1. Product Overview
This manual provides instructions for the Weelye RX19 12V Control Box and its compatible 2.4G Bluetooth Remote Control, designed for children's electric ride-on toys. The control box features a slow start function, eliminating the need for additional slow starter installations.
Important Compatibility Note:
Ensure the purchased part has the same appearance as your original control box and remote. Verify that the numbers on the side of the receiver are identical to ensure proper compatibility with your specific children's riding toy. If your original remote control or receiver has "FC" written, please choose an "FC” remote control or receiver for compatibility.
2. Setup & Installation
2.1 Remote Control Battery Installation & Frequency Matching
- Battery Installation: Install two AAA 1.5V batteries into the remote control. Pay close attention to the positive and negative polarity inside the battery chamber. Close the battery cover securely. The indicator light will flash three times, confirming correct battery installation.
- Initiate Pairing: Press and hold the frequency key (often labeled 'car select' or 'S' for speed) on the remote control for approximately 2 seconds. The indicator light on the remote will begin to flash.
- Power On Vehicle: Turn on the power supply of the electric ride-on car. The indicator light on the remote control should turn off, indicating successful frequency matching.
- Troubleshooting Pairing: If the frequency matching is unsuccessful (the indicator light does not turn off), turn off the power supply of the car and repeat steps 2 and 3.
2.2 Control Box Wiring Diagram
Refer to the diagram below for proper connection of the control box to your electric ride-on toy's components. Ensure all connections are secure before operating the vehicle.
- Steering Motor: Connect to the designated port.
- Drive Motor 1 & 2: Connect to the respective drive motor ports.
- Power Supply: Connect the main power supply to the indicated port.
- 7-Pin Connector: This connector manages the following functions:
- High/low speed switch (Yellow wire)
- Forward (Orange wire)
- Back (Blue wire)
- Ground wire (Black wire)
- Power Output (Red wire)
- Battery positive (Red wire)
3. Operating Instructions
3.1 Remote Control Functions
The 2.4G Bluetooth remote control provides full command over the electric toy car:
- ▲ (Up Arrow): Forward movement.
- ▼ (Down Arrow): Backward movement.
- ◀ (Left Arrow): Turn left.
- ▶ (Right Arrow): Turn right.
- S (Speed): Adjusts the speed setting (e.g., high/low speed).
- P (Emergency Brake): Press this button to immediately stop the running function of the car. Press it again to release the brake and resume normal operation.
The RX19 control box includes a built-in slow start function, ensuring a smooth acceleration for the toy car.
3.2 Power Saving Mode
The remote control will enter a power-saving mode if left without operation for 10 seconds. The indication light will turn off to conserve battery life.
4. Maintenance
- Cleaning: Wipe the control box and remote control with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.
- Storage: Store the components in a dry place, away from direct sunlight and extreme temperatures.
- Battery Replacement: Replace the remote control batteries when the indicator light fails to flash or the remote's range decreases. Refer to section 2.1 for battery installation instructions.
- Moisture: Keep the control box and remote control away from water and moisture to prevent damage to electronic components.
5. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote control not responding / Indicator light not turning off after pairing. | Unsuccessful frequency matching or low remote battery. | Ensure remote batteries are correctly installed and charged. Repeat the frequency matching steps (Section 2.1). |
| Car not moving after control box installation. | Incorrect wiring, faulty motors, or depleted car battery. | Check all wiring connections against the diagram (Section 2.2). Verify that the car's motors and battery are functioning correctly. |
| Remote control indicator light off after 10 seconds. | Remote control entered power saving mode. | This is normal operation. Press any button to reactivate the remote. |
6. Specifications
| Feature | Detail |
|---|---|
| Model Number | RX19 12V |
| Voltage | 12V |
| Control Type | 2.4G Bluetooth Remote Control |
| Material | Plastic |
| Origin | Mainland China |
| Recommended Age | 3-6Y, 6-12Y, 14+y |
| Use | Vehicles & Remote Control Toys |
| Certification | CE, FCC |
| Is Electric | No Battery (refers to the control box itself) |
| Battery/Power Supply | N (Not included for control box) |
| Charger/Adapter | N (Not included) |
| High-concerned chemical | None |
7. User Tips
- Compatibility Check: Always double-check the appearance and model numbers (e.g., "RX19" or "FC" markings) on your original control box and remote to ensure the new part is a perfect match.
- Test Before Final Assembly: After wiring, perform a quick test of the remote control and car functions before fully reassembling the toy.
- Battery Polarity: Be extra careful when installing batteries in the remote control to observe correct positive and negative polarity.
8. Safety Information & Compliance
⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
This product is certified with CE and FCC standards.
9. Warranty & Support
For any issues, questions, or support regarding your Weelye RX19 control box and remote control, please contact the seller or refer to the store's official support channels. Keep your purchase records for any warranty claims.