Steelmate 888E Two-Way LCD Car Alarm Keyless Entry Security System

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Steelmate 888E Two-Way LCD Car Alarm Keyless Entry Security System. This advanced system offers enhanced security and convenience features for your vehicle, including automatic locking/unlocking, anti-hijack protection, and remote control functionalities.

The Steelmate 888E system provides advanced security and convenience.

Main Features

The Steelmate 888E system is equipped with a range of features designed to protect your vehicle and offer ease of use:

• Automatic Locking/Unlocking: Doors automatically lock/unlock as the driver approaches or leaves the car (PKE - Passive Keyless Entry).
• Intelligent Anti-Hijack: Features an intelligent anti-hijack function with ID detection for enhanced security.
• Remote Control: Two-way LCD remote control displays the car's status and allows for various commands.
• Remote Trunk Release: Conveniently open your car's trunk with a simple press of a button on the remote.
• Car Locating: Helps you find your vehicle in a crowded parking lot.
• Dome Light Delay: Provides illuminated entry/exit.
• Alarm Arming/Disarming: Securely arm and disarm the system.
• Mute Arming: Arm the system silently.
• Shock Impact Detection: Triggers an alarm upon detecting significant impact.
• Door Open Detection: Alerts if a door is opened while armed.
• ACC ON Detection: Monitors ignition status.
• Battery Indicator: Remote control displays battery level.
• Signal Bar: Remote control indicates signal strength.
• Time Indicator: Remote control displays current time.
• Turn Signal Flashing: Visual confirmation for arming/disarming and alarm triggers.

Visual representation of the system's key functionalities.

Package Contents

Please check the package carefully to ensure all components are present:

• 1 x ECU (Electronic Control Unit)
• 1 x Siren
• 1 x Relay
• 1 x Antenna
• 1 x Cable Harness
• 2 x Transmitters (LCD Remote Controls)
• 1 x Shock Sensor
• 1 x PKE Antenna
• 1 x LED Indicator
• 1 x User Manual (this document)

Contents of the Steelmate 888E package.

Specifications

Setup and Installation

Installation of the Steelmate 888E system requires technical expertise and should ideally be performed by a qualified professional. Incorrect installation can lead to system malfunction or damage to your vehicle's electrical system.

General Guidelines:

• ECU Placement: Mount the ECU securely inside the vehicle, away from direct moisture and extreme temperatures.
• Siren Mounting: Install the siren in the engine bay, facing downwards to prevent water accumulation, and in a location that is difficult for intruders to access.
• Antenna Placement: Position the main antenna and PKE antenna for optimal signal reception, typically on the windshield or dashboard, away from metal obstructions.
• Shock Sensor: Mount the shock sensor on a rigid part of the vehicle's chassis to accurately detect impacts. Adjust sensitivity as needed after installation.
• Wiring: Connect all wires according to the provided wiring diagram, ensuring proper insulation and secure connections. Pay close attention to power, ground, ignition, door trigger, and turn signal connections.

Wiring Diagram:

Refer to the detailed wiring diagram below for specific connection points. This diagram is crucial for correct installation.

Consult this wiring diagram for all electrical connections during installation.

Operating Instructions

Remote Control Overview:

The two-way LCD remote control is your primary interface with the alarm system. Familiarize yourself with its buttons and display icons.

Key features and buttons of the LCD remote control.

• Arm Button (Lock Icon): Press once to arm the system and lock the doors.
• Disarm Button (Unlock Icon): Press once to disarm the system and unlock the doors.
• Mute Button (Speaker with X Icon): Press to arm the system silently or to temporarily silence an active alarm.
• Trunk Release Button (Trunk Icon): Press and hold to open the vehicle's trunk.
• Setting Button (SET): Used to access and adjust system settings on the remote.
• USB Charger: Port for recharging the remote control's internal battery.
• Display Symbols: Icons on the LCD screen indicate various statuses such as armed/disarmed, door open, shock detected, battery level, signal strength, and time.

Arming the System:

Press the Arm (Lock) button on the remote control. The doors will lock, and the turn signals will flash once to confirm the system is in alarm arming mode. The remote's LCD will display the armed status.

Arming the system by pressing the lock button on the remote.

Disarming the System:

Press the Disarm (Unlock) button on the remote control. The doors will unlock, and the system will disarm. The remote's LCD will update to show the disarmed status.

Passive Keyless Entry (PKE):

With PKE enabled, the system automatically locks the doors when you walk away from the vehicle with the remote control, and unlocks them as you approach. Ensure the remote is always with you when using this feature.

Remote Trunk Release:

To open the trunk, press and hold the Trunk Release button on your remote control. The trunk will pop open without needing to use a key.

Activating remote trunk release with the remote control.

Anti-Hijack Function:

The intelligent anti-hijack feature uses ID detection to prevent unauthorized vehicle use. If the system detects an attempt to hijack the vehicle, it will activate the alarm and immobilize the engine.

Alarm Trigger Response:

When the system is triggered by an event such as ignition, door opening, or shock impact, the siren will chirp for 30 seconds, turn signals will flash, and the engine will be immobilized to deter theft.

The system's response to a door trigger event.

Maintenance

• Remote Control Battery: The LCD remote control is rechargeable via a USB port. Recharge it when the battery indicator shows low power to ensure continuous functionality.
• System Check: Periodically test the alarm system's functions (arming, disarming, shock sensor) to ensure it is operating correctly.
• Cleaning: Keep the remote control and main unit clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
• Professional Inspection: Consider having the system professionally inspected annually to ensure all components are functioning optimally and wiring remains secure.

Troubleshooting

• System Not Responding: Check the remote control's battery level and recharge if necessary. Ensure you are within the system's operating range.
• False Alarms: Adjust the sensitivity of the shock sensor. Ensure all doors, hood, and trunk are fully closed when arming the system.
• PKE Not Working: Ensure the PKE antenna is correctly installed and not obstructed. Check the remote control's battery.
• Remote Display Issues: If the LCD remote display is blank or erratic, try recharging it. If the issue persists, the remote may need service or replacement.
• Siren Not Sounding: Check the siren's wiring connection to the ECU. Ensure the siren itself is not damaged.

User Tips

• Keep Remote Charged: Always keep your LCD remote control charged to ensure reliable operation of all features, especially PKE.
• Test Features Regularly: Periodically test the alarm and keyless entry functions to confirm everything is working as expected.
• Professional Installation: For optimal performance and to avoid potential issues, professional installation is highly recommended.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.