MESTEK WM700A/WM700B

Contents

Mestek Inductive Wood Moisture Meter

Models: WM700A / WM700B

User Manual

1. Introduction

1.1. Overview

The Mestek Non-destructive Moisture Meter is designed to measure moisture content through a non-destructive humidity sensor. It is suitable for measuring moisture in various building materials such as concrete, wood, flooring, and walls. The maximum penetration depth is approximately 20-40mm.

Moisture can be a significant issue in construction and homes. Water from concrete, mortar, and plaster can take months to dissipate. Even with good insulation, water and moisture can penetrate brick walls. Trapped water, for instance, after floods, is released slowly. Excess moisture can lead to corrosion, mildew, decay, and paint peeling.

Mestek Inductive Wood & Wall Detector showing applications for Drywall, Masonry, and Wood

Figure 1: Inductive Wood & Wall Detector for Drywall, Masonry, and Wood.

1.2. Safety Information

  • This product is not a toy. Keep it out of reach of children to prevent danger or injury.
  • Keep the product away from high temperatures, direct sunlight, strong vibration, humidity, and corrosive gases or objects.
  • If the product is visibly damaged or operating abnormally, discontinue use immediately to avoid inaccurate measurements and potential accidents.
  • Ensure correct battery polarity during installation. Remove batteries for long-term storage to prevent leakage.
  • Do not disassemble the product to avoid malfunction.
  • The user is responsible for the measurement results obtained with this product. The manufacturer does not accept responsibility for damage caused by the application of these measurement results.

1.3. Important Warnings for Accurate Measurement

  • The humidity level displayed reflects the humidity on the outer surface and the average value determined inside the material. If visible surface moisture or water is present, wipe it off and allow the surface to dry for a few minutes before measuring.
  • The measuring depth of the device is 20-40mm. If the material thickness is less than 20mm, the measured humidity value may be inaccurate due to adjacent materials.
  • Other factors can affect measurement accuracy. Before measurement, ensure any paint residue, dust, or other debris on the surface is removed.
  • If the spherical sensor head is placed at a corner (e.g., tile joint or room corner), the measured value may be higher. The measuring head does not measure a single surface; it must be 80-100mm away from corners.
  • Keep hands away from the measuring head during measurement, as hand humidity can affect results.
  • If the measured material contains metal (e.g., nails, screws, wires, metal pipes) within the sensor's measuring area, the value may suddenly increase due to strong reflection.
  • Place the humidity sensor on smooth surfaces. Rough surfaces can lead to inaccurate measurement results.
  • The density of the measured material significantly influences results; values increase with material density.
  • The humidity sensor must be held at right angles directly to the surface being measured.
  • If the operating environment changes suddenly, measurement results may be inaccurate. Allow the product to acclimatize to the new environment for a period before use.
  • Do not drop or hit the product.

2. Product Features and Components

2.1. Key Features

  • Non-destructive measurement with spherical probe.
  • Measuring depth: WM700B (20-40mm), WM700A (0-20mm).
  • Large HD color display for easy reading.
  • Self-calibration function.
  • Moisture alarm function with adjustable critical values (0-100).
  • Records MAX and MIN values during testing.
  • Automatic shut-down after 30 minutes (can be disabled).
  • Low power indicator.
  • Data hold function.
Non-Destructive Spherical Hygrometer features including self-calibration, HD LCD screen, data hold, Max/MIN record, auto-shutdown, alarm function, low power indicator, and value display.

Figure 2: Key Features of the Mestek Moisture Meter.

Comparison of measured depth for WM700B (20-40mm) and WM700A (0-20mm)

Figure 3: Measured Depth Comparison between WM700B and WM700A.

Comparison between a non-destructive spherical hygrometer and a plug-in needle hygrometer, highlighting advantages of the spherical type.

Figure 4: Non-destructive vs. Pin-type Hygrometer.

2.2. LCD Display and Controls

The device features a color screen with various indicators and controls:

  • Analog Display: A color bar indicating moisture level (green for DRY, yellow for RISK, red for WET).
  • Numeric Display: Shows the measured moisture value.
  • Low Battery Indicator: Alerts when batteries need replacement.
  • DRY / RISK / WET Indicators: Textual indicators for moisture status.
  • HOLD: Indicates data hold function is active.
  • MAX / MIN: Displays maximum and minimum recorded values.
  • Automatic Shutdown Symbol: Indicates auto-off is enabled.
  • Non-destructive Humidity Sensor: The spherical probe for measurement.
  • Power Button (①): Short press to turn on/off.
  • SET Button: Used for alarm value settings.
  • Numeric Adjustment Keys (− / +): Used to adjust numerical values.
  • MEAS Button: Used for calibration and data hold.
Diagram of WM700B showing non-destructive moisture sensor, color screen, power button, alarm value set, calibration keys, data management, alarm numerical adaptation, and other controls.

