance decreases significantly below 0°C. A spare battery is recommended in cold weather.
  • Clean battery contacts with a dry cloth before attaching the battery to the radio.

Battery Storage:

  • Fully charge batteries before long-term storage to prevent over-discharge damage.
  • Recharge Li-Ion batteries every 6 months during storage to prevent capacity reduction.
  • Store batteries in a cool, dry place at room temperature to reduce self-discharge.

7. Parts, Controls, and Keys

7.1. Radio Overview

Front and side view of the BaoFeng UV-5R walkie talkie with labels for antenna, flashlight, knob, call key, VFO/MR, PTT key, LED indicator, MONI key, A/B key, keypad, sling buckle, LCD screen, SP jack, Mic jack, Band key.

Image: Labeled diagram of the BaoFeng UV-5R radio's parts and controls.

No.PartNo.Part
1Antenna10Strap Buckle
2Flashlight11Accessory Jack
3Knob (ON/OFF, Volume)12A/B Key (frequency display switches)
4LCD13BAND Key (band switches)
5SK-Side Key1/CALL (radio, alarm)14Keypad
6SK-Side Key2/MONI (flashlight, monitor)15SP. & MIC.
7PTT Key (push-to-talk)16Battery Pack
8VFO/MR (frequency mode/channel mode)17Battery Contacts
9LED Indicator18Battery Remove Button

7.2. Command/Key Definition

  • [PTT] (Push-To-Talk): Press and hold to transmit; release to receive.
  • SK-SIDE KEY1/[CALL]:
    • Press to activate/deactivate FM Radio.
    • Press and hold to activate/deactivate the alarm function.
  • SK-SIDE KEY2/[MONI]:
    • Press to turn on/off the flashlight.
    • Press and hold to monitor the signal.
  • [VFO/MR] Button: Press to switch between frequency mode and channel mode.
  • [A/B] Button: Press to switch frequency display.
  • [BAND] Button:
    • Press to switch band display.
    • While FM radio is active, press to switch the FM radio band (65-75MHz/76-108MHz).
  • [*SCAN] Key:
    • Press to activate the Reverse function (exchanges reception and transmission frequency).
    • Press and hold for 2 seconds to start scanning (frequency/channel).
    • While FM radio is active, press to search FM radio stations.
    • While setting RX CTCSS/DCS, press to scan the RX CTCSS/DCS.
  • [#] Key:
    • Under channel mode, press to switch High/Low transmit power.
    • Press and hold for 2 seconds to lock/unlock the keypad.
  • [MENU] Key: To enter the menu and confirm settings.
  • [▲][▼] Keys: Press for fast frequency up/down. Press to change scanning direction.
  • [EXIT] Key: To cancel/clear or exit.
  • Numeric Keypad: Used to enter information for programming and to send signal codes in transmission mode (if set by PC software).
  • Accessory Jack: Used to connect audio accessories or programming cable.

8. LCD Display Icons

The display icons appear when certain operations or features are active:

IconDescription
100Operating channel.
75Operating frequency.
CT'CTCSS' activated.
DCS'DCS' activated.
+-Frequency offset direction for accessing repeaters.
SDual Watch/Dual Reception functions activated.
VOXFunction 'VOX' enabled.
RReverse function activated.
NWide Band selected.
...Battery Level indicator.
ỞKeypad lock function activated.
LLow transmit power.
▲▼Operation frequency.
Signal Strength Level.

9. Basic Operation

9.1. Radio ON-OFF / Volume Control

  1. Ensure the antenna and battery are correctly installed and the battery is charged.
  2. Rotate the knob clockwise to turn the radio ON.
  3. Continue rotating the knob clockwise to increase the volume, or counter-clockwise to decrease the volume.
  4. Rotate the knob fully counter-clockwise until a 'click' is heard to turn the radio OFF.

9.2. Selecting a Frequency or Channel

  • Press the [▲] or [▼] keys to select the desired frequency/channel. The display will show the selected frequency/channel.
  • Press and hold the [▲] or [▼] keys for fast frequency up or down.

Note: You cannot select a channel if it has not been previously stored.

9.3. 1750 Hz Tone for Repeater Access

To establish long-distance communications through an amateur radio repeater that requires a 1750 Hz tone for activation:

  • Press and hold the [PTT] button.
  • While holding [PTT], press the [BAND] button to transmit a 1750Hz tone.

