1. Product Overview
The CXG Intelligent Sleep Soldering Iron series (E60S, E90S, E110S) offers precise temperature control, rapid heat-up, and an auto-sleep function for enhanced safety and energy saving. Featuring an LED digital display, these tools are designed for professional rework and repair tasks.
- Precise Temperature Control: Maintain stable temperatures for delicate work.
- Rapid Heat Up: Quickly reaches desired operating temperature.
- Auto Sleep Function: Automatically enters sleep mode after a set period (0-30 minutes) of inactivity, reducing power consumption and preventing tip oxidation.
- LED Display: Clear digital display for temperature, Celsius/Fahrenheit conversion, and other settings.
- Smart Chip & Sensor: Ensures stable performance and intelligent power management.
- Anti-folding Power Cord Sheath: Made of soft rubber for durability and protection against breakage.
- High Quality Heater: Utilizes a four-core ceramic heater for constant temperature and rapid heating.
2. Safety Warnings
DANGER WARNINGS
- The tool contains sharp components (bits, tweezers, welding tips); improper use may cause cuts and punctures; welding tips are high-temperature during operation, which may cause burns.
- Must turn off the power and disconnect the battery cable before mobile phone repair; confirm there are no exposed wires or static electricity in the work area before welding to avoid short circuit and fire.
- Keep away from children and pets; minors are prohibited from touching or using; tools and consumables must be stored separately and locked.
- Must wear safety goggles and non-slip high-temperature resistant gloves during operation; wear an additional protective mask during welding (to prevent inhalation of flux fumes).
- Chemical consumables (glue, cleaner, flux) are strictly prohibited from being swallowed or coming into contact with eyes, and avoid contact with open flames; keep ventilation during welding to prevent smoke accumulation.
- Immediately stop using if the tool is damaged (such as deformed bits, cracked welding tips, damaged insulation layer of handles), slips or overheats abnormally.
- Do not use repair pry bars or screwdrivers as crowbars or striking tools; do not use welding tools to weld sealed containers or flammable and explosive materials.
EU Exclusive Mandatory Warnings
- DE: Vorsicht! Scharfe Teile und heiße Schweißköpfe! Nicht für Kinder geeignet. Nur für elektronische Reparaturen und Kleinschweißarbeiten!
- FR: Attention! Pièces pointues et têtes de soudure chaudes! Tenir hors de portée des enfants. Utilisation exclusive pour réparations électroniques et petites soudures!
- IT: Attenzione! Parti appuntite e teste di saldatura calde! Tenere lontano dai bambini. Uso esclusivo per riparazioni elettroniche e piccole saldature!
- ES: ¡Precaución! Piezas afiladas y puntas de soldadura calientes! Mantener fuera del alcance de los niños. Uso exclusivo para reparaciones electrónicas y soldaduras pequeñas!
- EU Universal:
- Ce produit contient des pièces pointues et des éléments de soudure chauds, risque de coupure et de brûlure.
- Utilisation uniquement pour la réparation électronique et la soudure de composants électroniques petits.
- Respecter les normes CE, REACH et CLP.
3. Setup
3.1 Pre-Use Inspection
- Inspect all tools: Bits, pry bars and tweezers should be free of cracks, deformation and burrs; welding tips should be free of oxidation and loosening; insulation layer of handles should be intact.
- Confirm tool matches intended use: The repair screw model corresponds to the bit (cross / 五角/hexagon, etc.), and the welding tool power is suitable for electronic components (to avoid high-temperature damage to components).
- Inspect chemical consumables: Packaging should be intact without leakage or expiration (glue not hardened, flux not caked), and CLP hazard labels should be clearly visible.
3.2 Initial Setup
- Connect the soldering iron to a compatible power outlet (AC85-260V 50/60Hz).
- Ensure the work area is well-ventilated and free from flammable materials.
- Place the soldering iron in a stable, heat-resistant stand when not in use. Note: The soldering iron stand and cleaner are typically purchased separately.
4. Operation
4.1 Mobile Phone Repair Operation
- Turn off the phone and take out the SIM card tray.
- Use the corresponding bit to vertically loosen the body screws (to avoid slipping).
- Use a pry tool to gently pry open the screen/back cover along the body gap (do not pry forcefully to prevent cable breakage).
- After disconnecting the battery cable, use tweezers to pick up small parts (such as screws, connectors), and avoid directly touching the motherboard with hands.
- When cleaning stains, gently wipe with alcohol wipes, avoiding sensitive parts such as the motherboard and cables; when gluing the screen, apply a small amount of glue evenly, align and press to fix.
4.2 Small Electronic Welding Operation
- Confirm the welding area is well-ventilated, and remove surrounding dust, oil and flammable materials.
- Connect the welding tool to the power supply (if required), and preheat to the appropriate temperature (recommended 280-350℃, adjusted according to components).
- Apply a small amount of flux to the solder joint, touch the solder joint with the welding tip, and smoothly move the tool away after the solder melts; do not touch the solder joint before cooling.
- After welding, turn off the tool power first, and store it after the welding tip is completely cooled.
4.3 Temperature Adjustment and Sleep Function
- Use the temperature adjust keys (usually '+' and '-') to set the desired working temperature. The LED display will show the current temperature.