Figure 5: WM700B Product Diagram with Labeled Controls.

Diagram of WM700A showing temperature and humidity sensing area, data hold, measurement mode selection, Celsius Fahrenheit switch, power, moisture sensor, and battery cover.

Figure 6: WM700A Product Diagram with Labeled Controls.

3. Setup

3.1. Battery Installation

The device requires 3 AAA 1.5V batteries (not included).

  1. Turn off the product power.
  2. Use a screwdriver to remove the screws of the battery cover on the back of the product.
  3. Remove the battery cover.
  4. Remove any old batteries if present.
  5. Replace with new 1.5V x 3 AAA batteries, ensuring correct polarity.
  6. Install the battery cover and tighten the fixing screws.

3.2. Initial Calibration

Calibration is crucial for accurate readings and should be performed after each power-on or change in measurement conditions.

  1. After turning on the unit for the first time, hold it in the air for calibration. Ensure the non-destructive humidity sensor (spherical probe) does not touch any objects.
  2. Maintain a minimum distance of 80-100mm from any surface or your hand to the spherical sensor head.
  3. Press the MEAS button to start the calibration procedure.
  4. During calibration, the LCD screen will display "CAL".
  5. Calibration is complete after the product emits two beeps in approximately 3 seconds.
  6. After calibration, the LCD should show the current humidity level, and the calibration value should be "0". If it is not "0", shut down and restart the unit, then repeat the calibration procedure.

Note:

  • If the product has not been calibrated, do not change the position of your hand in subsequent measurements. The measurement calibration and measurement must use the same hand position, as changes in hand position relative to the sensor can lead to measurement errors.
  • Calibration must always be carried out again after each switch-on, as well as each change of the measuring point or the measured object!

4. Operation

4.1. Power On/Off

  • Short press the power button (①) to switch the unit on or off.

4.2. Taking Measurements

  1. Hold the spherical sensor head at right angles to the surface you wish to measure.
  2. The display will show the measured moisture value.
  3. To measure a larger surface, move the product across it. The LCD screen will continuously display the current measured value, along with the maximum (MAX) and minimum (MIN) values recorded during the session.
  4. To lock the current value on the display, press the MEAS button. The "HOLD" symbol will appear on the display.
  5. To exit "HOLD" mode and resume continuous measurement, press the MEAS button again.
Mestek moisture meter showing a measurement on a wooden surface with DRY, RISK, WET indicators

Figure 7: Taking a measurement with the moisture meter.

Collage of usage scenarios including softwood, hardwood, wet wall, ceiling, concrete, and caravans

Figure 8: Various application scenarios for the moisture meter.

4.3. Setting Moisture Limit Values (Alarm Function)

The device provides three non-digital measurement formats: "DRY", "RISK", and "WET". When the humidity reaches "RISK" or "WET" levels, the unit will beep during measurement. In the "WET" range, the beeping will be more urgent.

By default, a humidity reading of <30 will display "DRY"; 30-60 will display "RISK"; and a reading above 60 will display "WET". You can adjust these limit values:

  1. While the "HOLD" symbol is displayed (after pressing MEAS once), press the SET button to enter the set mode.
  2. When the "RISK" symbol flashes, use the − or + keys to adjust the lower limit for "RISK". The value can be set from 0 to 50. The factory default setting is 30.
  3. Press the SET button to confirm your selection.
  4. When the "WET" symbol flashes, use the − or + keys to adjust the lower limit for "WET". The value can be set from 51 to 100. The factory default setting is 60.
  5. Press the SET button to confirm your selection. The LCD display will switch back to the initial mode ("HOLD"). The limit values for "RISK" and "WET" are now set and stored.
  6. Press the MEAS key to enter the measurement mode.

4.4. Automatic Shut-down

  • After measurement, you can short press the power button (①) to turn off the product.
  • If not manually turned off, the device will automatically shut down after 30 minutes of inactivity to conserve battery.
  • To cancel the automatic shutdown function: In the shutdown state, press the MEAS key to turn on the unit. The screen will show "APO" to indicate that the automatic shutdown function is canceled. Note that this setting is not saved and needs to be reset after each manual shutdown.
Mestek moisture meter with a clock indicating 30 minutes auto-off feature

Figure 9: Automatic Shut-down Feature.

