CXG E110S

Contents

CXG E110S Electric Soldering Iron User Manual

Intelligent Sleep Function Digital Display Temperature Regulator Professional Rework Tool

1. Introduction

This manual provides comprehensive instructions for the safe and effective use of the CXG E-series Electric Soldering Iron (models E60S, E90S, E110S). This tool is designed for precise temperature control, rapid heating, and features an intelligent sleep function and LED digital display. It is suitable for disassembly, repair, and assembly of mobile phones, tablets, smart watches, and other electronic products, as well as for welding small electronic components.

Applicable Standards: Machinery Directive 2006/42/EC, EN ISO 12100, REACH (EC) 1907/2006, CLP (EC) 1272/2008, GPSR General Product Safety Regulation.

CXG E60S Soldering Iron with features: Precise temperature control, Rapid heat up, Auto sleep, LED display.

Figure 1: CXG E60S Soldering Iron highlighting key features.

2. Safety Warnings

DANGER WARNINGS

  1. The tool contains sharp components (bits, tweezers, welding tips); improper use may cause cuts and punctures. Welding tips are high-temperature during operation, which may cause burns.
  2. Always turn off the power and disconnect the battery cable before mobile phone repair. Confirm there are no exposed wires or static electricity in the work area before welding to avoid short circuits and fire.
  3. Keep away from children and pets; minors are prohibited from touching or using. Tools and consumables must be stored separately and locked.
  4. Always wear safety goggles and non-slip high-temperature resistant gloves during operation. Wear an additional protective mask during welding to prevent inhalation of flux fumes.
  5. Chemical consumables (glue, cleaner, flux) are strictly prohibited from being swallowed or coming into contact with eyes. Avoid contact with open flames. Ensure adequate ventilation during welding to prevent smoke accumulation.
  6. Immediately stop using the tool if it is damaged (e.g., deformed bits, cracked welding tips, damaged insulation layer of handles), slips, or overheats abnormally.
  7. Do not use repair pry bars or screwdrivers as crowbars or striking tools. Do not use welding tools to weld sealed containers or flammable and explosive materials.

Prohibited Actions

  • Violent machine prying, forcefully screwing, or over-pressing electronic components during welding.
  • Mobile phone disassembly or welding operation in the powered-on state.
  • Use by children, pregnant women, and inexperienced operators.
  • Operation in confined spaces, near flammable and explosive materials (alcohol, gasoline, etc.), or in environments with food.
  • Swallowing or applying any chemical consumables, and direct contact with high-temperature welding tips with hands.
  • Modifying the tool structure (e.g., lengthening the welding handle, replacing non-original bits/welding tips).
  • Welding components containing harmful metals such as lead and mercury, or over-temperature welding plastic parts with welding tools.

3. Product Features

  • Intelligent Temperature Control: Precise temperature regulation with a digital LED display, allowing adjustment from 80-500°C (176-932°F). Temperature error is less than ±5 degrees.
  • Rapid Heat-Up: Utilizes a high-quality internal heat type four-core ceramic heater for quick and stable temperature attainment.
  • Automatic Sleep/Shutdown: Built-in smart chip and sensor system. Can be set to sleep for 0-30 minutes. If sleep state is entered, the display shows 's-p', and the dormancy temperature is 80°C. If the soldering iron is picked up, the temperature quickly returns to the original setting. Automatic shutdown occurs after 120 minutes of inactivity in sleep mode for safety and energy saving.
  • Digital Display: Clear LED screen shows working temperature, Celsius/Fahrenheit conversion, and temperature complement settings.
  • Durable Construction: Features an anti-folding power cord sheath made of soft rubber for protection, an insulated handle for safety, and alloy electroplating soldering tips for fast heat conduction, anti-oxidation, and long life.
  • Multiple Power Options: Available in 60W (E60S), 90W (E90S), and 110W (E110S) models to suit various applications.
Digital display of the soldering iron showing sleep function, password management, Celsius/Fahrenheit conversion, temperature complement, and working temperature.

Figure 2: Digital display and smart functions.

Graph illustrating intelligent thermostatic control system with temperature compensation and stable temperature curve.

Figure 3: Intelligent Thermostatic Control System performance.

Diagram explaining automatic sleep/shutdown features, including dormancy temperature and safety benefits.

Figure 4: Automatic Sleep/Shutdown function details.

4. Setup and Pre-Use Inspection

4.1 Unpacking and Initial Check

  1. Carefully remove the soldering iron and any accessories from the packaging.
  2. Inspect the soldering iron for any visible damage.
  3. Ensure all components listed in your package are present.

