DemonFX KING OF DRIVE

Contents

Demonfx King Of Drive Overdrive Pedal User Manual

Model: KING OF DRIVE

1. Introduction

The Demonfx King Of Drive is a versatile guitar effect pedal designed to provide a wide range of overdrive and distortion tones. Based on the Analogman King Of Tone, this monoblock effect pedal offers two independent channels, each with flexible tone-shaping capabilities through external controls and internal DIP switches. It allows musicians to achieve sounds from subtle clean boosts to rich, saturated distortion.

Front view of the Demonfx King Of Drive pedal

Front view of the Demonfx King Of Drive pedal, showcasing its controls and footswitches.

2. Features

  • Dual-channel overdrive/distortion pedal.
  • Inspired by the Analogman King Of Tone.
  • Independent Volume (V), Drive (D), and Tone controls for each channel.
  • Internal 4-position DIP switch for selecting Clean, Overdrive (OD), or Distortion modes for each channel.
  • Internal TREBLE knob for fine-tuning high frequencies.
  • Internal Hi Gain Switch (HIGH/NORM) for each channel to adjust gain levels.
  • True bypass switching for signal integrity.
  • Durable metal casing.

3. Controls and Indicators

Angled view of the Demonfx King Of Drive pedal

Angled view of the pedal, showing the layout of controls.

External Controls:

  • V (Volume) Knobs: Controls the output level of each channel.
  • D (Drive) Knobs: Adjusts the amount of overdrive/distortion for each channel.
  • Tone Knobs: Shapes the tonal character of each channel.
  • Footswitches: Two independent footswitches to engage/bypass each channel.
  • LED Indicators: Two LEDs (blue and red) indicate when each channel is active.
  • IN Jack: 1/4" mono input for your instrument.
  • OUT Jack: 1/4" mono output to your amplifier or next pedal.
  • 9VDC Input: Power input for a 9V DC adapter.

Internal Controls (Requires opening the pedal):

  • 4-Position DIP Switch: Configures the operating mode (Clean, OD, Distortion) for each channel.
  • TREBLE Knob: An internal trim pot to boost or cut treble frequencies.
  • Hi Gain Switch (HIGH/NORM): Internal switches to select between high gain and normal gain for each channel.

4. Setup

4.1 Power Connection

The King Of Drive pedal requires a regulated 9V DC power adapter. Ensure the adapter has a center-negative polarity and provides at least 100mA of current. Connect the adapter to the 9VDC input jack on the top of the pedal.

Rear view of the Demonfx King Of Drive pedal with power requirements

Rear view of the pedal, indicating 9VDC center negative power requirement.

4.2 Audio Connections

  1. Connect your guitar or other instrument to the IN jack on the right side of the pedal.
  2. Connect the OUT jack on the left side of the pedal to your amplifier or the input of the next effect pedal in your signal chain.

4.3 Initial Internal Settings

The pedal features internal DIP switches and a TREBLE knob that allow for extensive customization of its sound. To access these, you will need to carefully open the pedal casing. The factory default DIP switch setting is typically ON OFF OFF OFF (Switches 1, 2, 3, 4 respectively, where ON is up and OFF is down). This sets the RED (right) channel to Overdrive (OD) mode and the YELLOW (left) channel to Clean mode.

5. Operating Modes (DIP Switch Settings)

The Demonfx King Of Drive features a 4-position DIP switch inside the pedal, allowing you to select between Clean, Overdrive (OD), or Distortion modes for each of its two channels (Red/Right and Yellow/Left). This provides significant flexibility in tailoring your sound.

Internal DIP switch diagram for Demonfx King Of Drive pedal

Detailed diagram of the internal DIP switches and their corresponding modes.

DIP Switch Configuration:

  • There are 4 DIP switches. Switches 1 and 2 control the RED (right) channel. Switches 3 and 4 control the YELLOW (left) channel.
  • Switch Position: 'ON' typically means the switch is in the 'up' position, and 'OFF' means 'down'.

Mode Descriptions:

  1. Normal Overdrive (OD) Mode: This is the standard King Of Tone sound, offering a classic overdrive with less drive than a typical tube screamer. This mode can be significantly louder if desired (up to 4 times louder than a tube screamer). It also includes a Hi Gain switch for selecting between high gain and normal gain within this mode.
  2. CLEAN Mode: Provides less distortion, suitable for clean boosts or clearer, louder sounds. It acts as a cross between a true clean boost and an overdrive, offering less compression than the standard OD mode. This mode can get twice as loud as the OD mode.
  3. DISTORTION Mode: Offers more drive than the standard OD mode, with a touch of hard distortion. The sound is more compressed but retains the pedal's character. This mode can get almost twice as loud as a tube screamer. Note that Distortion mode is not available on either side with the factory DIP switch setting.

