FGHGF for proscenic 830P 800T 820S 830T 830Tviper520

Contents

FGHGF Vacuum Cleaner Charging Base Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your FGHGF Vacuum Cleaner Charging Base. This charging base is designed as a replacement part for various Proscenic robot vacuum cleaner models, including 830P, 800T, 820S, 830T, and Viper 520.

Front view of the FGHGF Vacuum Cleaner Charging Base
Front view of the FGHGF Vacuum Cleaner Charging Base.

2. Safety Information

California Proposition 65 Warning: This product contains Abiraterone acetate, a chemical known to the State of California to cause female reproductive toxicity and developmental toxicity and male reproductive toxicity. For more information go to www.P65Warnings.ca.gov

Always ensure the charging base is placed on a stable, flat surface away from water or excessive heat. Disconnect power before cleaning or performing any maintenance.

3. Specifications

AttributeValue
Brand NameFGHGF
Model Numberfor proscenic 830P 800T 820S 830T 830Tviper520
MaterialMetal, ABS Plastic
OriginMainland China
TypeVacuum Cleaner Parts
Vacuum Part TypeBRUSHES (Note: This property is listed in the product data, but the item is a charging base.)
Compatible Models (Type 1)for proscenic 830P 800T 820S Charging Base
Compatible Models (Type 2)for proscenic 830P 800T 820S robot parts
Compatible Models (Type 3)for proscenic 830P 800T 820S Charger base
Compatible Models (Type 4)for proscenic 830P 800T 820S Accessories
Compatible Models (Type 5)for proscenic 830P 800T 820S brush engine
Compatible Models (Type 6)for viper 520 charging base
Compatible Models (Type 7)for proscenic 830T charging base
Package Length20 cm
Package Width18 cm
Package Height18 cm
Package Weight0.27 kg

4. Package Contents

Verify that all items are present and in good condition upon opening the package.

  • 1x FGHGF Vacuum Cleaner Charging Base

5. Setup Instructions

5.1. Choosing a Location

Select a flat, stable surface for the charging base. Ensure there is ample clear space (approximately 1 meter / 3 feet) on both sides and in front of the base to allow the robot vacuum to dock easily. The location should be near a power outlet and away from direct sunlight or heat sources.

Front view of the charging base showing charging contacts
Front view of the charging base, highlighting the charging contacts.

5.2. Connecting Power

  1. Connect the power adapter (not included, use your robot vacuum's original adapter) to the charging base's power input port.
  2. Plug the power adapter into a wall outlet.
  3. Ensure the power indicator (if present on your robot vacuum or original base) illuminates, indicating the base is receiving power.
Side view of the charging base
Side view of the charging base, showing its profile.
Rear/bottom view of the charging base
Rear/bottom view of the charging base, showing potential cable routing or mounting points.

6. Operating Instructions

6.1. Automatic Charging

Your robot vacuum cleaner is designed to automatically return to the charging base when its battery is low or when a cleaning cycle is complete. Ensure the charging base is powered on and unobstructed for successful automatic docking.

6.2. Manual Charging

To manually charge your robot vacuum, carefully align the robot's charging contacts with those on the charging base and gently push the robot onto the base until it clicks into place. Ensure a secure connection.

6.3. Charging Indicators

Refer to your specific robot vacuum cleaner's manual for details on charging indicator lights. Typically, a solid light indicates charging, while a blinking light might indicate an error or standby mode.

7. Maintenance

7.1. Cleaning the Charging Contacts

Periodically inspect the metal charging contacts on both the base and the robot vacuum. If they appear dirty or corroded, gently wipe them with a clean, dry cloth. Do not use abrasive cleaners or liquids.

7.2. General Cleaning

Wipe the exterior of the charging base with a soft, dry cloth to remove dust and debris. Avoid using harsh chemicals or excessive moisture.

8. Troubleshooting

If you encounter issues with your charging base, refer to the table below for common problems and solutions.

ProblemPossible CauseSolution
Robot vacuum not dockingObstacles near base, incorrect placement, dirty contactsClear area around base, ensure base is flat, clean charging contacts.
Robot vacuum not chargingNo power to base, loose connection, dirty contacts, robot not properly dockedCheck power outlet, ensure power adapter is securely connected, clean charging contacts, re-dock robot.
Charging base moves easilyNot placed on a stable surfaceEnsure base is on a firm, flat surface. Some bases have rubber feet for stability.

9. User Tips

No specific user tips were available from customer reviews or Q&A for this product.

10. Warranty and Support

For warranty information or technical support, please contact the seller or the manufacturer of your robot vacuum cleaner. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.