10. Advanced Operation (Menu Settings)

You can program your transceiver's operating parameters through the setup menu to suit your needs and preferences.

10.1. Set Menu Description

MenuFunction/DescriptionAvailable Settings
0SQL (Squelch level)0-9
1STEP (Frequency step)2.5/5/6.25/10/12.5/25kHz
2TXP (Transmit power)HIGH/LOW
3SAVE (Battery save, 1:1/1:2/1:3/1:4)OFF/1/2/3/4
4VOX (Voice operated transmission)OFF/0-10
5W/N (Wideband/narrowband)WIDE/NARR
6ABR (Display illumination)OFF/1/2/3/4/5s
7TDR (Dual watch/dual reception)OFF/ON
8BEEP (Keypad beep)OFF/ON
9TOT (Transmission timer)15/30/45/60.../585/600seconds
10R-DCS (Reception digital coded squelch)OFF/D023N...D7541
11R-CTS (Reception Continuous Tone Coded Squelch)67.0Hz...254.1Hz
14VOICE (Voice prompt)OFF/ON
15ANI (Automatic number identification)(PC software only)
16DTMFST (DTMF tone of transmitting code)OFF/DT-ST/ANI-ST/DT+ANI
17S-CODE (Signal code)1,...,15 groups
18SC-REV (Scan resume method)TO/CO/SE
19PTT-ID (transmit signal code)OFF/BOT/EOT/BOTH
20PTT-LT (delay signal code sending)0,...,30ms
21MDF-A (channel mode A display)FREQ/CH/NAME
22MDF-B (channel mode B display)FREQ/CH/NAME
23BCL (Busy channel lockout)OFF/ON
24AUTOLK (keypad locked automatically)OFF/ON
25SFT-D (direction of frequency shift)OFF/+/-
26OFFSET (frequency shift)00.000...69.990
27MEMCH (stored in memory channels)000,...127
28DELCH (delete memory channels)000,...127
29WT-LED (standby illumination color)OFF/BLUE/ORANGE/PURPLE
30RX-LED (reception illumination color)OFF/BLUE/ORANGE/PURPLE
31TX-LED (transmission illumination color)OFF/BLUE/ORANGE/PURPLE
32AL-MOD (alarm mode)SITE/TONE/CODE
33BAND (band selection)VHF/UHF
34TX-AB (transmitting selection in dual watch)OFF/A/B
35STE (Tail Tone Elimination)OFF/ON
36RP_STE (Tail tone elimination in repeater communication)OFF/1,2,3...10
37RPT_RL (Delay the tail tone of repeater)OFF/1,2,3...10
38PONMGS (Boot display)FULL/MGS
39ROGER (tone end of transmission)ON/OFF
40RESET (Restore to default setting)VFO/ALL

10.2. Shortcut Menu Operation

  1. Press the [MENU] key, then use [▲] or [▼] to select the desired menu.
  2. Press the [MENU] key again to enter parameter setting.
  3. Use [▲] or [▼] to select the desired parameter.
  4. Press the [MENU] key to confirm and save. Press the [EXIT] key to cancel setting or clear input.

10.3. Specific Functions Explained

SQL (Squelch): Mutes the speaker in the absence of reception. Setting the squelch level correctly ensures you only hear sound when receiving signals, reducing battery consumption. Level 5 is recommended.

VOX (Voice Operated Transmission): Activates transmission automatically by detecting your voice, eliminating the need to press PTT. Adjust VOX Gain level for smooth transmission.

W/N (Wideband or Narrowband): Selects between wideband and narrowband transmission. Use narrowband in areas with saturated RF signals to avoid interference.

TDR (Dual Watch/Dual Reception): Allows operation between two frequencies (A and B). The transceiver periodically checks for signals on the scheduled frequency and stays on it if a signal is received.

TOT (Transmission Timer): Automatically controls transmission time to prevent overheating. The transceiver will stop transmitting automatically after the set time.

CTCSS/DCS: Used to establish communication in closed user groups. The squelch opens only when receiving a frequency with the same CTCSS/DCS codes programmed in your transceiver. If codes differ, the squelch will not open, but the signal may still be heard.

Note: The use of "CTCSS" or "DCS" does not guarantee complete confidentiality of communication.

