ETAxopowo FI-RE51S-HF

Contents

FI-RE51S-HF 51P 2ch 8-10bit LVDS Cable Instruction Manual

Model: FI-RE51S-HF

1. Product Overview

This document provides instructions for the ETAxopowo FI-RE51S-HF Flexible Flat Cable, a 51-pin, 2-channel 8-10bit LVDS cable designed for connecting displays to universal main circuit boards. It is compatible with various display panels from manufacturers such as Samsung, LG, and AU, and commonly used with main boards like v29, v59, v56, v53, and d3663lua.

Two FI-RE51S-HF LVDS cables, labeled 51P 2ch 8-10bit, 120Hz / LVDS / 55cm.
Figure 1: FI-RE51S-HF 51P 2ch 8-10bit LVDS Cable (120Hz / LVDS / 55cm)

2. Specifications

Attribute Detail
Model Number FI-RE51S-HF
Type Flexible Flat Cable (FFC)
Pin Configuration 51-pin, 0.5mm pitch
Channels 2-channel 8-10bit LVDS
Cable Length 550mm (55cm)
Refresh Rate Support Up to 120Hz
Compatibility Universal main circuit boards (e.g., v29, v59, v56, v53, d3663lua) and compatible LVDS screen interfaces (e.g., Samsung, LG, AU 40P DuPont).
Origin Mainland China
Certification None

3. Setup Instructions

Before connecting the LVDS cable, ensure that both your display panel and main circuit board are powered off and disconnected from any power source. Incorrect connection can cause damage to components.

  1. Verify Compatibility: Crucially, ensure that the LVDS interface type of your screen matches the pinout and configuration of this cable. This cable is designed for universal main circuit boards (e.g., v29, v59, v56, v53, d3663lua) and compatible display panels.
  2. Identify Cable Type: Determine if you have the 'Right Power in' or 'Left Power in' variant of the cable, as this affects the pin assignment. Refer to the images below for visual identification and detailed pinout diagrams.
  3. Connect to Main Board: Carefully align the 51-pin connector of the LVDS cable with the corresponding LVDS interface on your universal main circuit board. Ensure the connector is inserted straight and fully seated to avoid bending pins.
  4. Connect to Display Panel: Similarly, align and connect the other end of the LVDS cable to the LVDS interface on your display panel. Double-check the orientation to ensure correct pin alignment.
  5. Secure Connections: Once both ends are connected, gently tug on the cable near the connectors to ensure they are securely fastened and will not easily detach.

3.1 Pinout Diagrams

Refer to the following diagrams for detailed pin assignments for both 'Right Power in' and 'Left Power in' cable configurations. These diagrams are essential for verifying compatibility and troubleshooting connection issues.

FI-RE51S-HF LVDS cable variant with 'Right Power in' configuration.
Figure 2: 'Right Power in' Cable Variant
Pinout diagram for the 'Right Power in' FI-RE51S-HF LVDS cable, showing CN1 Module Side Connector (UJU IS050-C51B-C39-S or Equivalent) with 51 pins and their descriptions, including LVDS signals, ground, and power supply.
Figure 3: Pinout Diagram for 'Right Power in' (CN1 Module Side Connector)
FI-RE51S-HF LVDS cable variant with 'Left Power in' configuration.
Figure 4: 'Left Power in' Cable Variant
Pinout diagram for the 'Left Power in' FI-RE51S-HF LVDS cable, showing LCD connector (187059-51221 Manufactured by P-TWO) with 51 pins and their descriptions, including 12V power supply, ground, LVDS pixel data input, and reserved pins.
Figure 5: Pinout Diagram for 'Left Power in' (LCD Connector)

4. Operating Instructions

Once the FI-RE51S-HF LVDS cable is correctly installed between the main circuit board and the display panel, its operation is passive. The cable facilitates the transmission of video signals. Ensure all connections are secure before powering on your system.

  1. Power On: After ensuring all connections are firm and correct, connect the power supply to your main circuit board and display panel.
  2. Verify Display: Check if the display panel receives the video signal from the main board. If no image appears, power off immediately and re-check all connections and compatibility.

5. Maintenance

The FI-RE51S-HF LVDS cable requires minimal maintenance. Follow these guidelines to ensure its longevity and reliable performance:

  • Handle with Care: Flexible Flat Cables are delicate. Avoid sharp bends, excessive pulling, or twisting, which can damage the internal conductors.
  • Keep Clean: Keep the connectors free from dust, dirt, and moisture. Use a soft, dry cloth or compressed air to clean if necessary. Do not use liquid cleaners directly on the connectors.
  • Secure Environment: Ensure the cable is installed in an environment where it is not subject to physical stress, extreme temperatures, or high humidity.
  • Regular Inspection: Periodically inspect the cable and connectors for any signs of wear, fraying, or damage. Replace the cable if any damage is observed.

6. Troubleshooting

If you encounter issues after installing the FI-RE51S-HF LVDS cable, consider the following troubleshooting steps:

  • No Display/Garbled Image:
    • Check Compatibility: The most common issue is an incompatibility between the screen's LVDS interface and the cable's pinout. Carefully compare your screen's specifications with the cable's pinout diagrams (Figures 3 and 5).
    • Re-seat Connections: Power off the system and carefully disconnect and reconnect both ends of the LVDS cable. Ensure they are fully and correctly seated.
    • Verify Cable Orientation: Ensure the cable is not inserted upside down into either connector, as this can cause damage or prevent signal transmission.
    • Check Main Board Settings: Some universal main boards require specific firmware or jumper settings for different LVDS panel types. Consult your main board's manual.
  • Intermittent Display:
    • Inspect for Damage: Check the cable for any visible damage, kinks, or fraying. A damaged cable can lead to intermittent signal loss.
    • Secure Connectors: Ensure the connectors are not loose. Vibrations or slight movements can cause intermittent contact.

7. User Tips

  • Double-Check Pinouts: Always verify the pinout of your specific display panel against the cable's pinout diagrams (Figures 3 and 5) before making connections. LVDS interfaces can vary significantly.
  • Static Discharge: When handling the cable and connecting components, take precautions against electrostatic discharge (ESD) to prevent damage to sensitive electronics.
  • Cable Management: Route the cable carefully to avoid interference with other components and to prevent accidental damage.

8. Warranty and Support

For specific warranty information, return policies, or technical support regarding the ETAxopowo FI-RE51S-HF LVDS cable, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.