FIMI MINI 3

Contents

FIMI MINI 3 User Manual

Version V1.2, 2025.7

1. Product Introduction

The FIMI MINI 3 is a highly integrated foldable mini quadcopter featuring long endurance, strong wind resistance, and a lightweight body weighing 250g. It includes a high-precision three-axis mechanical stabilization gimbal and a high-speed image processing chip for stable and smooth 4K 60fps footage. It offers high-definition real-time video transmission up to 9km, enabling long-distance flights without worry. Paired with a remote controller, it's easy to carry and operate. The app interface is simple and user-friendly, with added AI Super Night Video and 8K time-lapse recording functions, simplifying operation for a more enjoyable user experience.

1.1. Product and Accessories

The standard product package includes the following items:

  • Drone with camera
  • Remote controller
  • Intelligent Flight Battery
  • Propellers (8 pieces)
  • Screwdriver
  • Gimbal Cover
  • Charging Cable
  • USB Cable
  • Instruction Manuals (2 pieces)
  • Screws (4 pieces)
FIMI MINI 3 drone and accessories including remote control, battery, propellers, charging cable, gimbal cover, and USB cable.

Figure 1: FIMI MINI 3 and included accessories.

1.2. Function Overview

Gimbal Camera Performance

The camera features a 1/2-inch Sony CMOS image sensor and a high-precision three-axis gimbal for stable 4K 60fps video and 48-megapixel photos. It supports both landscape and portrait shooting modes. Key features include AI Super Night Scene for enhanced low-light performance (4x signal-to-noise ratio improvement) and 8K timelapse photography (up to 8000x6000 pixels).

Transmission Distance

The FIMI MINI 3 uses SoLink HD digital transmission technology, supporting up to 9 kilometers communication distance and 720p 30fps real-time video transmission in interference-free and unobstructed environments. It supports dual-band switching (2.4 GHz and 5.8 GHz) and minimizes video transmission latency to 120 milliseconds.

Smart Flight Functions

New SoC technology enables recognition and tracking of up to 30 types of targets (people, vehicles, boats, animals). Intelligent flight functions include Route Flight, Follow 3.0, Waypoint Flight, and Spiral Flight.

2. Setup

2.1. Prepare The Drone

The drone is shipped in a folded state. Follow these steps to prepare it for flight:

  1. Remove the propeller tie: Gently remove any ties securing the propellers.
  2. Remove the gimbal cover: The gimbal cover protects the camera during transport. Remove it before powering on.
  3. Unfold the drone: First, unfold the front arms, then unfold the rear arms, and extend all propellers.
Diagram showing how to unfold the FIMI MINI 3 drone arms.

Figure 2: Unfolding the drone arms.

Important Note: Before powering on, ensure the gimbal protector is removed and arms are unfolded to avoid affecting the drone's self-check. Reinstall the gimbal protector when not in use.

2.2. Prepare The Remote Controller

  1. Install Joysticks: Remove the joysticks from their storage slots and screw them clockwise into the remote controller.
  2. Extend Antennas: Pull up the antennas to their extended position.
  3. Mobile Device Installation:
    1. Connect the data cable to your phone's interface.
    2. Insert the data cable into the remote controller interface.
    3. Pull the remote controller apart to secure your mobile device.
Diagram showing joystick installation and mobile device setup on the remote controller.

Figure 3: Remote controller setup with joysticks and mobile device.

2.3. Installation and Removal

Propeller Installation

The drone motors use clockwise (CW) and counterclockwise (CCW) propellers. Ensure marked propellers are installed on marked arms and unmarked propellers on unmarked arms. Replace propellers and screws together when changing them.

Diagram showing propeller installation with marked and unmarked propellers.

Figure 4: Propeller installation diagram.

Important Notes: Always use official screws. Replace both propeller and screws if damaged. Avoid contact with spinning propellers. Check propellers for damage if flight instability occurs. Ensure no foreign objects are in motors.

Intelligent Flight Battery Installation

Push the battery firmly into the drone until a 'click' sound is heard. To remove, press the bottom buckle and pull out the battery.

Diagram showing the intelligent flight battery being inserted into the drone.

Figure 5: Intelligent Flight Battery installation.

Important Note: Improper battery installation can pose a flight safety risk.

Insert Micro SD Card

Pull out the battery before installing the Micro SD card. Insert the SD card into the slot. To remove, press the SD card to pop it out.