ANI (Automatic Number Identification): Also known as PTT ID. An ID is transmitted when the PTT button is pressed and/or released, identifying the radio. This feature is typically set via PC software.

DTMFST (DTMF Tone of Transmitting Code): Configures how DTMF tones are transmitted. Options include OFF (tones not heard), DT-ST (tones heard), ANI-ST (tones heard with ANI), and DT-ANI (tones heard with DTMF and ANI). Set PTT-ID first.

SC-REV (Scan Resume Method): Determines how scanning resumes after detecting a communication:

  • TO (Time Operation): Scan stops for a predetermined time, then resumes.
  • CO (Carrier Operation): Scan stops and remains on the channel until the signal disappears.
  • SE (Search Operation): Scan stops and remains on the channel after detecting an active signal.

PTT-ID (PTT or Release PTT to Transmit Signal Code): Configures when the signal code is transmitted:

  • OFF: No code transmitted.
  • BOT: Code transmitted when PTT is pressed.
  • EOT: Code transmitted when PTT is released.
  • BOTH: Code transmitted when PTT is pressed and released.

BCL (Busy Channel Lockout): Prevents transmission if a strong signal is present on the channel, avoiding interference with ongoing communications.

SFT-D (Direction of Frequency Shift): Sets the direction of frequency displacement (offset) for repeater communication (OFF, +, or -).

OFFSET (Frequency Shift): Defines the difference between reception and transmission frequencies for repeater access. Set according to the repeater's requirements.

STE (Tail Tone Elimination): Activates or deactivates the transmission end tone. This function is primarily for direct transceiver-to-transceiver communication, not for repeaters.

10.4. CTCSS Table

NºTone (Hz)NºTone (Hz)NºTone (Hz)NºTone (Hz)NºTone (Hz)
167.01194.821131.831171.341203.5
269.31297.422136.532173.842206.5
371.913100.023141.333177.343210.7
474.414103.524146.234179.944218.1
577.015107.225151.435183.545225.7
679.716110.926156.736186.246229.1
782.517114.827159.837189.947233.6
885.418118.828162.238192.848241.8
988.519123.029165.539196.649250.3
1091.520127.330167.940199.550254.1

10.5. DCS Table

NºCodeNºCodeNºCodeNºCodeNºCode
1D023N22D131N43D251N64D371N85D532N
2D025N23D132N44D252N65D411N86D546N
3D026N24D134N45D255N66D412N87D565N
4D031N25D143N46D261N67D413N88D606N
5D032N26D145N47D263N68D423N89D612N
6D036N27D152N48D265N69D431N90D624N
7D043N28D155N49D266N70D432N91D627N
8D047N29D156N50D271N71D445N92D631N
9D051N30D162N51D274N72D446N93D632N
10D053N31D165N52D306N73D452N94D645N
11D054N32D172N53D311N74D454N95D654N
12D065N33D174N54D315N75D455N96D662N
13D071N34D205N55D325N76D462N97D664N
14D072N35D212N56D331N77D464N98D703N
15D073N36D223N57D332N78D465N99D712N
16D074N37D225N58D343N79D466N100D723N
17D114N38D226N59D346N80D503N101D731N
18D115N39D243N60D351N81D506N102D732N
19D116N40D244N61D356N82D516N103D734N
20D122N41D245N62D364N83D523N104D743N
21D125N42D246N63D365N84D526N105D754N

11. Technical Specifications

Table of technical specifications for the BaoFeng UV-5R walkie talkie, including general, transmitter, and receiver details.

Image: Detailed technical specifications table.

11.1. General Specifications

Frequency Range65MHz-108MHz (Commercial FM radio reception), VHF: 136MHz-174MHz (Rx/Tx), UHF: 400MHz-480MHz (Rx/Tx)
Memory ChannelsUp to 128 channels
Frequency Stability±2.5ppm
Frequency Step2.5/5/6.25/10/12.5/25kHz
Antenna Impedance50 Ω
Operating Temperature-20 ℃ to +60 ℃
Supply VoltageRechargeable Lithium-Ion 7.4V/1800mAh
Consumption in Standby<75mA
Consumption in Reception380mA
Consumption in Transmission≤1.4 A
Mode of OperationSimplex or semi-duplex
Duty Cycle03/03/54 min. (Rx / Tx / Standby)
Dimensions58mm x 110mm x 32mm
Weight130 g (approximate)

11.2. Transmitter Specifications

RF Power5W/1W
Type of ModulationFM
Emission Class16KΦF3E/11KΦF3E (W/N)
Maximum Deviation≤ ± 5 kHz / ≤ ± 2.5 kHz (W/N)
Spurious Emissions<-60 dB

11.3. Receiver Specifications

Receiver Sensitivity0.2 μV (at 12 dB SINAD)
Intermodulation60 dB
Audio Output1000mW
Adjacent Channel Selectivity65/60dB

Note: All specifications are subject to change without notice.

