FGHGF 820, 820S, 820T, 830, 830T

Contents

Robot Vacuum Cleaner Wheel Replacement Manual

For Proscenic 820, 820S, 820T, 830, 830T Series Robotic Vacuum Cleaners

1. Product Overview

This manual provides instructions for the replacement drive wheels designed for Proscenic 820, 820S, 820T, 830, and 830T series robotic vacuum cleaners. These wheels are essential spare parts to ensure the continued mobility and cleaning performance of your robot vacuum.

The wheels are available individually (Left or Right) or as a pair. An upgraded version of these wheels features improved tire performance for better traction and durability.

Upgraded Left and Right wheels for Proscenic robot vacuum cleaner
Figure 1: Upgraded Left and Right wheel assemblies, highlighting enhanced tire performance.

2. Compatibility

These replacement wheels are specifically compatible with the following Proscenic robot vacuum cleaner models:

  • Proscenic 820
  • Proscenic 820S
  • Proscenic 820T
  • Proscenic 830
  • Proscenic 830T

Note: Older versions of these wheels have been discontinued. All new replacements are the upgraded version.

3. Package Contents

Depending on your purchase, the package will contain one of the following:

  • One (1) Left Wheel Assembly
  • One (1) Right Wheel Assembly
  • One (1) Left Wheel Assembly and One (1) Right Wheel Assembly (Pair)
Left wheel assembly for Proscenic robot vacuum
Figure 2: Example of a Left wheel assembly.
Right wheel assembly for Proscenic robot vacuum
Figure 3: Example of a Right wheel assembly.

4. Installation/Setup

Replacing the drive wheels on your Proscenic robot vacuum cleaner typically involves a few steps. Always ensure the robot vacuum is powered off and disconnected from its charging base before beginning any maintenance or replacement procedures.

  1. Power Off: Turn off your robot vacuum cleaner and remove it from the charging station.
  2. Access Wheels: Carefully flip the robot vacuum upside down to access the bottom panel where the wheels are located.
  3. Remove Bottom Cover (if applicable): Some models may require removing a bottom cover or battery cover to access the wheel assemblies. Use a small screwdriver if necessary.
  4. Disconnect Old Wheel: Locate the wheel assembly you wish to replace. There will typically be screws holding it in place and a wire connector attaching it to the robot's main board. Carefully unscrew the retaining screws and gently disconnect the wire harness.
  5. Remove Old Wheel: Once unscrewed and disconnected, the old wheel assembly can be removed.
  6. Install New Wheel: Align the new wheel assembly into the designated slot. Reconnect the wire harness, ensuring it is securely seated.
  7. Secure New Wheel: Fasten the new wheel assembly with the retaining screws. Do not overtighten.
  8. Reassemble: If a bottom cover was removed, reattach it.
  9. Test: Place the robot vacuum back on its wheels and power it on. Perform a short test run to ensure the new wheel operates correctly and the robot moves smoothly.
Side view of a left wheel assembly
Figure 4: Side view of a left wheel assembly, showing its structure.
Bottom view of a left wheel assembly with motor and circuitry
Figure 5: Bottom view of a left wheel assembly, revealing the integrated motor and circuitry.

5. Maintenance

To prolong the life of your robot vacuum's wheels and maintain optimal performance:

  • Regular Cleaning: Periodically inspect the wheels and wheel wells for tangled hair, dust, or other debris. Use a small brush or tweezers to remove any obstructions.
  • Tire Inspection: Check the rubber tires for signs of wear, cracks, or damage. Worn tires can reduce traction and cleaning efficiency.
  • Axle Check: Ensure the wheels spin freely and are not stiff or grinding. If they are, further cleaning or replacement might be necessary.

6. Troubleshooting

If your robot vacuum is experiencing issues after wheel replacement or during normal operation, consider the following:

  • Robot Not Moving or Moving Unevenly:
    • Ensure the wheel assemblies are correctly installed and all screws are tightened.
    • Check that the wire harnesses are securely connected to the main board.
    • Verify that no debris is obstructing the wheel's movement.
  • Unusual Noise from Wheels:
    • Inspect for any foreign objects caught in the wheel mechanism.
    • Ensure the wheel is properly seated and not rubbing against the robot's chassis.

7. Specifications

Attribute Detail
Product Type Vacuum Cleaner Parts
Vacuum Part Type Wheels
Brand Name FGHGF
Compatible Models Proscenic 820, 820S, 820T, 830, 830T
Origin Mainland China
High-concerned chemical None
Package Length 18 cm
Package Width 15 cm
Package Height 12 cm
Package Weight 0.542 kg

8. User Tips

  • Before ordering, double-check your robot vacuum's model number to ensure full compatibility with these replacement wheels.
  • When installing, take photos of the original wheel's wiring and screw placement to aid in reassembly.
  • Keep the area around your robot vacuum's wheels clear of long hair, threads, and other debris to prevent premature wear and entanglement.

9. Support

If you encounter any issues not covered in this manual or require further assistance, please contact the seller or the manufacturer's customer support for your Proscenic robot vacuum cleaner.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.