DIP Switch Settings for Channels:

The two left switches (1 and 2) are for the RED (right) side. The two right switches (3 and 4) are for the YELLOW (left) side, and function identically to the Red side switches.

  • For RED (Right) Channel (Switches 1 & 2):
    • Switch 1 (down): Clean mode.
    • Switch 1 (up): Overdrive (OD) mode.
    • Switch 2 (up): Activates DISTORTION mode. When Switch 2 is up, the position of Switch 1 is less critical but it's best to turn it OFF for clarity.
  • For YELLOW (Left) Channel (Switches 3 & 4): Function identically to Switches 1 and 2 for the Red channel.

Common Configurations:

  • Factory Setting (Red=OD, Yellow=CLEAN): ON OFF OFF OFF (Switch 1 ON, 2 OFF, 3 OFF, 4 OFF). This provides both OD and Clean modes available.
  • Both Channels OD Mode: ON OFF ON OFF.
  • Both Channels CLEAN Mode: OFF OFF OFF OFF.
  • Internal TREBLE Knob: Located inside the pedal for each side. Turn it all the way down for a normal setting, or adjust it up for brighter tones, especially with darker sounding guitars or amps.
  • Internal Hi Gain Switch: For each channel, select between HIGH or NORM gain.

It is generally recommended to set the right (Red) channel to be the more distorted side, as it comes before the left (Yellow) side in the signal path, allowing the left side to provide more boosting. Running a clean boost before an OD will add distortion but not much volume, while running a clean boost after an OD will add more volume without significantly changing the distortion.

6. Specifications

Attribute Value
Brand Name DemonFX
Model Number KING OF DRIVE
Type Effects (Overdrive, Multi-effects)
Hardware Interface AUX
Control Type Knob, Button
Power Supply 9V DC, 100mA, Center Negative
Batteries Included No
Dimensions (L x W x H) 13 cm x 9 cm x 8 cm (approx.)
Weight 0.45 kg (approx.)
Origin Hongkong (China)

7. Troubleshooting

  • No Sound:
    • Check all cable connections (instrument to IN, OUT to amplifier).
    • Ensure the 9V DC power adapter is correctly connected and functioning.
    • Verify that the amplifier is on and its volume is up.
    • Test with different cables or a different power supply if possible.
  • Weak or Distorted Sound (Unintended):
    • Check the power supply; insufficient power can cause issues.
    • Ensure instrument cables are not faulty.
    • Adjust the Volume (V), Drive (D), and Tone knobs.
    • Review internal DIP switch settings to ensure they match your desired mode.
  • Excessive Noise/Hum:
    • Use a high-quality, regulated power supply.
    • Ensure proper grounding in your setup.
    • Keep the pedal away from power transformers or other sources of electromagnetic interference.

8. User Tips

  • Verify Internal DIP Switch Settings: While the manual specifies a factory default of ON OFF OFF OFF, some users have reported receiving units with all DIP switches set to the 'down' (OFF) position. Always verify the internal DIP switch settings upon first use to ensure they align with your desired operating modes.
  • Experiment with Internal TREBLE Knob: Don't overlook the internal TREBLE knob. It can significantly impact the pedal's brightness, especially when paired with darker-sounding guitars or amplifiers. Adjust it subtly to find your sweet spot.
  • Channel Order for Boosting: For optimal results, consider setting the right (Red) channel for more distortion and the left (Yellow) channel for a clean boost. Placing the clean boost after the overdrive/distortion can add volume without altering the distortion significantly, while placing it before will increase distortion.

9. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the pedal's exterior. Avoid using abrasive cleaners or solvents.
  • Storage: Store the pedal in a dry environment, away from extreme temperatures and humidity.
  • Cable Care: Always handle audio and power cables carefully. Avoid bending them sharply or pulling them by the cable itself.
  • Internal Access: If you need to adjust the internal DIP switches or TREBLE knob, ensure the pedal is disconnected from power and audio sources. Exercise caution when opening the casing to avoid damaging internal components.

10. Warranty and Support

For detailed warranty information and technical support, please refer to the official Demonfx website or contact your retailer. A comprehensive user manual in PDF format is also available for download, which may contain additional information not covered here. You can typically find this by searching for "Demonfx King Of Drive manual PDF online" or checking the product page where you purchased the item.

A PDF version of the user manual is available at: Demonfx King Of Drive User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.