- The soldering iron features a smart chip and sensor system that allows you to set the sleep duration from 0 to 30 minutes. This saves energy and enhances safety.
- When the sleep state is entered, the display screen will show 'S-P'. The dormancy temperature is 80 degrees Celsius. When the soldering iron is picked up again, the temperature quickly rises to the original setting.
- You can convert between Celsius (°C) and Fahrenheit (°F) using the dedicated button on the handle.
5. Maintenance
5.1 Post-Use Handling
- Clean the tools: Wipe the surface of the tools with a dry cloth to remove dust and glue residue; clean the welding tip with a special cleaning sponge to remove solder residue and avoid oxidation.
- Store consumables: Tightly seal glue and flux, and store alcohol wipes in a sealed manner; classify and place all tools in a storage box to avoid exposure of sharp parts.
- Clean the work area: Properly dispose of solder dross, used wipes, etc., and collect chemical waste separately; do not discard at will.
5.2 Tool and Consumable Maintenance
- Tool Maintenance: Keep dry to avoid moisture and rust; apply a small amount of anti-rust oil to bits and welding tips (welding tips must be cooled before applying); avoid contact of insulated handles with sharp objects to prevent damage.
- Consumable Maintenance: Use within the shelf life (the shelf life of glue is usually 12-24 months, and that of flux is 24 months); discard expired consumables immediately.
5.3 Storage Requirements
- Store tools and consumables separately in a dry, cool and well-ventilated place with temperature 5-35°C and humidity ≤75%.
- Store the welding tool after it cools to room temperature to avoid high temperature damaging other items.
6. Troubleshooting
Temperature Spikes on Startup
Issue: Upon turning on the soldering iron, the temperature display may initially show a high temperature or spike to maximum before settling. After this initial spike, temperature regulation becomes possible.
Resolution: This behavior is normal for soldering irons with rapid heat-up capabilities. The device quickly reaches a high temperature to minimize waiting time. Once the target temperature is reached, the intelligent control system will regulate it to your set value. Allow a few moments for the temperature to stabilize after the initial power-on and adjustment.
7. Specifications
| Feature | Detail |
|---|---|
| Brand Name | BES / CXG |
| Model Number | E60S, E90S, E110S |
| Power | 60W (E60S), 90W (E90S), 110W (E110S) |
| Input Voltage | AC85-260V 50/60Hz |
| Output Temperature | 80-500℃ (176-932℉) |
| Temperature Stability | ±5℃ |
| Dimensions | 255*20mm (Handle line length: 1.5m, Tip diameter: 7mm) |
| Weight | 0.16kg |
| Ground Impedance | <2Ω |
| Electric Potential of Iron Head to Ground | <2mV |
| Certification | CE, FCC, RoHS |
| Is Smart Device | No |
| High-concerned chemical | None |
| Origin | Mainland China |
| Welding Tip Series | 900M/C8 series |
| Heating Core | A1316 (E60S), A1319 (E90S), A13111 (E110S) |
| High Temperature Sleeve | GP4 |
| Functional Configuration | With hibernation function, Anti-static treatment |
8. User Tips
- Preventing Tip Oxidation: When using the electric soldering iron, especially at lower temperatures (e.g., 200°C), always dip the tin wire onto the tip to prevent oxidation. After use, ensure you dip the tin onto the tip to protect it before storage.
- Temperature Stabilization: After powering on, the soldering iron heats up rapidly. Allow a few moments for the temperature to stabilize at your set point before beginning work.
- Tip Selection: The 900M series offers a variety of tips for different applications. Choose the appropriate tip for your specific soldering task to ensure optimal performance and longevity.
9. Warranty and Support
9.1 Warranty Period
- Tools: Minimum 90 days (EU Mandatory) – Recommended 180 days.
- Chemical Consumables: Minimum 30 days (EU Mandatory) – Covers packaging defects and expired products.
9.2 Warranty Coverage
Free repair or replacement for damages caused by manufacturing defects. Human-induced damages (such as violent use, misoperation) are not covered by the warranty.
9.3 EU Exclusive Support
- Local Service Center Address: France (EEA Country)
- Language Support: English, German, French, Spanish, Italian (24-Hour Emergency Response)
- Refund Policy: Complies with EU Consumer Rights Directive – Supports 14-day free return without reason (products must be unopened and unused).
9.4 Contact Information
- AliExpress Store Link: www.aliexpress.com/store/4504021
- Customer Service Email: 563528964@qq.com
- EU Authorized Representative Consultation: MJCM SARL (Tel: 767213611)
- Manufacturer Contact: shenzhen jinliyang Technology Co., Ltd
10. Disposal (EU WEEE Compliance)
- Metal Tools (bits, tweezers, welding tips): Classify and recycle through metal recycling channels.
- Plastic Components (pry bars, suction cups, handles): Dispose of according to local plastic recycling standards.
- Chemical Consumables (remaining glue, flux, used alcohol wipes): Treat as hazardous waste and hand over to EU-certified hazardous waste disposal institutions.
- Prohibited: Random disposal or incineration of tools or consumables; prohibited from pouring chemical consumables into sewers.
11. Additional Resources
For a detailed user manual in PDF format, please refer to the official document: