BAKON BK60/BK90

Contents

BAKON BK60/BK90 SMD Digital ESD Soldering Station User Manual

Model: BK60 / BK90 | Brand: BAKON

1. Introduction

The BAKON BK60/BK90 SMD Digital ESD Soldering Station is a professional-grade tool engineered for precise and efficient soldering tasks. It integrates advanced features such as intelligent temperature control, automatic standby and sleep modes, and a clear LED display to ensure optimal performance, energy efficiency, and user convenience. This manual provides essential information for the safe and effective setup, operation, maintenance, and troubleshooting of your soldering station.

2. Product Components

The BAKON BK60/BK90 Soldering Station package typically includes the following components:

  • 1 x Soldering Station (Main Unit)
  • 1 x Soldering Handle
  • 1 x Soldering Iron Stand (with cleaning sponge and brass clean ball)
  • 1 x Power Cable
  • 1 x User Manual (this document)
Components of the BAKON BK60/BK90 Soldering Station package including main unit, iron, stand, and cables.
Figure 2.1: Included components of the BAKON BK60/BK90 Soldering Station package.

3. Setup Instructions

  1. Unpacking: Carefully remove all components from the packaging. Inspect for any visible damage.
  2. Placement: Place the soldering station on a stable, heat-resistant, and ESD-safe workbench. Ensure adequate ventilation around the unit, particularly near the louver heat dissipation design at the rear.
  3. Connect Soldering Handle: Connect the soldering handle cable to the designated multi-pin port on the front panel of the soldering station. Ensure the connection is firm and secure.
  4. Assemble Soldering Iron Stand: Position the soldering iron stand in a convenient and safe location near the station. Ensure the cleaning sponge is moistened with distilled water (if applicable) and the brass clean ball is properly seated in its compartment.
  5. Power Connection: Connect the provided power cable to the power input socket located on the rear of the soldering station. Verify that the power switch (and fuse holder) is in the 'OFF' position before plugging the other end into a compatible AC 110V 60Hz or 220V power outlet, depending on your model.
Rear view of BAKON Soldering Station showing power input, switch/fuse, and louver heat dissipation design.
Figure 3.1: Rear view of the soldering station, highlighting the power input, switch/fuse, and heat dissipation louvers.

4. Operating Instructions

4.1 Power On/Off

  • To power on the unit, flip the power switch located at the rear of the main unit to the 'ON' position. The LED display will illuminate, showing the current and set temperatures.
  • To power off, flip the power switch to the 'OFF' position.

4.2 Temperature Control

The soldering station features a high-definition large-screen LED display and an intuitive visual operation panel for precise temperature adjustment.

  • Setting Temperature: Use the 'Plus' (↑) and 'Minus' (↓) keys on the front panel to adjust the desired working temperature. The set temperature will be prominently displayed.
  • Temperature Stability: The unit maintains excellent temperature stability of ±35.6°F (±2°C) for consistent soldering results.
  • Temperature Storage: The station includes a memory function that stores your last used temperature setting, allowing for quick recall upon power-on.
  • Software Calibration: The unit supports software calibration for maintaining accurate temperature readings over time. Refer to the detailed diagram for button functions and the full manual for calibration procedures.
Detailed view of BAKON Soldering Station controls and features, including LED display, set keys, and handle connection points.
Figure 4.1: Front panel controls and key features including LED display, set keys, and handle connection.

4.3 Smart Features

  • Auto Standby and Sleep: The station is equipped with automatic standby and sleep functions to conserve energy and extend the lifespan of the soldering tip. When the iron is placed in its stand and not in use for a user-defined period, it will automatically enter standby mode, reducing the tip temperature. After a longer period of inactivity, it will enter sleep mode, further cooling the tip.
  • Password Lock: For enhanced security and to prevent unauthorized temperature changes in professional environments, the unit includes a password lock feature. Consult the full manual for detailed instructions on setting and using the password lock.
  • Short Circuit Protection: Built-in short circuit protection safeguards the unit and connected components from potential electrical damage, ensuring safe operation.
  • Pulse Heating: The station utilizes advanced pulse heating technology to optimize heating efficiency, achieve rapid temperature recovery, and prolong the lifespan of the heating element.
Diagram illustrating intelligent precise temperature control with internal circuit board, versatility with various soldering tips, and the internal warming function of the station.
Figure 4.2: Overview of intelligent temperature control, tip versatility, and internal warming function.