Equip and Remove Gimbal Protector

Attach and detach the gimbal protector as shown in the diagrams.

Diagram showing how to equip and remove the gimbal protector.

Figure 6: Gimbal protector installation and removal.

3. Operating Instructions

3.1. Drone Power On/Off

To power on/off the drone, briefly press the power button, then long press for 2 seconds. Briefly press to check the battery level.

3.2. Flight Mode

The drone supports various flight modes, switchable via the FIMI Navi Mini App:

  • GPS Mode (Standard): Uses GPS for precise hovering and intelligent flight features. Offers Sport Mode (max 18 m/s speed) and Beginner Mode (restricted speed, distance, altitude).
  • VPU Mode (Optical Flow): Achieves precise hovering using the optical flow module. Intelligent flight functions are not supported. Max speed 10 m/s. Suitable for indoor flight or weak GPS signals with clear ground textures.
  • ATTI Mode (Attitude): Relies on internal sensors when GPS or optical flow signals are weak. Drone may drift horizontally. Max speed 18 m/s. Land as soon as possible in a safe location.
  • Cine Mode: Limits maximum flight speed, ascent, and descent speeds for stable shooting.
  • Normal Mode: Most commonly used mode. Max horizontal speed 16 m/s.
  • Sport Mode: Increases horizontal flight speed to 18 m/s for a stronger flying experience.

Important Note: Sport mode is disabled above 2400 meters. In Sport mode, the drone's attitude control sensitivity is increased, and braking distance is longer. Videos may exhibit slight shakiness.

3.3. Drone Light Status

The drone's status lights indicate its current state:

Light StatusDrone Status
Yellow light fading in and outSelf-checking
Red light onSelf-check fails (on ground) / Attitude Mode (flying)
Red and yellow lights flash alternatelyCalibrate the compass
Green light flashing twiceReady to fly / In flight
Red light flashing twiceLow battery alerts
Red light flashing quicklyVery low battery alerts, land as soon as possible
Red and green lights flash alternatelyUpdating firmware
All lights offDrone is pairing to the RC

3.4. Intelligent Flight Battery Usage

Check Battery Level

With the battery inserted, briefly press the drone's power button to check the current battery level via the LED indicators.

Low-Temperature Usage Precautions

  • Ensure battery is fully charged in low temperatures (-5°C to 10°C).
  • Preheat battery to above 10°C (ideally 20°C) before flight in cold conditions.
  • Output power is limited in low temperatures, reducing wind resistance.

Charging

Connect the charging cable to the battery charging port. The battery indicator light will flash during charging and turn off when fully charged. Charging times vary:

  • 5V/2A: approx. 2.5 hours
  • 9V/2A: approx. 1.5 hours
  • 9V/3A: approx. 1 hour

Important Note: Use a USB charger with QC2.0 or higher protocol for faster charging. PD fast charging is not supported. Permissible charging temperature is 5°C to 40°C.

3.5. Gimbal Camera Working Mode

The gimbal can operate in two modes:

  • Follow Mode: The angle between the gimbal's orientation and the aircraft's front remains constant.
  • FPV Mode: The gimbal synchronizes with the aircraft's movement, providing a first-person flying experience. Select FPV mode in the FIMI Navi Mini App (Image Transmission -> Intelligent Flight -> Flight Mode -> Fixed-Wing).

Important Notes: Ensure no objects are on the gimbal before takeoff. Handle the gimbal carefully as it contains precision components. Remove the gimbal protector before powering on and reinstall for storage.

3.6. Remote Controller Operation and Usage

Power On/Off

Briefly press, then long press for 2 seconds to turn the remote controller on or off. Briefly press to check battery level.

Controller Functions

The remote controller features joysticks for flight control, an auto-return button, a TYPE-C port for charging/connecting mobile devices, and battery level lights.

Sticks Control

Different control modes (Mode 1, Mode 2, Mode 3) define joystick functions for ascending, descending, turning, and moving forward/backward/sideways. The default setting is for American hands.

Button Shortcuts

  • Photo Button: Press once to take a photo (two short beeps).
  • Video Button: Press once to start/stop recording (four short beeps to stop).
  • Dial: Adjusts the gimbal's pitch angle.

