ALIYIQI AWJ4-340 Digital Display Torque Wrench User Manual

Introduction

The ALIYIQI AWJ4-340 is an economical, high-precision digital display torque wrench designed for accurate torque measurement and application. This tool features a digital screen for clear data display and offers various operational capabilities including setting torque values, switching units, saving data, and calibration. Its user-friendly design aims to simplify operation for various applications requiring precise torque control.

Specifications

Package Contents

The following items are included in your product package:

• Digital Display Torque Wrench (AWJ4-340)
• Drying agent (1 bag)
• Key for battery box (1 set)
• User's manual (1 copy)
• Certificate + Warranty card (1 copy)
• Hard storage case

Note: AAA batteries are not included and must be purchased separately.

Setup

1. Battery Installation

1. Locate the battery compartment, typically at the base of the handle.
2. Use the provided key for the battery box to open the compartment.
3. Insert two (2) 1.5V AAA batteries, ensuring correct polarity (+/-).
4. Close the battery compartment securely.

2. Attaching Sockets/Accessories

1. Ensure the wrench is powered off.
2. Align the desired 1/2 inch drive socket or accessory with the square drive on the wrench head.
3. Push the socket firmly onto the drive until it clicks into place, indicating it is securely attached.
4. To remove, press the release button on the ratchet head and pull the socket off.

Operating Instructions

Familiarize yourself with the control panel and display before operation.

• M (Menu key): Used to access menu options and settings.
• C (Cancel key): Used to boot into real-time mode, or cancel an action.
• OK (Confirm key): Used to confirm selections.
• Up/Down Arrows: Used to adjust values or navigate menus.

1. Power On and Mode Selection

1. Press the 'C' key to power on the wrench and boot into real-time mode. The display will show the current torque being applied.
2. To switch to Peak Hold mode, click the 'OK' button. In Peak Hold mode, the display will show and hold the highest torque value reached during an application. Click 'OK' again to return to Real-Time mode.

2. Setting a Preset Torque Value

1. Click the 'M' key to enter the preset value setting.
2. Use the Up/Down arrow keys to adjust the desired torque value.
3. Press 'OK' to confirm the preset value.

3. Switching Units

1. Click the 'M' key three times to enter the unit switching menu.
2. Use the Up/Down arrow keys to cycle through the available units (N.m, kgf.cm, lbf.ft, lbf.in).
3. Press 'OK' to select the desired unit.

4. Applying Torque

1. Attach the appropriate socket to the wrench.
2. Place the socket onto the fastener.
3. Apply steady force to the wrench handle. The digital display will show the real-time torque.
4. When the applied torque reaches the preset value, the wrench will emit a buzzer sound and the LCD light will activate, indicating that the target torque has been achieved. Stop applying force immediately.

Maintenance

• Cleaning: Wipe the wrench with a clean, dry cloth after each use. Do not use abrasive cleaners or solvents.
• Moisture Protection: The wrench is made of stainless steel, but prolonged exposure to moisture, especially saltwater, can cause damage. If the wrench accidentally gets wet, dry it immediately with a dry towel.
• Storage: Store the torque wrench in its original hard case in a dry, clean environment away from direct sunlight and extreme temperatures.
• Battery Care: For long-term storage (more than one month), remove the AAA batteries to prevent leakage and damage to the electronic components.
• Calibration: Regular calibration is recommended to maintain accuracy, especially after heavy use or if accuracy is critical for your application. Refer to a professional calibration service.

Troubleshooting

If you encounter issues with your digital torque wrench, please refer to the following common troubleshooting steps:

• Display Not Working:
  • Check if the batteries are correctly installed and have sufficient charge. Replace if necessary.
  • Ensure the battery compartment is securely closed.
• Inaccurate Readings:
  • Verify that the correct unit is selected.
  • Ensure the wrench is used within its specified torque range (10-340 Nm).
  • Consider professional calibration if readings remain inconsistent or inaccurate.
• Alarm Not Sounding/LCD Light Not Activating:
  • Confirm that a preset torque value has been set.
  • Check battery level, as low power might affect alarm functions.
• Wrench Not Powering On:
  • Ensure batteries are new and correctly inserted.
  • Press the 'C' key firmly to power on.

User Tips

• Always select the appropriate socket size for the fastener to prevent damage to both the fastener and the wrench.
• Apply torque smoothly and steadily. Jerking or sudden movements can lead to inaccurate readings and potential damage.
• For critical applications, perform a test run on a non-critical fastener to ensure the wrench is functioning as expected.
• Keep the digital display clean and free from debris for optimal visibility.

Warranty and Support

This ALIYIQI product is covered by a manufacturer's warranty against defects in materials and workmanship. Please refer to the included Certificate + Warranty card for specific terms, conditions, and duration of the warranty. For technical support, service, or warranty claims, please contact your point of purchase or the official ALIYIQI customer service channels.