GELID GP-EXTREME

Contents

Gelid GP-EXTREME Thermal Pad User Manual

High-Performance Thermal Interface Material for CPU, GPU, and Motherboard Cooling

1. Product Introduction

The Gelid GP-EXTREME thermal pad is a high thermal conductivity, high flexibility interface filling material. It is designed to fill the gap between electronic components and heat sinks, effectively reducing thermal resistance and improving heat dissipation efficiency. This product is widely applicable to various electronic devices, including CPUs, GPUs, power modules, LED beads, and industrial control equipment.

2. Product Features

  • High thermal conductivity, low thermal resistance, and stable heat dissipation performance.
  • Soft and elastic, allowing it to adapt to uneven contact surfaces for optimal contact.
  • Insulating, temperature-resistant, aging-resistant, and designed for a long service life.
  • Self-adhesive for easy installation, and can be adjusted repeatedly if needed.
Gelid GP-EXTREME Thermal Pad with specifications
Image: Gelid GP-EXTREME Thermal Pad packaging displaying key specifications.

3. Application Scope

The thermal pad is suitable for heat conduction between various heating elements and their respective heat sinks. This includes, but is not limited to, CPUs, GPUs, chips, MOSFETs, power modules, LED beads, power batteries, and industrial control motherboards.

4. Specifications

Attribute Value
Brand GELID
Model Number GP-EXTREME
Type Thermal Pad
Thermal Conductivity 12 W/mK
Density 2.8 g/cm³
Hardness 35 Shore
Sizes Available 80x40mm (0.5mm, 1.0mm, 1.5mm, 2.0mm, 2.5mm, 3.0mm thicknesses)
120x120mm (0.5mm, 1.0mm, 1.5mm, 2.0mm, 2.5mm, 3.0mm thicknesses)
High-concerned chemical None
Origin Mainland China
Various sizes of Gelid GP-EXTREME thermal pads
Image: Assortment of Gelid GP-EXTREME thermal pads in different sizes and thicknesses.

5. Usage Steps

Follow these steps for proper installation of the thermal pad:

  1. Clean Contact Surfaces:

    Dip a lint-free cloth in anhydrous alcohol and thoroughly wipe the heating surface of electronic components and the bonding surface of the heat sink. This removes dust, oil stains, and any residual old thermal paste. Ensure the surfaces are completely dry, flat, and free of impurities before proceeding.

  2. Compare and Cut:

    Lay the thermal pad on the heating element to compare the size. Cut it with scissors as needed. The cut size should be slightly larger than the component's contact surface (reserve 1-2mm tolerance) to ensure full coverage.

  3. Peel Off One Side of Protective Film:

    The thermal pad has protective films on both sides. Pinch the edge of one protective film with your fingers and gently peel it off to expose the transparent adhesive surface. Avoid touching the adhesive surface with your fingers to maintain its integrity.

  4. Stick to the Heating Element:

    Align the adhesive side (without the protective film) of the thermal pad with the center of the component's heating surface and stick it smoothly. Press gently from the center outwards to expel any air, ensuring no bubbles, wrinkles, or lifting. This ensures optimal contact and heat transfer.

  5. Peel Off the Other Side of Protective Film:

    After confirming the thermal pad is firmly attached to the component, peel off the remaining protective film. Do not touch this surface to avoid dust contamination before installing the heat sink.

  6. Attach the Heat Sink and Press:

    Align the heat sink with the component and thermal pad, then press it smoothly. Use the palm of your hand to press the entire contact surface of the heat sink evenly to ensure the thermal pad is fully attached to the heat sink without gaps. Press evenly for full attachment.

  7. Fix and Inspect:

    Secure the heat sink with screws or buckles. Double-check that the thermal pad has no offset or exposure to avoid any short circuit risk. Installation is now complete.

Video: A demonstration of the Gelid GP-EXTREME thermal pads, showcasing various sizes and packaging details.

6. Important Notes

  • Ensure all contact surfaces are clean and dry before installation. Failure to do so may negatively affect thermal conductivity and adhesion.
  • Do not overstretch or squeeze the thermal pad excessively, as this can cause damage or uneven thickness. A compression ratio of 10%-30% is recommended.
  • Avoid scratching or piercing the thermal pad with sharp objects, which can compromise its insulation and thermal conductivity.
  • Store the thermal pad in a cool, dry place, away from high temperatures, humidity, and oil-contaminated environments.
  • This product is a consumable. Replace it in a timely manner if it shows signs of aging, hardening, or damage to maintain optimal performance.

7. Troubleshooting (FAQs)

Issue: Poor Thermal Conductivity

Causes: Contaminated contact surfaces, air bubbles trapped during installation, mismatched thermal pad thickness, or improper installation offset.

Solutions: Clean the contact surfaces thoroughly again, reattach the thermal pad carefully, or replace it with a thermal pad of the appropriate thickness for your component.

Issue: Insufficient Adhesion

Causes: Oil stains on the contact surfaces or incomplete removal of the protective film.

Solutions: Clean the contact surfaces thoroughly and confirm that the protective film is completely removed from both sides before reattaching the thermal pad.

Issue: Short Circuit Risk

Causes: Exposed thermal pad touching unintended circuit components.

Solutions: Cut the thermal pad to the appropriate size to ensure it does not extend beyond the component after installation, preventing contact with other circuit elements.

8. User Tips

  • Always measure the gap between your component and heatsink to select the correct thermal pad thickness. Using a pad that is too thin or too thick can reduce effectiveness.
  • When cutting, use a sharp blade or scissors to ensure clean edges, which helps with better contact.
  • Consider using a small roller or a flat tool to gently press the thermal pad onto the component after placement to ensure even contact and remove any trapped air.
  • For components with varying heights, multiple pads of different thicknesses might be required, or a single pad can be cut to fit specific areas.

9. Warranty and Support

For detailed warranty information and technical support, please refer to the official Gelid Solutions website or contact your retailer. A comprehensive user manual is also available in PDF format for download: Gelid GP-EXTREME User Manual (PDF).

© 2023 Gelid Solutions. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.