4.2 Pre-Use Inspection

  1. Inspect all tools: Bits, pry bars, and tweezers should be free of cracks, deformation, and burrs. Welding tips should be free of oxidation and loosening. The insulation layer of handles should be intact.
  2. Confirm tool matches intended use: Ensure the repair screw model corresponds to the bit (e.g., cross, pentagon, hexagon), and the welding tool power is suitable for electronic components to avoid high-temperature damage.
  3. Inspect chemical consumables: Packaging should be intact without leakage or expiration (glue not hardened, flux not caked), and CLP hazard labels should be clearly visible.
Electric soldering iron three-piece set showing soldering iron, soldering iron stand, and cleaner. Note: The bracket needs to be purchased separately.

Figure 5: Soldering iron set components (stand and cleaner sold separately).

5. Operation Instructions

5.1 Mobile Phone Repair Operation

  1. Turn off the phone and take out the SIM card tray. Use the corresponding bit to vertically loosen the body screws (to avoid slipping).
  2. Use a pry tool to gently pry open the screen/back cover along the body gap (do not pry forcefully to prevent cable breakage).
  3. After disconnecting the battery cable, use tweezers to pick up small parts (such as screws, connectors), and avoid directly touching the motherboard with hands.
  4. When cleaning stains, gently wipe with alcohol wipes, avoiding sensitive parts such as the motherboard and cables. When gluing the screen, apply a small amount of glue evenly, align, and press to fix.

5.2 Small Electronic Welding Operation

  1. Confirm the welding area is well-ventilated and remove surrounding dust, oil, and flammable materials.
  2. Connect the welding tool to the power supply (if required) and preheat to the appropriate temperature (recommended 280-350°C, adjusted according to components).
  3. Apply a small amount of flux to the solder joint, touch the solder joint with the welding tip, and smoothly move the tool away after the solder melts. Do not touch the solder joint before cooling.
  4. After welding, turn off the tool power first, and store it after the welding tip is completely cooled.

5.3 Special Operation Instructions for Chemical Consumables

Mobile Phone Screen Glue (B7000/T7000)

  • For bonding mobile phone screens, frames, and bodies only; do not use for sealing electronic components or conductive parts.
  • The amount of glue applied should be "just covering the bonding surface"; excessive glue is easy to overflow and corrode components.
  • Avoid contact with skin and eyes; if accidentally contacted, rinse immediately with plenty of water; seek medical attention if it gets into eyes.
  • Keep ventilation during operation and avoid inhaling glue odor for a long time.

Electronic Cleaner/Alcohol Wipes (Isopropyl Alcohol / Anhydrous Ethanol)

  • For cleaning oil and dust on the surface of screens, body gaps, and welding solder joints; do not directly wipe live components.
  • Flammable item! Keep away from fire sources, high-temperature environments (such as the preheating area of welding tools), and static electricity; store in a sealed manner after use.
  • Do not mix with other chemical reagents to avoid producing toxic gases.

Welding Flux (Rosin-based, free of lead, cadmium, and other harmful heavy metals)

  • For welding small electronic components only; the dosage should be minimal (enough to wet the solder joint).
  • The smoke generated during welding must be discharged through ventilation to avoid inhalation; clean hands in time after operation.
  • Do not use for welding food contact utensils or medical equipment; prohibited from eating.

Video 1: Product demonstration and usage overview.

6. Maintenance and Storage

6.1 Post-Use Handling

  1. Clean the tools: Wipe the surface of the tools with a dry cloth to remove dust and glue residue. Clean the welding tip with a special cleaning sponge to remove solder residue and avoid oxidation.
  2. Store consumables: Tightly seal glue and flux, and store alcohol wipes in a sealed manner. Classify and place all tools in a storage box to avoid exposure of sharp parts.
  3. Clean the work area: Properly dispose of solder dross, used wipes, etc., and collect chemical waste separately; do not discard at will.

6.2 General Maintenance and Storage

  • Tool Maintenance: Keep dry to avoid moisture and rust. Apply a small amount of anti-rust oil to bits and welding tips (welding tips must be cooled before applying). Avoid contact of insulated handles with sharp objects to prevent damage.
  • Consumable Maintenance: Use within the shelf life (glue: 12-24 months, flux: 24 months). Discard expired consumables immediately.
  • Storage Requirements: Store tools and consumables separately in a dry, cool, and well-ventilated place with a temperature of 5-35°C and humidity ≤75%. Store the welding tool after it cools to room temperature to avoid high temperature damaging other items.
Tip for preventing oxidation: dip tin wire when heating at low temperature and after use.

Figure 6: Important tip for soldering iron tip maintenance.