3.7. Remote Controller Indicator Lights

Four white LED lights indicate battery level and status:

Remote LightsRemote Status
Short press power buttonCheck battery level
Fade in and outNot connected to drone
Flash in turnPairing or updating firmware
Light keeps onConnection normal

Remote Controller Battery Level Display

LEDs indicate battery level: 75%-100%, 50%-74%, 25%-49%, 10%-24%. The remote controller beeps when battery level is less than 10%.

Charging

Connect the remote controller to a power adapter. Battery level lights flash during charging and turn off when fully charged. Takes about 2.5 hours to fully charge when powered off.

3.8. Remote Controller Communication Range

Adjust the orientation and distance between the remote controller and aircraft, and antenna position, to maintain optimal communication range. The antenna forms a 180° or 270° angle with the back of the remote controller, and the antenna plane directly facing the aircraft, optimizes signal quality.

Important Note: Avoid using other communication devices on the same frequency band to prevent interference.

3.9. Remote Controller Pairing

The remote controller and drone are factory-paired. If new equipment is used, re-pairing is required:

  1. Turn on the drone and remote controller.
  2. Wait 20 seconds, then long press the controller's power button until a beep sounds and the light flashes.
  3. Long press the drone's power button until the tail light turns off.
  4. Pairing succeeds when the RC power button turns white and the drone's tail light stays on.

Important Note: Ensure drone and RC are within 0.5m and battery level is over 30% during pairing.

3.10. FIMI Navi Mini App

The FIMI Navi Mini App provides flight data recording, flight logs, and allows users to view and manage their flight data. It also offers various functions and settings for the drone.

Main Page Display

Swipe left or right to select the desired drone model. If the remote controller is connected, it will automatically switch to the corresponding model.

Main Page Function Introduction

The app allows access to settings, flight data, region display, language switch, and app version check. It also provides a New User Guide.

Gesture Operations

In the live view interface, swipe left for full-screen mode and swipe right to exit.

Image Interface

The image interface displays flight data (height, distance, speeds, battery), GNSS signal strength, mapping signal quality, and battery power. It also allows access to system settings.

System Settings

Includes drone, camera, remote controller, gimbal, and battery information settings. Allows resetting parameters and viewing flight logs, firmware version, etc.

Toggles The Current Mode Of The Camera

Photo modes include single shot and time-lapse. Video modes include Normal Video, Super Night View, and Time-Lapse Recording. One-click clips include skydiving, self-timer flight, fixed-point loop, fixed-point spiral, and tail-flip flight. Panorama modes include Landscape, Vertical, and Wide Angle.

Shooting Buttons

Dedicated buttons for starting/stopping video recording, shooting photos, and one-tap video.

Media Library

Access, download, and view videos and photos stored on the drone's Micro SD card.

Smart Flight

Includes Pointing Flight, Route Flight, Follow 3.0, Point Wrap Flight, Spiral Flight. Flight modes include Aerial Mode, Tripod, Heading Lock, Fixed Wing, SAR.

Flight Gear Switching Shortcuts

Display and switch between smooth, normal, and sport flight gears.

Camera Parameter Mode Shortcuts

Switch between manual/automatic camera parameter modes.

SD Card Status Bar

Displays remaining and total capacity of the SD card. Click to enter SD card settings.

Gimbal And Image Parameter

Displays video resolution/frame rate and image size. Allows setting video/photo mode, resolution, image size, white balance, style, shutter value, ISO value, EV value, and fast zoom.

Gimbal Pitch Angle

Displays current pitch angle. Press and hold for 2 seconds to bring the gimbal down vertically, double click to center.

AI Super Night View

Shortcut switch for AI Super Night View in video mode.

Follow 3.0

After GNSS mode takeoff, click to enter Follow 3.0 mode.

Zoom Map / Attitude Sphere

Real-time display of vehicle position. Click to switch mapping interface/attitude sphere/thumbnail map/full-screen map display.

Map Interface

Displays aircraft coordinates, current time, and supports map transmission screen indentation and screenshot. Allows switching satellite maps.

Shortcuts

Tap for auto takeoff, auto land, and return to home.

Message Status Bar

Displays alerts for restricted flight zones, environmental changes, temperature, sensor calibration, and more.

3.11. Safety Protection

Auto-return

The drone features an automatic return function triggered by user initiation, low battery, or lost connection. It operates in GPS mode. The drone will ascend to a safe altitude (default 30m) and return to the takeoff point.

Diagram illustrating auto-return flight paths based on distance and altitude.

Figure 7: Auto-return flight paths.

