1. Introduction
The Estardyn XH-A901 NE5532 Tone Board is a versatile pre-amplifier module designed to enhance your audio experience by providing precise control over total volume, treble, middle (alto), and bass frequencies. Utilizing two NE5532 operational amplifiers, this board delivers clear audio signal processing, making it an ideal addition to various audio amplifier systems.

2. Setup and Installation
Proper connection is crucial for optimal performance. Please follow the instructions below carefully.
2.1 Wiring Diagram

Connections:
- Power Supply (DC12-24V Enter): Connect a DC power source within the 12V to 24V range to the designated power input terminals. Ensure correct polarity (+ and -).
- Audio Input (IN: R G L): Connect your audio source (e.g., MP3 player, smartphone, computer) to these terminals. 'R' is for the Right channel, 'G' is for Ground, and 'L' is for the Left channel.
- Audio Output (OUT: R G L): Connect these terminals to the input of your main amplifier board. 'R' is for the Right channel, 'G' is for Ground, and 'L' is for the Left channel.
- Amplifier Board Power Supply: Ensure your main amplifier board has its own appropriate power supply connected.
- Speakers: Connect your left and right speakers to your main amplifier board's output.
2.2 Physical Installation
- The board dimensions are 96mm x 39mm x 16mm.
- It features mounting holes with an aperture of 3mm.
- The installation hole distance is 89.3mm x 32.3mm.
- Mount the board securely in a suitable enclosure or chassis, ensuring it is protected from physical damage and short circuits.

3. Operating Instructions
Once properly connected and powered on, you can adjust the audio characteristics using the four potentiometers on the board:
- Total Volume: Controls the overall output level of the audio signal. Turn clockwise to increase volume, counter-clockwise to decrease.
- Treble: Adjusts the high-frequency response. Turn clockwise for brighter highs, counter-clockwise for softer highs.
- Middle (Alto): Adjusts the mid-range frequency response. This control affects the clarity and presence of vocals and many instruments.
- Bass: Adjusts the low-frequency response. Turn clockwise for deeper bass, counter-clockwise for less bass.
Adjust these controls to achieve your desired sound profile. Start with all controls at their center position and make small adjustments.
4. Maintenance
The XH-A901 Tone Board is designed for reliable operation with minimal maintenance.
- Cleaning: Keep the board free from dust and debris. Use a soft, dry brush or compressed air for cleaning. Do not use liquid cleaners.
- Environment: Operate the board in a dry environment, away from moisture, extreme temperatures, and direct sunlight.
- Handling: Avoid touching the electronic components directly, especially when powered, to prevent electrostatic discharge (ESD) damage.
5. Troubleshooting
- No Sound Output:
- Check if the power supply (DC12-24V) is correctly connected and providing power.
- Verify all audio input and output cables are securely connected to the correct terminals.
- Ensure the main amplifier board is powered on and functioning correctly.
- Check the 'Total Volume' knob is not set to minimum.
- Distorted or Unclear Sound:
- Ensure the input voltage is within the specified DC12-24V range. Incorrect voltage can cause distortion.
- Check the quality of your audio source.
- Reduce the input signal level if it is too strong, which can cause clipping.
- Excessive Noise or Hum:
- Ensure all ground connections are solid and properly connected.
- Use a high-quality, stable power supply. Switching power supplies can sometimes introduce noise; a linear power supply or adding a good L-C filter to the power input can help.
- Keep audio cables away from power cables to minimize interference.
6. Specifications
| Feature | Specification |
|---|---|
| Model | XH-A901 |
| Input Voltage | DC12-24V |
| Number of Channels | Two (Stereo) |
| Operational Amplifier Chip | 2 x NE5532 |
| Dimensions (L*W*H) | 96mm * 39mm * 16mm |
| Installation Aperture | 3mm |
| Installation Hole Distance | 89.3mm * 32.3mm |
| Package Type | DIP |
| Operating Temperature | -40°C to +85°C |
| Application | Audio pre-amplification, tone control for amplifier boards |
7. User Tips
- This tone board is excellent for adding treble, middle, and bass control to existing amplifier setups, such as connecting it to a speaker system.
- The pre-amplifier provides gain, meaning the output signal can be higher than the input signal, which can be useful for driving power amplifiers.
- If experiencing significant electrical noise, consider adding an L-C (inductor-capacitor) filter to the power input line for improved signal clarity.
- For advanced users, if the gain is too high (strong overrun), some users suggest modifying the first op-amp stage to reduce overall amplification. This should only be attempted by those with experience in electronics modification.
8. Warranty and Support
For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the seller or manufacturer directly through your purchase platform. Please provide your order details when seeking support.