7. Troubleshooting

This section addresses common issues you might encounter with your CXG Electric Soldering Iron.

  • Soldering Iron Not Heating Up:
    • Check if the power cord is securely plugged into a working outlet.
    • Ensure the power button on the soldering iron is pressed.
    • Verify the temperature setting is above the ambient temperature.
    • If the iron is in sleep mode ('s-p' displayed), pick it up to reactivate heating.
    • Inspect the heating core and tip for damage. Replace if necessary.
  • Temperature Fluctuation/Instability:
    • Ensure the soldering tip is properly seated and tightened.
    • Check for drafts or sudden temperature changes in the working environment.
    • Verify the temperature compensation setting if available.
    • If using a low-grade two-core heater, consider upgrading to a high-quality four-core heater for better stability.
  • Soldering Tip Oxidation:
    • Always tin the tip before first use and after each use, especially when heating at low temperatures (around 200°C).
    • Clean the tip regularly with a damp sponge or brass wool.
    • Ensure the tip is not left at high temperatures for extended periods when not in use. The sleep function helps prevent this.
  • Display Not Working:
    • Check power connection.
    • If the device has been dropped or physically damaged, internal connections might be loose. Contact support.

8. Specifications

Table of Product Technical Parameters for E60S, E90S, E110S models.

Figure 7: Product Technical Parameters.

Product Technical Parameters
ParameterE60SE90SE110S
Power60W90W110W
Temperature Range80-500°C (176-932°F)
Soldering Tips900M/C8 series
HeaterA1316A1319A13111
Functional ConfigurationWith sleep function
VoltageAC85-260V 50/60Hz
High Temperature Set of HeadGP4
Resistance of Soldering Tip to Ground<2Ω
Potential of Soldering Tip to Ground<2mV
Dimensions255*20mm (approx. total length 255mm, diameter 20mm, tip length 70mm)
Handle Line Length1.5m
Net Weight0.16kg

*This product has anti-static treatment. Specifications and appearance may be modified without prior notice.

Product size details diagram showing tip diameter 7mm, handle line length 1.5m, total length 255mm, diameter 20mm, tip length 70mm.

Figure 8: Product size details.

Diagram labeling product parts: power sheath, LED display, power key, insulated handle, temperature adjust key, nut, high temperature set of head, ventilation, stainless steel sleeve, alloy electroplating soldering tip.

Figure 9: Product part names.

9. User Tips

  • Understanding Sleep Mode: When the soldering iron enters sleep mode, the display will show 's-p'. The tip temperature will drop to 80°C. Simply pick up the iron, and it will rapidly return to your last set working temperature. This feature is designed for safety and to prolong tip life.
  • Tip Tinning for Longevity: To prevent oxidation and ensure a long lifespan for your soldering tip, always apply a small amount of solder (tin the tip) when the iron is heating up (especially at lower temperatures like 200°C) and immediately after you finish using it.
  • Optimal Temperature for Different Tasks: While the iron offers a wide temperature range, experiment to find the lowest effective temperature for your specific solder and components. This minimizes heat stress on components and reduces tip wear.
  • Ventilation is Key: Always work in a well-ventilated area, especially when using flux, to avoid inhaling fumes.

10. Disposal (EU WEEE Compliance)

  • Metal Tools (bits, tweezers, welding tips): Classify and recycle through metal recycling channels.
  • Plastic Components (pry bars, suction cups, handles): Dispose of according to local plastic recycling standards.
  • Chemical Consumables (remaining glue, flux, used alcohol wipes): Treat as hazardous waste and hand over to EU-certified hazardous waste disposal institutions.
  • Prohibited: Random disposal or incineration of tools or consumables; prohibited from pouring chemical consumables into sewers.

11. Warranty and Support

11.1 Warranty Period

  • Tools: Minimum 90 days (EU Mandatory) – Recommended 180 days.
  • Chemical Consumables: Minimum 30 days (EU Mandatory) – Covers packaging defects and expired products.

11.2 Warranty Coverage

Free repair or replacement for damages caused by manufacturing defects. Human-induced damages (such as violent use, misoperation) are not covered by the warranty.

11.3 EU Exclusive Support

  • Local Service Center Address: France (EEA Country).
  • Language Support: English, German, French, Spanish, Italian (24-Hour Emergency Response).

11.4 Contact Information

  • Customer Service Email: 563528964@qq.com
  • EU Authorized Representative Consultation: MJCM SARL (Tel: 767213611)
  • Manufacturer Contact: shenzhen jinliyang Technology Co., Ltd

A user manual PDF is available for download: View User Manual (PDF)

© 2024 CXG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.