12. Troubleshooting

ProblemPossible Cause / Solution
The radio does not start.
  • The battery is low. Replace with a charged battery or proceed to charge the battery.
  • The battery is not installed correctly. Remove and reattach it.
The battery runs down quickly.
  • The battery life has ended. Replace with a new one.
  • The battery is not fully charged. Ensure it is charged completely.
The receiving indicator LED lights but no sound from the speaker.
  • The volume setting is too low. Adjust the volume.
  • The CTCSS or DCS undertones are not the same as those programmed in the other transceivers in your group. Adjust settings to match.
When transmitting, other group members do not receive the communication.
  • The CTCSS or DCS undertones are not the same as those programmed in the other transceivers in your group. Adjust settings to match.
  • You or your partner are too far apart or in an area with poor RF signal propagation.
In "standby" mode, the transceiver transmits without pressing the PTT.The VOX level adjustment function is set too sensitively. Adjust the VOX level.
Receives communications from other user groups while communicating with your group.
  • Change frequency or channel.
  • Change the CTCSS or DCS undertones in your group.
Communication with other members of your group is poor or low quality.You or your partner are too far away or in an area of poor radio signal propagation (e.g., inside a tunnel, underground car park, mountainous area, large metal structures).

If problems persist after these checks, contact your distributor, dealer, or service center.

13. User Tips

  • Check Battery Regularly: Ensure your battery is fully charged before use to avoid unexpected power loss. Some users have noted that the battery life is good, but it's always wise to keep it topped up.
  • Verify Settings: If you experience issues with communication (e.g., not hearing others or not being heard), double-check your volume, CTCSS/DCS codes, and frequency settings. Mismatched codes are a common cause of communication failure.
  • Antenna Care: Always ensure the antenna is securely attached before operating the radio. Avoid transmitting without an antenna to prevent damage.
  • Range Considerations: Be aware that environmental factors like terrain, buildings, and distance significantly impact radio range and signal quality. Communication may be poor in challenging environments.
  • Manual Reference: Keep this user manual handy for quick reference, especially for menu settings and troubleshooting common issues.

14. Warranty and Support

The device described in this Certificate is guaranteed for a period of one year from the date of sale to the final user. This Warranty Certificate is unique and not transferable and may not be reissued for new or original or copy. Substitution of product failure or any part thereof shall not involve extension of the guarantee.

The warranty covers the replacement and free replacement of all parts that are defective in materials and components used in manufacturing and/or assembly of the apparatus.

The warranty does not cover any faults caused by accident, improper installation and use, electric shock (e.g., storms), connection to a power source other than that specified, reverse polarity in the diet, or claims due to deterioration in the external appearance of normal use, nor the amount or condition of the accessories.

Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.

The warranty does not cover rechargeable batteries even if they are part of the equipment purchased as they are considered consumables. Impairment must be reported within a period of fifteen days from the date of purchase.

The warranty is void under the following assumptions:

  1. Devices that have been manipulated by unauthorized service providers.
  2. Equipment and accessories in which the serial number has been altered, deleted, or filed unreadable.
  3. Use of the product other than as intended.

To make use of the guarantee, it is necessary to provide the dealer or any of the Authorized Service with the defective device, its accessories, and the following documentation:

  1. Warranty Certificate duly completed and sealed.
  2. Original invoice which clearly identifies the device and the date of purchase.
  3. Description of the faults.

The warranty terms contained in this Certificate of Guarantee do not exclude, modify, or restrict the statutory rights of the buyer by virtue of the laws in force at the time of purchase, but are added to them.

Support: For further assistance or service, please contact your local dealer or the service center.

15. Product Video

Video: An overview of the BaoFeng manufacturing process and product display.

© 2024 BaoFeng. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.