5. Specifications

5.1. Technical Specifications

ParameterValue
Product NameNon-destructive moisture meter
Measurement Range0-100
Measured Depth (WM700B)20-40mm
Measured Depth (WM700A)0-20mm
Range of RISK Limit Value0-50 (Default 30)
Range of WET Limit Value51-100 (Default 60)
Automatic Shut-down30 minutes
Display TypeColor screen, DIGITAL, With Backlight
Battery1.5V AAA*3 (not included)
Operation CurrentAbout 30mA
Operation Temperature0-40 ℃
Operation Humidity0%-70% RH
Storage Environment-10~50℃ (5%-95% RH)
Dimension195*73*33mm
Weight190g (excluding batteries)
CertificationCE, FCC, RoHS
DIY SuppliesWoodworking

5.2. Humidity Comparison Table for Building Materials

Different materials have varying moisture tolerance levels. Refer to this table for general guidance:

Building MaterialHumidity Range (Unit)Humidity Status
Wood<50DRY
50-80RISK
>80WET
Cement<25DRY
25-50RISK
>50WET
Plaster<30DRY
30-60RISK
>60WET

6. Maintenance

6.1. Replacing Batteries

Refer to section 3.1. Battery Installation for detailed instructions on replacing the 1.5V AAA batteries.

6.2. Cleaning

If the surface of the product becomes stained or dusty, clean it with a wet sponge or a soft cloth. Do not use abrasive cleaners or solvents.

7. Troubleshooting

If you encounter inaccurate readings or unexpected behavior, consider the following:

  • Inaccurate Readings:
    • Surface Moisture: Ensure the surface is dry and free of visible water.
    • Material Thickness: If the material is less than 20mm thick, readings might be affected by underlying materials.
    • Surface Condition: Remove any paint residue, dust, or debris from the measurement surface.
    • Corner Measurement: Avoid measuring directly in corners; keep the sensor 80-100mm away.
    • Hand Position: Ensure your hand position is consistent with calibration and away from the sensor.
    • Metal Interference: Check for metal objects (nails, wires, pipes) within the sensor's measurement depth.
    • Rough Surfaces: Ensure the sensor is placed on a smooth surface.
    • Material Density: Be aware that denser materials may show higher readings.
    • Sensor Angle: Hold the sensor at a right angle to the surface.
    • Environmental Changes: Allow the device to acclimatize to the ambient temperature and humidity if moved to a new environment.
  • Calibration Issues: If calibration does not result in "0", repeat the calibration process after restarting the device.
  • Device Not Powering On: Check battery installation and ensure batteries are new and correctly oriented.

8. User Tips

  • Reference Dry Readings: When working on a project, take a dry reference measurement of the material to establish a baseline.
  • Screen Clarity: The color screen makes readings clear and easy to interpret, even with temperature and humidity displayed.
  • Versatile Use: This meter is highly effective for construction and household maintenance, especially for detecting dampness in walls, wood, and other building materials.
  • Non-Destructive Advantage: Appreciate the pinless design for checking moisture without damaging surfaces.

9. Frequently Asked Questions (FAQ)

Q: Does it measure moisture in fabric?
A: The primary application of this non-destructive moisture meter is for building materials like wood, masonry, drywall, and concrete. It is not designed for measuring moisture in fabrics.
Q: Does it work on ceramics and porcelain?
A: While it can detect moisture behind ceramic tiles or porcelain if the moisture has penetrated the substrate (e.g., drywall or concrete), it is not designed to measure the moisture content of the ceramic or porcelain material itself. The measurement depth is 20-40mm (WM700B) or 0-20mm (WM700A), so it measures the material beneath the tile.
Q: Does it come with a calibration certificate?
A: The product features a self-calibration function that should be performed before each use or when environmental conditions change. A separate calibration certificate is typically not included for this type of consumer-grade device.
Q: Is there a manual in Spanish?
A: This manual is provided in English. Please check the official Mestek website or contact customer support for manuals in other languages if available.
Q: Is it suitable for concrete and walls?
A: Yes, this non-destructive moisture meter is specifically designed for measuring moisture in concrete, masonry, drywall, and other wall materials, as well as wood.

10. Warranty and Support

For detailed warranty information, technical support, or further documentation, please refer to the official user manual PDF or contact Mestek customer service.

A comprehensive user manual in PDF format is available for download: Mestek Moisture Meter User Manual (PDF).

11. Product Video Demonstration

Video: Demonstration of the Mestek Pinless Moisture Meter in use, including detection of moisture in walls.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.