ISUDAR Carplay Module for Porsche PCM 3.1

Contents

ISUDAR Carplay Module User Manual

Authentic Products - Excellent Technology - Pleasant Ride

1. Product Overview

The ISUDAR Carplay Module is designed to upgrade your Porsche's original PCM 3.1 system, adding modern connectivity features like Apple CarPlay and Android Auto without replacing the factory head unit. This module supports non-destructive installation, preserving your original car's cables and functionality.

Key Features:

  • Supports Non-destructive installation.
  • Adds Apple CarPlay and Android Auto to the OEM screen.
  • Enables video playback on the car screen after installation.
  • Powerful SUNPLUS SPHE8368-U processor for enhanced performance.
  • Built-in 5GHz WiFi for stable and fast wireless connections.
  • Supports wired and wireless Apple CarPlay and Android Auto.
  • Mirror Link functionality for both iOS and Android devices.
  • USB Video and Music Playback from U-Disk.
  • Supports front and rear view camera input (cameras not included).
  • DSP Sound Processor with EQ adjustment.
  • Retains original camera and parking sensor support.
  • Supports steering wheel controls.

Compatibility:

This module is compatible with Porsche Cayenne/Panamera/Macan/Cayman/718/911 models from 2010-2016 with a 7-inch screen and PCM 3.1 system.

Note: If your car has a PCM 3.0 system (typically 2009-2012 Boxster/Cayman/Cayenne/911 with 7-inch screen), a different Carplay box is required. The PCM 3.0 Carplay box can only be used for automatic cars.

Porsche PCM 3.1 system

Image: Porsche PCM 3.1 system, indicating compatibility for Cayenne/Panamera/Macan/Cayman/718/911 2010-2016 with 7-inch screen.

Porsche PCM 3.0 system

Image: Porsche PCM 3.0 system, for reference to distinguish from PCM 3.1.

Video: Demonstration of the ISUDAR Carplay Module in a Porsche, showcasing CarPlay interface, navigation, music, phone calls, settings, and camera views.

2. Setup and Installation

2.1. Accessories Included:

The package includes the following components:

Accessories included in package

Image: All accessories included in the package.

  • RCA & USB Cable
  • Power Cable
  • Data Cable
  • Microphone
  • Installation Guide (physical document)
  • FFC (Flexible Flat Cable)
  • BT & WIFI Antenna
  • Copper Column Screws
  • Transfer cables

2.2. Installation Steps:

Step 1: Remove the OEM Radio

  • Remove the 3 screws at the rear of the radio and the 2 screws at the bottom.
  • Use tweezers to press down the left and right shrapnel on the lower side, and push the DVD drive out, then extract it upwards.
  • Note: Do not be forced when pulling up, otherwise the FPC cable will be damaged.
Removing OEM radio

Image: Illustration of removing the OEM radio unit.

Step 2: Prepare for Module Installation

  • To remove the FPC cable: Pull up on the buckles on each side of the DVD drive FPC slot and remove the FPC cable. In the same way, take out the two FPC cables of the display.
  • Note: Be careful not to pull the buckles too hard, otherwise the slot will be damaged.
  • Install the copper post screws to the 3 screw holes on the radio motherboard. Select the length of the screw column as required. If necessary, you can even connect the long and short screw columns together.
  • Unscrew the bezel on the back of the radio, remove the bezel and thread the WiFi & Bluetooth Antennas and Transfer cables into the hole.
Preparing for module installation

Image: Preparing the radio unit for module installation, showing FPC cable removal and screw installation.

Step 3: Connect the Module

  • Plug the FPC cable into the radio motherboard, and plug the Wifi&Bluetooth Antenna into the module's motherboard.
  • Place the module's motherboard and lock it with screws.
  • Note: When plugging in the WiFi&Bluetooth Antenna, do not slant it or push too hard.
  • Insert the monitor FPC cables and the module's FPC cables to the corresponding position of the module's motherboard.
  • Note: The FPC cables must be inserted in the right direction, not obliquely. The buckles must be pressed flat, otherwise the machine will not boot or may be damaged.
Connecting the module

Image: New version PCB board installed on the original radio motherboard.

