Important Safety Instructions
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
- Read all instructions before using.
- In case of emergency, immediately unplug the machine from the power outlet.
- Check that the voltage indicated on the rating label of the appliance does in fact match that of your electrical system.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience, and knowledge, unless they are supervised or instructed concerning the use of the appliance by a person responsible for their safety. Never leave the appliance unattended during operation. Keep it out of the reach of children.
- Do not operate the appliance with a damaged cord or plug or after the appliance malfunctions, has been dropped or damaged in any manner. Return the appliance to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
- Always unplug the appliance when not in use or before cleaning. Allow it to cool before adding or removing parts, and before cleaning the appliance.
- To protect against fire, electric shock and personal injury, do not immerse cord, plug or appliance in water or other liquid. Never clean the appliance or the power cord if they are humid. Avoid touching the appliance with wet hands.
- Do not run the cord under carpeting. Do not cover the power cord with throw rugs, runners or similar floor coverings. Arrange the cord away from high traffic areas to a place where it will not be tripped over.
- Avoid the use of an extension cord as it may overheat and become a fire hazard. If you must use an extension cord, it should be rated no less than 1,000 watts. Only use a grounded socket to connect the appliance.
- Do not place on or near a hot gas or electric burner, or in a heated oven.
- It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet receptacle and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlets.
- Use the appliance only as the described in this manual. Any other use or accessory attachments not recommend by the manufacture may cause fire, electric shock, or injury.
- Never wash in the dishwasher or immerse the machine into water.
- Only use the milk frother with the power base provided. Do not use the power base with anything else.
- Do not operate without milk in the jug. Do not insert any object or fingers into the jug when operating. Do not overfill the jug. Filling past the maximum levels indicated inside the jug can cause overflowing during operation. Never touch rotating parts. Risk of injury!
- This appliance is intended to be used in household (indoor) and similar applications such as: staff kitchen areas in shops, offices and other working environments like farm houses; by clients in hotels, motels. No liability is accepted for any damage resulting from use for other purposes, faulty operation or amateur repairs.
Product Overview
Familiarize yourself with the components of your HiBREW M3A Milk Frother:
- Milk Frother Unit: The main body with a stainless steel jug, control panel, and handle.
- Rotatable Base: The power base for the frother unit.
- Stirrers (2 pcs): One whisk for frothing milk and one for heating milk.
- Cleaning Brush: For easy cleaning of the frother.
- Instruction Manual: This document.
- Packaging Box: For storage and transport.
The frother features a removable cup design, allowing the cup to be separated from the base and rotated 360 degrees for user-friendly operation.
Specifications
| Attribute | Value |
|---|---|
| SKU | M3A |
| Brand Name | HiBREW |
| Model Number | M3 |
| Rated Voltage & Frequency | AC 220-240V, AC100~120V, 50/60Hz |
| Rated Power | 450W |
| Power (W) | <750W |
| Capacity (Froth) | Max. 130ml |
| Capacity (Heat and Stir) | Max. 330ml |
| Rotation Rate (RPM) | 4800 |
| Style | Standing |
| Power Type | Electric |
| Certification | CB |
| Origin | Mainland China |
| Package Size | 137*133*196mm |
| Net Weight / Gross Weight | 0.95kg / 1.15kg |
The frother is designed for precise temperature control, automatically stopping when the set temperature is reached to prevent dry burning.
The temperature range for heating milk/frothed milk is 60°C±5°C.
The product supports various plug types for different regions:
- EU Plug: 220V~240V
- UK Plug: 220V~240V
- US Plug: 110V~120V
Setup and First Use
Before The First Use
- Unpack the box with care, remove all the packing materials away from the appliance and keep it for later use.
- Keep the packing material (bag and etc.) away from children for safety.
- Before using the appliance for the first time, please clean the jug and the accessories as described under the chapter “Cleaning and maintenance” to remove the dust or production residues.
Operating Instructions
Function Definition
The HiBREW M3A Milk Frother offers 4-in-1 functionality for various milk preparations:
| Whisk | Function | LED Color | Operating Mode | Temperature (°C) | Maximum Volume |
|---|---|---|---|---|---|
 | Super Hot | Red | Super Hot: heating and frothing | 70~80°C | 150ml |
| Normal Hot | Red | Normal Hot: heating and frothing | 60~70°C | 150ml | |
| Warm | Red | Warm: heating and frothing | 50~60°C | 150ml | |
| Cold | Blue | Cold: frothing without heating | Room temperature | 150ml | |
| Super Hot | Red | Super Hot: heating and frothing | 70~80°C | 300ml |
| Normal Hot | Red | Normal Hot: heating and frothing | 60~70°C | 300ml | |
| Warm | Red | Warm: heating and frothing | 50~60°C | 300ml | |
| Cold | Blue | Cold: frothing without heating | Room temperature | 300ml |
Note: The data in this table were provided by lab in accordance to certain brand milk/Chocolate, local milk/Chocolate from different countries may be various and get different temperature as well as volume, you should take these data for reference only, not criteria.
Quick Steps
Follow these simple steps for quick preparation:
- Install the milk frothing whisk.