Low-power Protection

The app prompts users to return when battery power is sufficient for return flight. At 30% battery, it suggests landing. At 10%, the aircraft lands automatically. Tap the return button to stop landing.

Hovering On The Edge of No-fly-zone

The drone automatically hovers at the edge of designated no-fly zones (e.g., airports). Users can fly the drone from the edge but not into the no-fly zone.

Height And Distance Limitations

Maximum altitude and distance can be set in the FIMI Navi Mini App.

Flight Environment Requirements

  • Not suitable for persons under 16 years of age.
  • Maintain distance from people, animals, trees, vehicles, and buildings.
  • Avoid dangerous environments (airports, railroads, highways, high-rise buildings, utility poles).
  • Stay away from areas with complex electromagnetic signals.
  • Do not fly in bad weather (windy, rainy, snowy, foggy).
  • Choose locations with good GPS signal and open environments.
  • Recommended for daytime flight only.
  • This product does not support the installation of protective devices or overweight loads.

Pre-flight Inspection

  • Ensure drone and remote control batteries are charged.
  • Verify propellers are properly installed and undamaged.
  • Gimbal protector removed, camera lens cleaned.
  • SD card inserted.
  • Front and rear arms fully deployed.
  • Camera and gimbal working properly.
  • FIMI Navi Mini App connected and working properly.

Novice Mode

Defaults to Novice Mode for first-time users. Limits flying distance and altitude to 0-100m and speed to photography gear. Recommended for beginners.

3.12. Basic Flight

Confirm the Direction of the Drone

The gimbal camera position indicates the nose direction. The color of the status light on the tail also indicates direction.

Safety Tip: Keep the tail facing the operator to avoid misjudging direction.

Take Off/Landing

To start propellers, hold both sticks to the bottom inner position for over 3 seconds. Release sticks, then push the left stick upward to take off. To land, slowly move the left stick downward. Hold the left stick down for over 5 seconds after landing to stop motors.

Diagram showing joystick movements for propeller start, takeoff, and landing.

Figure 8: Joystick controls for takeoff and landing.

Important Note: Take off from a smooth, fixed plane. Do not hand-hold or palm takeoff. Not waterproof; do not land on water or inclined surfaces.

Basic Flight Operations

Use joysticks for up/down, turning, forward/backward, and sideways flight. Releasing joysticks will make the drone hover automatically.

Stop Propellers In An Emergency

If motors cannot turn off, toggle the left stick to the bottom inner maximum range and press the Auto-return-to-home button for 5 seconds simultaneously.

Important Note: Do not perform this operation during normal flight to avoid stopping motors in the air.

Automatic Take-off/Landing/Return

In the FIMI Navi Mini App, click the automatic takeoff button. The drone will automatically take off and hover at 2.5 meters (GPS mode) or 1.2 meters (VPU mode). For automatic landing, click the button, and the drone will descend vertically. For automatic return, use the auto return button in the app or long press the return button on the remote control.

3.13. Intelligent Flight

Follow 3.0

In GNSS mode, select Follow Flight in the Smart Flight menu. Choose Normal, Parallel, or Locked Follow. The drone will follow the selected target.

Screenshot of FIMI Navi Mini App showing Follow 3.0 mode options.

Figure 9: Follow 3.0 mode in FIMI Navi Mini App.

Orbit A Point Flight

Select orbit a point flight in the app, set the center point and radius. The drone will fly around the center point. If a POI is set, the drone will lock and shoot the POI.

Spiral Flight

Select spiral mode in the app, set center point and radius. The drone will hover up and shoot video, showing a strong sense of space.

Tap-fly

Select Tap-fly in the app. Tap the map to choose a destination, and the drone will fly there at a default speed. If a point of interest is set, the camera will be locked at the POI.

Waypoint

Choose waypoint or drawing route on the map. The drone flies along the waypoint route at a default speed. If a point of interest is set, the camera will be locked at the POI.

Precise Landing

During Return to Home, the optical flow sensor identifies the landing pad for precise landing.

Intelligent Flight Mode

Includes Aerial Mode (softer control, stable shooting), Tripod Mode (max speed 1m/s, reduced sensitivity, stable shooting).

3.14. Course Lock, Fix-wing Mode, SAR Mode

These modes are accessible in GNSS mode via the App mapping interface. Course Lock fixes the drone's forward direction. Fix-wing Mode allows only forward flight. SAR Mode displays GNSS coordinates for search and rescue.

