Introduction
This manual provides detailed instructions for the operation and maintenance of your SATLINK ST-2210 DVB-S2 Satellite Finder. Please read this manual thoroughly before use to ensure safe and proper operation and to maximize the device's performance and longevity.
Important Safety Instructions
- Be sure to read this user manual before starting your operation.
- You must install the dish with correct direction and angle. If the dish is not working properly, contact your local dealer.
- When the unit is suddenly moved to a hot area from a cold area, it may cause some problems. In that case, turn off the power, and turn on again after 1-2 hours.
- Keep meter placed in clean space with sufficient ventilation.
- Do not cover the meter with or place it on a unit that emits heat.
- Clean the case by a soft cloth with a little washing liquid.
- Do not remove the cover.
- Do not let the unit exposed to extreme heat, cold or humid conditions.
- No liquids or any other materials to come inside of the unit.
Unpacking
Open the package and make sure it includes all below items. If any are missing, please contact the reseller for replacement.
- Digital Satellite Meter
- User's manual
- Adaptor
Product Overview & Illustration
The SATLINK ST-2210 features a 3.95-inch TFT capacitive touch-screen for easy operation and clear value readings.
Below is an overview of the device's main features and components:
| No | Description | Function |
|---|---|---|
| 1 | LNB IN | Connect to satellite antenna cable |
| 2 | Battery Level Indicator | Displays the battery level when powered on |
| 3 | Power Switch | Turn on/off meter |
| 4 | Navigation Key | Move cursor and confirm operation |
| 5 | Menu Display | Display on/off menu list |
| 6 | Speaker | Sound and Light Alarm for Locking Signal |
| 7 | HD | Invalid |
| 8 | AV | Invalid |
| 9 | USB | Upgrade by PC |
| 10 | DC | DC 12V input port |
Key Features
- Compatible with all digital TV standards
- Fast and reliable signal data processing
- Patented dual-frequency spectrum scan and capture module
- Rich spectrum analysis functions
- Specific details of measurement statistics for channel quality
- Constellation for all kinds of digital TV signals
- Antenna/LNB angle calculation
- Satellite motor DiSEqC and dCSS MDU application support
- dCSS MDU support
- LNB power compensation
- Audible tone to reflect signal strength
- High-resolution LCD display
- Capacitive touch panel
- Friendly and intuitive graphical user interface
- High capacity lithium battery for long operation and storage hours
- USB interface for firmware upgrade and file transfer
- Built-in parameters for global satellites and transmitters
Setup
System Setup
The System Setup menu allows you to configure basic device settings.
- Language: Default is English.
- Location: Enter local longitude and latitude.
- Shutdown Time: Select Disable, 5 Minutes, 10 Minutes, or 20 Minutes.
- Volume: Adjust the volume level from Mute to Volume 4.
- Power Unit: Choose between dBm, dBuV, or dBmV.
- Voltage Plus: Configure LNB power compensation.
- Factory Reset: System will restore to default settings.
Satellite Editor
This menu allows you to manage satellite and transponder data.
- Sat Editor: Add, modify, and delete satellites from the database.
- TP Editor: Add, modify, and delete transponders.
Blind Scan
Before performing a blind scan, select a satellite for saving data. The 22K and LNB Power settings are used to limit blind scan conditions. Click the START button to begin scanning and the Save button to store data to the current satellite.
Operation
Measurement
To measure signal parameters, first select a satellite and transponder from the database or manually edit installation settings. The system will then calculate and display parameters such as Level, SNR, MER, BER, SSI, and SQI. You can choose between A/B/C view modes. Use the Report button to view the installation report and the Save button to save it to the Report List menu.
Constellation
The constellation display provides a visual representation of the signal quality. If parameters were set in the Measurement menu, they are automatically applied here. Click the icon to enlarge the constellation information; click again to return to the original display.
Spectrum
The Spectrum function provides a real-time spectrum display. The X-axis represents frequency, and the Y-axis represents amplitude. You can adjust the display range of amplitude by sliding up and down, and change the start, stop, and center frequencies by sliding left and right.
Editing options include:
- Frequency: Start, Center, Stop, Span, Display Mode (IF mode and TP mode).
- Amplitude: Reference (-80dBm to 0dBm), dB/Div (2 to 20dB), Unit (dBm/dBuV/dBmV).
- Marker: Up to two marker lines can be displayed, showing Level and Frequency in real-time.
- Trace: Options include Max Hold (saves greater values) and Min Hold (saves smaller values).
- Pause: Temporarily halts the spectrum display.
Multi-TP Scan
Select a satellite and up to 10 transponders for scanning. The results can be saved as a report.
Motor Test
This function supports DiSEqC 1.2 and USALS motor types. It displays SSI and SQI in real-time. Commands include Move, Goto Satellite, Goto 0, Reset, Clear Limit, Store Position, Set Limit, and Enable Limit. You can also set Move Step (Continue, 1/2/3/4 Step) and Direction (East, West).
DiSEqC Test
Test DiSEqC functionality with options for Band Switch and Port Switch. Band Switch supports Unicable 1.0 and 2.0. Port Switch supports DiSEqC 1.0 (ports 1-4) and DiSEqC 1.1 (ports 1-16).