Step 4: Final Connections and Testing

  • Plug the Transfer cables with the power cable and RCA & USB Cable.
  • Plug the power into the radio socket and the car power cable into the car power cable socket.
  • Open the car key and check radio displaying. Press and hold the "INFO" button for 3 seconds to enter the main interface.
  • No sound is normal at this time. If it does not turn on or cannot enter the interface, please check the FPC and connections.
  • Note: The WiFi & Bluetooth Antenna cannot be bent, and should not be bundled with the power cable, otherwise the signal will be attenuated.
  • Insert the DVD Driver FPC cable into the radio motherboard socket, install the DVD Driver, and lock all the screws.
  • Note: When pushing back the DVD Driver, please organize all the FPC cables, do not break them. The left and right metal shrapnel should be careful to press and be snapped back to their original positions.
  • If the car has OEM fiber optic cable, take out the fiber optic cable and install it into the correct position on the power connector.
  • Note: When installing the fiber optic cable, pay attention to the direction and do not insert it into the wrong hole, otherwise there will be no sound.
New version circuit board with DAC+Operational Amplifier chips

Image: New version circuit board with DAC+Operational Amplifier chips for improved sound quality.

3. Operating Instructions

3.1. Apple CarPlay Connection:

Wired Connection:

  • Insert the USB data cable into your iPhone. It will automatically enter the wired CarPlay interface.
  • The iPhone interface will display a dialog box. Click to allow and enable wireless CarPlay according to the prompts.
  • Wait for 15 seconds, then unplug the USB data cable. It will automatically connect to wireless CarPlay.
Apple CarPlay wired connection

Image: Phone connected wirelessly to the car display via CarPlay.

Wireless Connection:

  • From the main interface, go to Settings > WiFi CarPlay Setting > Discover and connect devices.
  • Search for your iPhone and connect.
  • Click and pair on the Bluetooth interface on the iPhone. Complete the pairing and enable CarPlay as prompted.
  • The system will enter the wireless CarPlay interface.
Apple CarPlay wireless connection

Image: Wireless CarPlay feature, showing a phone connected wirelessly to the car display.

3.2. Android Auto Connection:

Wired Connection:

  • If your Android mobile doesn't have Android Auto, download the Android Auto APP on your mobile.
  • Click the "Android" icon on the main menu, connect the USB data cable to your mobile, then it will enter Android Auto automatically.
  • If your mobile supports wireless Android Auto, wait for 15 seconds then unplug the USB data cable. It will automatically connect to wireless Android Auto.
Android Auto wired connection

Image: Android Auto feature, showing a phone connected via USB to the car display.

Wireless Connection:

  • If your mobile supports wireless Android Auto, go to Settings > Wireless Android Auto Settings > Pairing.
  • Pair on the Bluetooth on your mobile phone.
  • Note: Wireless connection only supports a part of Pixel and Nexus phones.
Android Auto wireless connection

Image: Android Auto wireless connection setup.

  • Supports USB data cable connection.
  • Supports both iOS and Android systems.
Mirror Link feature

Image: Mirror Link feature, showing a phone mirroring its screen to the car display.

3.4. USB Video and Music Playback:

  • Supports U-Disk connection.
  • You can play video and music files directly from a USB drive on your factory screen.
USB Video & Music Playback

Image: USB Video & Music Playback feature, showing a USB drive connected and video playing on the car display.

3.5. Button Operations:

The module integrates with your car's existing controls. Here are the functions:

Car's control knob and steering wheel

Image: Car's control knob and steering wheel, indicating support for original controls.

Steering wheel controls and Siri voice assistant

Image: Steering wheel controls and Siri voice assistant on the car display.

  1. Answer and make calls
  2. Short press to hang up, long press to open SIRI voice
  3. Short press to return, 10 seconds long press to force the system to upgrade
  4. Last
  5. Turn left and right to adjust the volume, 10 seconds long press to reset system
  6. Audio channel switching
  7. Next
  8. Answer the phone
  9. Long press to switch system
  10. Hang up the call
  11. Turn left and right to select, press to confirm
  12. Short press to return, 10 seconds long press to force the system to upgrade

3.6. Other Settings:

  • Change Language: Go to Settings > Languages to choose your preferred language.
  • Change Driver Position: Go to Settings > UI Settings > Driver Position.
  • Checking Software Version: Go to Settings > Information > About Version.
  • Update MCU or System: Go to Settings > Information > About device > Update.

4. Rear View Camera Connection and Settings

The ISUDAR Carplay Module supports both OEM and aftermarket cameras.

Car camera inputs diagram

Image: Diagram showing car camera inputs (front and rear view cameras).

4.1. OEM Camera:

  • If your car has an OEM camera, you do not need to make additional connections or settings; the module will support it well.

4.2. Aftermarket Camera:

For installing an aftermarket camera, follow these steps:

  • AV Plug Connection: Connect the AV plug of the camera to the "REAR_CVBS" port on the RCA & USB Cable. The camera signal will be fed into the Mainboard from here.
  • Red Power Cable: Connect the red power cable of the camera to the "CAM_12V" cable on the RCA & USB Cable. When the car is in reverse gear, "CAM_12V" will provide 12V power to turn on the camera.
  • Black GND Cable: Connect the black GND cable of the camera to the GND of the car or the metal body.
  • Settings: Go to Main menu > Settings > Advanced Features. Set "Aftermarket Camera" to OFF. For AHD cameras, you need to set the AHD Camera type.