3.15. One-Tap Short Film

Includes Sky, Selfie, Surround, Spiral, and Tail sub-modes. The drone automatically flies and shoots, then generates a short video. Start the drone and take it up to more than 5 meters above the ground before launching.

Important Note: Use One-Tap Short Film in open, unobstructed environments. Avoid obstacles. Vision system may not work properly in certain scenarios (e.g., obscured object, subject >50m away, similar colors, high speed, dark/bright environments, poor GNSS signal).

3.16. AI Super Night Video

The FIMI MINI 3 features a new generation AI ISP for enhanced low-light performance, capturing bright images at night. Supports up to 25600 ISO. The drone automatically detects light conditions and suggests enabling this mode.

Video 1: Comparison of FIMI MINI 3 and DJI MINI 4 night video performance.

Important Note: Recommended for night shooting. Supports 24/25/30fps. Does not support zoom.

3.17. 8K Hyperlapse Recording

Supports 8000x6000 ultra-high-definition images. Fly at a slower speed for optimal results. Recommended altitude of 50m or above. Select static objects at a distance of >15m. Does not support Super Night Mode, zoom, or portrait orientation.

4. Maintenance

4.1. Propellers Maintenance

Propellers are wearing parts. Replace them if damaged to ensure flight safety and efficiency.

4.2. Battery Maintenance

Do not throw the battery into fire or batter it. Lithium battery capacity reduces significantly in low temperatures. Do not use the battery below 0 degrees. Do not place the battery under direct sunlight. Recharge the battery every three months to maintain activity. Batteries not maintained for over three months are not covered under warranty. Store the battery and aircraft separately if not in use for a long time.

4.3. Gimbal Calibration

The FIMI MINI 3 gimbal is integrated and cannot be disassembled. Be careful not to scratch the camera and keep it clean. The gimbal is a precision component; do not squeeze it.

4.4. Drone Self-check

The drone performs a self-check when powered on. If it fails, the App will display corresponding hints.

4.5. Firmware Upgrade

Check the firmware version regularly. New versions will be prompted by the FIMI Navi Mini App. Download new firmware when the App is connected with the drone and remote controller. To query the product firmware version, enter the image transmission interface, click System Settings, pull down and select Others, then click Firmware Upgrade.

5. Troubleshooting

5.1. Common Issues and Solutions

  • Image Transmission Issues (No image on phone): For Samsung phones, activate developer mode and enable "USB debugging" in settings. Ensure the drone is properly connected to the phone via cable.
  • Gimbal Issues (Crooked gimbal, shaking drone): Calibrate the camera and drone. Perform gimbal calibration via the FIMI Navi Mini App. Ensure the drone is placed on a flat and stable surface during calibration.
  • Connection Problems (Cannot connect to drone/remote): Update firmware. Ensure the switch on the drone is set to function with the remote control, not Wi-Fi. Disconnect the control, turn everything off, and retry.
  • Horizon Issues (Horizon tilted in videos): This issue may be resolved with firmware updates.
  • Flight Instability / Reduced Speed / Shorter Battery Life: Check propellers for damage or deformation and replace if necessary.
  • Battery Issues (Battery not charging, damaged): If the battery detects cell damage or severe imbalance, it will indicate this. Ensure charging temperature is within 5°C to 40°C.
  • App Glitches: If using an older mobile device, it may affect app experience. Consider changing to a newer device.

5.2. Gimbal Calibration

If the gimbal is not activated or shows obvious tilt after self-test, calibrate it. Gimbal trim corrects roll and yaw offset. Ensure the drone is powered on and self-test is complete. Do not calibrate in flight. Choose a flat and stable environment.

Gimbal Fine-tuning

Adjust gimbal horizontal and yaw angle by ±10° in the fine-tuning interface. Click "+/-" for 0.1° adjustments or input values directly. Click "Default" to return to 0°.

5.3. Remote Control Calibration

If remote control operation and drone flight response are inconsistent, calibrate the remote control. Select Remote Control Calibration in the App. Do not touch sticks during calibration. Follow prompts for center and rocker calibration.

Important Note: Turn off the aircraft power when calibrating the remote control. Calibration cannot be done in flight.