Angle Calculation
Before calculating angles, ensure the following parameters are set: Satellite, Position (Latitude, Longitude), Dish Type (Axi_symmetric or Offset), and Offset Angle (if applicable). Click the Calculate button to determine azimuth, polarization, and elevation angles.
Limit Configuration
Configure Common Settings (Max Level, Min Level, BER) and SNR Threshold Settings. If any set limit is exceeded, a warning will appear in the Measurement interface.
Report List
View, delete, or rename saved reports. Reports can be filtered by All File, Signal Params File, or Spectrum Report File.
Maintenance
- Cleaning: Clean the device case with a soft cloth and a small amount of washing liquid.
- Protection: Do not remove the cover. Avoid exposing the unit to extreme heat, cold, or humid conditions. Ensure no liquids or other materials enter the unit.
- Ventilation: Always place the meter in a clean space with sufficient ventilation and do not cover it or place it on heat-emitting units.
Troubleshooting
- Dish Malfunction: If the satellite dish is not working properly, contact your local dealer for assistance.
- Temperature-Related Issues: If the unit is moved from a cold to a hot area and experiences problems, turn off the power and wait 1-2 hours before turning it on again.
Specifications
DTV Standards Compliance
| Standard | Compliance |
|---|---|
| DVB-S | ETSI EN 300-421 v1.1.2 |
| DVB-S2 | ETSI EN 302-307 v1.4.1 |
Spectrum Analysis
| Parameter | Value |
|---|---|
| Band Mode | Satellite or Terrestrial/Cable |
| Min. Resolution | 10 kHz |
| SPAN Range | Satellite: 25 to 1200MHz; Terrestrial/Cable: 25 to 950MHz |
| Input Frequency Range | Satellite: 900 to 2150MHz; Terrestrial/Cable: 50 to 1000MHz |
| Trace Mode | Auto, Max Hold |
| Frequency Display Mode | TP Frequency or IF Frequency |
| Frame Speed | 10 frames/sec. (typical) |
| Attenuator | 0 to 60dB |
| Average | 1 to 20 |
| Marker | 2 Markers |
| dB/Div Resolution | 5 to 20dB |
| Unit | dBm or dBuV |
| Measurement | Run / Pause Switchable |
General
| Parameter | Value |
|---|---|
| LCD | 3.95', 480 x 3RGB x 320, 16-bit Color |
| Touch Panel | Capacitive Touch |
| Active touch area | 55.68(W) * 83.52(H)MM² |
| Power Adapter | 12VDC / 1A |
| Battery | 2Cell / 2500mAh |
| Power Consumption | 8W max. |
| Dimension (W x D x H) | 8.27' x 3.07' x 1.06' (210 x 78 x 27mm) |
| Interface | USB 2.0 x 1 |
| Function | Firmware Upgrade; Satellite/TP and Terrestrial/Cable Channel Plan Modification |
Satellite (DVB-S/S2)
| Parameter | Value |
|---|---|
| Connector | 75Ω F |
| Input Frequency | 950 to 2150MHz |
| Input Level | -80 to -10dBm |
| LNB Power Supply | 14V / 18V / OFF, Imax 650mA |
| Port Switch | DiSEqC 1.0, DiSEqC 1.1 |
| Motor Control | DiSEqC 1.2, USALS |
| Unicable/dCSS | EN50494, EN50607 |
| Symbol Rate | 1M to 45M symbols/sec. |
| RollOff | 0.35 / 0.25 / 0.2 |
| Constellation | DVB-S2: 8PSK/QPSK; DVB-S: QPSK |
| Code Rate | DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10 DVB-S2 QPSK: 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 4/5, 5/6, 8/9, 9/10 DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8 |
| Satellite Database | Europe, Asia, American, Atlantic |
dCSS
| Parameter | Value |
|---|---|
| Band | EN50494 8UB, EN50607 32UB |
| UB Center frequency | Preset or User Defined |
| Satellite Number | EN50494 2-Satellite, EN50607 4-Satellite |
| Pin Code | Yes |
| Bandwidth | 6MHz, 8MHz |
| Guard Interval | 1/64, 1/128 |
| Constellation | 16, 64, 256, 1024QAM |
| Code Rate | 2/3, 3/4, 4/5, 5/6, 8/9, 9/10 |
| Data Slices | Types 1/2 |
| Interleaving Modes | 4, 8 Symbols or Best-Fit Time |
User Tips
- To maximize battery life, ensure the device is fully charged before use and avoid extreme temperatures.
- Regularly check for firmware updates via the USB interface to ensure optimal performance and access to new features.
- When performing a blind scan, ensure you have selected the correct satellite to save data to prevent overwriting important information.
Warranty and Support
For warranty information and technical support, please contact your local dealer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
A detailed user manual is also available in PDF format for download: User manual (PDF)
Product Video
Watch this video for a demonstration of the SATLINK ST-2210 DVB-S2 Satellite Finder.
Product demonstration video for the SATLINK ST-2210.