5. Maintenance

Proper and regular maintenance is crucial for ensuring the longevity, optimal performance, and safety of your BAKON soldering station.

  • Tip Cleaning: Regularly clean the soldering iron tip using the provided moistened sponge or the brass clean ball. This process removes oxidation, old solder, and flux residue, which is essential for efficient heat transfer and good solder joints.
  • Tip Tinning: Always tin the tip with a small amount of fresh solder before and after each use, and during extended breaks. This prevents oxidation and helps maintain the tip's wettability.
  • Heating Element Replacement: The unit features a convenient plug-in ceramic heater design, which simplifies the replacement of the heating element if it becomes faulty. Always ensure the unit is powered off and completely cooled down before attempting any replacement.
  • General Cleaning: Keep the main unit and soldering iron handle clean and free from dust, debris, and solder splatter. Use a soft, dry cloth for cleaning. Avoid using abrasive cleaners, solvents, or liquids that could damage the electronics or display.
  • Fuse Replacement: If the unit fails to power on, first check the power cable and outlet. If the problem persists, inspect the fuse located near the power input on the rear of the unit. Replace a blown fuse only with one of the exact same type and rating to prevent damage.

6. Troubleshooting

If you encounter issues with your BAKON soldering station, refer to the following common troubleshooting steps. For problems not listed or if solutions do not resolve the issue, please contact customer support.

ProblemPossible CauseSolution
Station does not power onPower cable disconnected, power switch off, blown fuse, faulty power outlet.Verify power cable connection, ensure power switch is ON, check/replace fuse, test power outlet with another device.
Soldering iron not heating upSoldering handle not connected properly, faulty heating element, incorrect temperature setting.Ensure handle is securely connected to the station, check and adjust temperature setting, consider replacing heating element if necessary (refer to maintenance section).
Temperature unstable or inaccurateFaulty temperature sensor, need for calibration, environmental factors.Perform software calibration (refer to the full manual for the procedure). Ensure stable ambient temperature. If issue persists, contact support.
Tip not melting solder effectivelyOxidized or dirty tip, insufficient temperature, incorrect tip for the task, poor quality solder.Clean and re-tin the tip thoroughly, increase the set temperature, ensure an appropriate tip is used for the joint size, use fresh, good quality solder.

7. Specifications

FeatureDescription
ModelBAKON BK60 / BK90
Maximum Power60W (BK60) / 90W (BK90)
Operating Temperature Range362°F - 896°F (183°C - 480°C)
Temperature Stability±35.6°F (±2°C)
Operating VoltageAC 110V 60Hz or AC 220V (model dependent)
No-load Standby Power≤5W
Soldering Iron Tip Resistance to Ground<2Ω
Potential of Soldering Iron Tip to Ground<2mV
Correction MethodSoftware Calibration
DisplayHigh-definition Large-screen LED
Heating ElementPlug-in Ceramic Heater
Dimensions (Main Unit)Approx. 130mm (W) x 99mm (H) x 150mm (D)
CertificationsCE
Dimensions of the BAKON Soldering Station main unit, showing width, height, and depth measurements.
Figure 7.1: Main unit dimensions.

8. User Tips

To maximize your soldering experience, ensure safety, and prolong the life of your equipment, consider these practical tips:

  • Choose the Right Tip: Select a soldering tip appropriate for the size of the components and pads you are working on. A larger tip transfers heat more efficiently to larger joints, while a finer tip is better suited for delicate SMD work.
  • Maintain Tip Cleanliness: A clean, well-tinned tip is paramount for effective heat transfer and creating strong solder joints. Always clean your tip before and after each soldering session, and periodically during use.
  • Proper Temperature: Use the lowest effective temperature for your specific solder and components. Excessively high temperatures can damage sensitive components, degrade the soldering tip more quickly, and lead to cold solder joints due to rapid flux evaporation.
  • Good Ventilation: Always work in a well-ventilated area or use a dedicated fume extractor to avoid inhaling solder fumes, which can be harmful.
  • ESD Safety: While the station is ESD-safe, it is crucial to use other ESD precautions such as an ESD mat and a wrist strap when working with static-sensitive electronic components to prevent damage.

9. Warranty and Support

For detailed warranty information, technical support, or service inquiries regarding your BAKON BK60/BK90 Soldering Station, please contact your original point of purchase or the manufacturer directly. It is recommended to retain your purchase receipt or invoice as proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.