6. Specifications

6.1. Drone

FeatureSpecification
ModelFMWRJ04A3
Dimensions (folded)145mm × 85mm × 56mm
Dimensions (unfolded)200mm × 145mm × 56mm
Takeoff WeightApprox. 245g
Diagonal Distance214mm
Max Ascent Speed5m/s
Max Descent Speed3.5m/s
Max Flight Speed18m/s (in windless environment at sea level)
Max Takeoff Altitude≤4000m
Max Hovering Time29 minutes
Maximum Flight Time32 minutes
Max Tilt Angle35°
Max Wind Speed Resistance10.7m/s
Operating Temperature Range0-40℃
Satellite Navigation SystemsBeidou/GPS/GLONASS/Galileo
Hovering Accuracy (Vertical)±0.1m (Vision Positioning) / ±0.5m (GPS)
Hovering Accuracy (Horizontal)±0.3m (Vision Positioning) / ±0.5m (GPS)

6.2. Remote Controller

FeatureSpecification
ModelFMYKQ04A3
Product WeightApprox. 260g
Dimensions165mm x 89mm x 47mm
Operating Frequency2.4000 GHz - 2.4835 GHz, 5.725 GHz - 5.850 GHz
Max Battery Life8 hours (without charging mobile device), 4 hours (charging mobile device)
Battery TypeLi-ion
Battery Capacity3500mAh
Nominal Voltage3.7V
Input5V ⎓ 2A
Operating Temperature Range0~40℃
Charging Temperature Range5~40℃
Max Signal Effective RangeFCC: Approximately 9 km (no interference, no obstruction)
Minimum LatencyApprox. 120 milliseconds
Supported Mobile Device Interface TypesLightning, USB-C

6.3. Gimbal

FeatureSpecification
TypeThree-axis Mechanical Gimbal
Controllable Rotation Range10° ~ -90° (Pitch)
Angular Vibration Range±0.005°

6.4. Camera

FeatureSpecification
Image Sensor1/2-inch CMOS
LensFOV 79°, Aperture f1.6, Format Length 4.71mm, Equivalent 24mm
Focus1m to ∞
Effective Pixels48 million pixels
ISO RangeVideo Manual 100-6400, Video Automatic 100-25600, Photo 100-6400
Shutter Speed1/8000s-2s
Max Photo Size8064 × 6048
Max Video Resolution3840×2160@60/30/25/24fps
Max Bitrate100Mbps
Video FormatMP4
File SystemFAT32/exFAT
Photo FormatJPG
Digital Zoom12x

6.5. Intelligent Flight Battery

FeatureSpecification
Capacity2200mAh
WeightApprox. 86g
Nominal Voltage7.7V
Charging Limited Voltage8.8V
Battery TypeLi-ion 2S
Energy16.94Wh
Charging Temperature5-40℃

6.6. APP System Requirements

  • iOS 12.0 or later
  • Android 9.0 or later

6.7. Noise Test Results

Observation PointFlight (6m/s)Hovering
Ground observation point (directly below)75.6 dB(A)76 dB(A)
Side observation point (at same elevation level)69.8 dB(A)68.6 dB(A)

7. User Tips

  • The FIMI MINI 3 offers excellent value for money, with stable flight and good camera performance.
  • The drone is portable and easy to set up, making it suitable for both adults and beginners.
  • Take advantage of advanced flight planning functions for complex shots.
  • The USB Type-C fast-charging battery allows for convenient charging with a phone charger.
  • The drone exhibits strong wind resistance, ensuring stable footage even in challenging conditions.
  • If you experience image issues or a crooked gimbal, perform calibration of the camera and drone through the FIMI Navi Mini App.
  • For Samsung phones experiencing image transmission problems, enable "USB debugging" in developer mode.
  • Keep the firmware updated to ensure optimal performance and access to new features.

8. Warranty and Support

FIMI provides tutorial videos and comprehensive manuals for the FIMI MINI 3. Users are advised to watch tutorial videos and read the FIMI MINI 3 Disclaimer and Safety Operation Instructions carefully before use. For more detailed product information, refer to the FIMI MINI 3 User Manual (PDF).

User Manual (PDF): A detailed user manual is available in PDF format. You can reference it for in-depth information on the drone's features and operations. The PDF can be downloaded from the official FIMI website.

FIMI Navi Mini App: Scan the QR code in the Quick Start Manual to download the FIMI Navi Mini App. The app provides real-time prompts, flight data, and firmware updates.

Contact Information:

Battery Warranty: Batteries not maintained (charged and discharged) for over three months are not covered under warranty.

9. Compliance

9.1. Disclaimer

⚠️ For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.