Introduction
This manual provides comprehensive instructions for the setup, operation, and maintenance of your Anytone AT-708 Plus CB Radio. Please read this manual thoroughly before operating the device to ensure proper functionality and safety.
The Anytone AT-708 Plus is a compact Citizen Band (CB) mobile radio designed for reliable communication. It operates on frequencies between 24.265-29.655MHz, supporting both AM and FM modulation modes, with an output power of 8W.

Figure 1: Anytone AT-708 Plus CB Radio with attached microphone.
Package Contents
Upon unpacking, please verify that all items listed below are present and in good condition:
- Anytone AT-708 Plus CB Radio Unit
- Microphone with coiled cord
- Mounting Bracket
- Power Cable (red and black wires)
- Mounting Screws and Washers
- User's Manual (this document)

Figure 2: Contents of the Anytone AT-708 Plus CB Radio package, including the radio unit, microphone, mounting bracket, power cable, and user manual.
Setup Instructions
- **Connect the Microphone:** Screw the microphone plug firmly into the microphone connector on the front panel of the radio.
- **Connect the Antenna:** Ensure your external antenna is securely connected to the antenna connector (UHF, SO-239 type) on the rear panel of the radio. A properly matched antenna is crucial for optimal performance and to prevent damage to the radio.
- **Connect Power:** Connect the red wire of the power cable to the positive (+) terminal of your vehicle's 12V DC power source, and the black wire to the negative (-) terminal or chassis ground. Ensure the connection is secure and properly fused.
- **Initial Squelch Setting:** Turn the SQUELCH control knob fully clockwise. This will set the squelch to its maximum level, muting any background noise.

Figure 3: Rear view of the radio, highlighting the antenna connector and power cable connection point.
Operating Your Radio
Follow these steps to operate your Anytone AT-708 Plus CB Radio:
- **Power On and Volume Adjustment:** Turn the ON/OFF VOL knob clockwise to power on the unit and adjust the desired listening volume.
- **Select Channel:** Use the CHANNEL knob on the left side of the front panel to select your desired channel. Alternatively, use the UP/DN buttons on the microphone to change channels.
- **Change Band:** Press the "BAND" button on the front panel to cycle through available frequency bands.
- **Select Modulation Mode (AM/FM):** Press the "AM/FM" button on the front panel to switch between Amplitude Modulation (AM) and Frequency Modulation (FM) modes.
- **Scan Function:** Press the "SCAN" button to activate the channel scan feature. The radio will automatically scan through channels until a signal is detected. Press "SCAN" again to stop scanning.
- **Transmit:** To transmit, press and hold the Push-To-Talk (PTT) button on the microphone and speak into the microphone in a normal tone of voice.
- **Receive:** To receive incoming transmissions, release the PTT button.
Video 1: Demonstration of basic operations including volume adjustment, channel changing via knob and microphone, band selection, AM/FM mode switching, scan function, and PTT button usage on the Anytone AT-708 Plus CB Radio.
Specifications
| Feature | Specification |
|---|---|
| GENERAL | |
| Modulation Mode | AM/FM |
| Frequency Range | 24.265-29.655MHz |
| Frequency Tolerance | ±5.0 ppm |
| Input Voltage | 13.2 V DC ± 15% |
| Dimensions | 140x195x37mm |
| Weight | 656g |
| Operating Temperature Range | -20℃ to +50℃ |
| Current Drain | Transmit: 3A MAX; Receive: Squelched 0.3A; VOL Max: 0.7A |
| Antenna Connector | UHF, SO-239 |
| RECEIVER | |
| Sensitivity | Less than 1uV for 10dB(S+N)/N |
| Adjacent Channel Rejection | 60dB |
| IF Frequencies | 1st 10.695MHz, 2nd 455KHz |
| Automatic Gain Control (AGC) | Less than 10dB change in audio; Output for inputs from 10 to 50000uV |
| Squelch | less than 1uV |
| Audio Output Power | 1Watts at 8Ω less than 10% distortion |
| Frequency Response | 300-3000 Hz |
| TRANSMITTER | |
| Power Output | 8 Watts FM/AM |
| Frequency Response | 300-3000 Hz |
| Modulated Signal Distortion | inferior to 5% |
| Output Impedance | 50 ohms |

Figure 4: Detailed technical specifications for the Anytone AT-708 Plus CB Radio.

Figure 5: Band and Frequency List for the Anytone AT-708 Plus CB Radio, showing 480 AM-FM channels across various bands.
Maintenance
To ensure the longevity and optimal performance of your Anytone AT-708 Plus CB Radio, consider the following general maintenance tips:
- Keep the radio clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
- Avoid exposing the radio to extreme temperatures or direct sunlight for prolonged periods.
- Ensure all connections (antenna, power, microphone) are secure and free from corrosion.
- Do not attempt to open the radio casing or perform internal repairs, as this may void the warranty and cause damage.
Specific maintenance schedules or procedures are not detailed in the provided product information. For any issues requiring service, please contact customer support.
Troubleshooting
General troubleshooting steps for common issues:
- **No Power:** Check power cable connections, vehicle's fuse, and ensure the ON/OFF VOL knob is turned on.
- **No Reception/Poor Reception:** Verify antenna connection, check squelch setting (ensure it's not too high), and try changing channels or bands.
- **No Transmission:** Ensure the microphone is properly connected and the PTT button is being pressed firmly.
If you encounter persistent issues not resolved by these steps, please refer to the warranty and support information below.
Warranty and Support
The Anytone AT-708 Plus CB Radio comes with a 12-month warranty for the main unit. Accessories are covered for 6 months.
Return Policy:
- All returned items MUST be in their original condition, including the box, packaging, and all other accessories.
- Returns should be sent via POST AIR MAIL and declared as "sample" with a value of "US$10.00".
- If the item is defective within 30 days of receipt, the seller will bear one-way shipping fees for warranty service.
- If defective after 30 days of receipt, buyers are responsible for all extra shipping fees.
Customer Support:
For any problems or inquiries, please contact customer support immediately. The seller aims to respond within 24 hours and work with you until you are satisfied. Please do not open a dispute before communicating with customer support.

Figure 6: Service Policy outlining shipping, warranty, and return details.

Figure 7: Feedback policy, emphasizing communication before opening disputes and encouraging 5-star ratings.