5. External Microphone Setting

We recommend using the external microphone provided with the module, as only this microphone can utilize the Siri function.

  • Insert the external microphone into the "MIC" socket of the power cable.
  • Place the microphone on the roof above the driver's seat.
  • Settings: Go to Main menu > Settings > Audio Settings. Set "Original MIC" to OFF.
  • Open "Automatic echo cancellation" (optional) and follow the prompts.
  • Note: There will be ZZ noise during echo cancellation, this is normal.

6. Specifications

AttributeValue
Brand NameISUDAR
CategoryCarplay adapter
DinOne Din
Display Size2.5" (Refers to the module's internal display handling, not the car's screen size)
Processor Speedfast
ChipsetSUNPLUS SPHE8368-U (ARM Cortex-A9)
Special FeaturesBuilt-in GPS, Mobile Phone (integration)
Digital Media FormatCD (for AUX activation)
OSD LanguageChinese (Simplified), Polish, German, Russian, Dutch, Portuguese, Turkish, English
For Vehicle Brands/ModelPORSCHE (Panamera, Cayenne, Macan, Cayman, Boxster, 911, 718 with PCM 3.1)
CertificationCE
Wireless CarplaySupport
Wireless Android AutoSupport
Mirror LinkSupport
Bluetooth & WIFISupport (5GHz WiFi)
Rear CameraSupport
OEM Parking SensorSupport
External MicrophoneSupport
Built-in DVD PlayerNo
Built-in CD playerNo
Is touch screenNo
Built-in ScreenNo

7. Troubleshooting (FAQ)

7.1. No Sound, All Connections OK:

  • Go to the OEM settings menu, find the audio settings, and select both AUX and AUX Bluetooth.
  • When playing sound through CarPlay, select the AUX channel on the OEM interface.
  • If there is no AUX option: Place a CD in the CD player and let it play. Select CD as your source and play as normal. Press the Options button, and a new hidden window will appear. Press the check box that says AUX to activate the port.
  • If AUX is chosen but there is still no sound:
    • If the DISC can be read, the optical fiber of the original car may not be plugged in properly.
    • If the DISC cannot be read, the DVD Driver may not be installed properly.

7.2. Screen is Black when Long Pressing "INFO" Button:

  • Check if the FPC cables are firmly inserted and fastened.
  • Verify that the FPC cables are not damaged or installed backwards.

7.3. Wireless Android Auto or CarPlay Cannot Connect:

  • Confirm whether your mobile phone supports wireless connection. Note that only some Pixel and Nexus mobile phones support wireless connection from Android 11 version.
  • Insert the USB data cable and use the wired link. It should automatically switch to wireless after 10-15 seconds.

7.4. FPC Cable or Antenna Damaged:

  • Please contact customer service with your order number for replacement accessories.

7.5. Original Car Interface is Easy to Shake:

  • Ensure the FPC cables are securely plugged in.

8. User Tips

  • For optimal sound quality, ensure both AUX and AUX Bluetooth are selected in the OEM audio settings.
  • When installing, handle FPC cables and antennas with care to avoid damage and ensure proper functionality.
  • If you experience issues with the return button on the steering wheel control interfering with CarPlay, contact customer service for a software update.
  • Adjust the MIC Sensitivity and EQ settings in the Audio Settings for personalized sound and microphone performance.
  • Explore the UI Settings to customize the Driver Position and Wallpaper for a tailored user experience.

9. Maintenance

  • Keep the module and connections free from dust and moisture.
  • Avoid exposing the unit to extreme temperatures.
  • Regularly check cable connections to ensure they are secure.
  • Clean the screen with a soft, dry cloth. Do not use harsh chemicals.

10. Warranty and Support

10.1. Warranty:

This product comes with a one-year warranty.

10.2. Customer Support:

For any technical assistance, troubleshooting, or warranty claims, please contact ISUDAR customer service. Provide your order number for efficient support.

If you need to update the MCU or system software, go to Settings > Information > About device > Update. For specific updates or issues with steering wheel controls, contact customer service for software version information and update methods.

11. Regulatory Information

FCC STATEMENT:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

This device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

NOTE: This device and its antenna(s) must not be co-located or operate in conjunction with any other antenna or transmitter.

RF EXPOSURE STATEMENT:

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operate in conjunction with any other antenna or transmitter.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.