- Add the milk (do not exceed the MAX line inside the machine when frothing milk, or the MAX line when heating milk).
- Select the desired mode by pressing the power button.
- Enjoy creamy milk froth.
Detailed Operating Steps
- Choose the proper whisk and insert it inside the jug.
- Pour desired milk into the jug but not more than the maximum to avoid overflow.
- Press the on/off button to turn the appliance on.
- When Pressed the on/off button within 3 seconds and the unit is turned on, user can press On/Off button to choose desired heating mode indicated with the LED display.
- The default heating mode is Normal heating.
- Once the heating mode is selected, the flashing LED display turns to a solid light and the selected heating mode starts.
- The milk frother will switch off automatically.
- The operating can be cancelled by pressing the On/Off button again during working.
Product Demonstration Video
This video demonstrates the frother's operation, including preparing hot cappuccino and cold frothed milk for iced coffee.
Tips for Easy Drinks
The HiBREW M3A Milk Frother allows you to create a variety of delicious beverages:
| With Frothed Milk | With Hot Milk | ||
|---|---|---|---|
 Cappuccino | 1/3 Espresso 2/3 frothed milk Some cocoa powder |  Caffe Latte | 1/3 Espresso shot 2/3 heated milk and stir |
 Latte Macchiato | Pour desired frothed milk into a tall glass Add espresso carefully along the rim of the glass |  Protein powder | Add water first then add protein powder |
 Hot Chocolate | Add milk first then add chocolate powder |  Instant coffee drinks | Make instant coffee Add frothed milk inside |
Cleaning and Maintenance
Unplug from the power before cleaning, remove the lid from the jug.
Never immerse the jug or base into water. This device is NOT designed for dish-washer.
- The jug & base: Clean the jug immediately after each use, flush and clean the wall and bottom with warm soapy water and use the brush to clean the residue if there is. Never use sharp object such as metal brush and never use abrasives cleaning agent to clean the surface to avoid scratches. Then dry with a soft cloth.
- The lid: Rinse under water directly.
- The whisks: Remove from the jug and wash with warm water. Dry and store in a safe place in case of missing.
Troubleshooting
If you encounter any issues with your HiBREW M3A Milk Frother, please refer to the table below for common problems and solutions:
| Problems | Causes | Solutions |
|---|---|---|
| Indicator light doesn't work or jug doesn't work | Plug is not inserted properly | Re-insert into the power |
| Jug and power base not connected properly | Remove the jug and place again on the base | |
| No power in the socket | Check the electric circuit | |
| Problems with electric elements | Repair | |
| Jug ceases to work after starting operation | Jug temperature is too high | Rinse cold water inside the jug to reduce the temperature |
| Jug damaged with immersion in water | Repair | |
| Motor doesn't work | Jug is not cleaned in time after use, milk locks the mechanism | Clean and move the shaft sleeve of motor by hand to loosen it |
| Motor damage | Repair | |
| No heating | Machine damage | Repair |
| Charring | Dosage of milk either too little or too much | Use the dosage of milk according to the dial |
| Jug reused without cleaning | Cleaning in time after use | |
| Actual voltage much lower than specified voltage | Use the appropriate voltage | |
| Quality of milk froth not up to standard | Wrong milk type or temperature | Make sure to use whole or semi-skimmed milk at refrigerator temperature (about 6-8°C) |
| Wrong whisk used | Make sure to use the appropriate whisk | |
| Jug reused without cleaning | Make sure the jug is clean | |
| Four lights are on, and the machine doesn't work | NTC short circuit or open circuit | Contact a professional for maintenance |
| The three lights flash for five times and then go out, and the machine does not work. | The machine temperature is too high, and it has entered the overheat protection program. | After adding cold water to the machine, the temperature of the machine decreases and it can be used normally. |
User Tips
- For best frothing results, use whole milk with a fat content of 3.0% or above. Ensure the whisk is correctly installed and undamaged.
- The frother offers various temperature settings. For very hot beverages, select the 'Super Hot' mode (70-80°C). The 'Cold Frothing' mode operates at room temperature, not chilled.
- If the frother stops working or shows no indicator light, first check if the plug is properly inserted and if the power base is correctly connected to the jug. Refer to the troubleshooting section for further steps.
- To prevent milk leakage, always ensure you do not overfill the jug beyond the indicated MAX lines for frothing or heating.
- The HiBREW M3A supports both 220-240V and 100-120V electrical systems, and works with both 50Hz and 60Hz frequencies. Ensure you select the correct plug type for your region (EU, UK, or US).
- After each use, especially after heating, it's recommended to rinse the jug with cold water or wait a few minutes for the internal thermostat to reset before preparing another batch.
Warranty and Support
For warranty claims, technical support, or service inquiries, please contact the manufacturer directly:
- Manufacturer: FOSHAN SHUNDE BENE APPLIANCE TECH CO.,LTD
- Address: Huicong Electric Appliance Zone, Beijiao Town, Shunde District, Foshan City, Guangdong, China.
- Service Info: support@hibrew.com
Please retain your purchase receipt as proof of purchase for any warranty claims.
