Introduction
Thank you for choosing SHIMANO B05S Resin Brake Pads. These brake pads are designed to provide reliable and consistent braking performance for a wide range of Shimano hydraulic disc brake systems. The B05S model is an upgraded version, replacing the B03S, which itself was an upgrade to the discontinued B01S. This manual provides essential information for proper installation, operation, maintenance, and troubleshooting to ensure optimal performance and safety.
Compatibility
The B05S Resin Brake Pads are compatible with a broad range of Shimano hydraulic disc brake calipers. Please refer to the list below and the compatibility chart for specific models:
- BR-M575, BR-M525, BR-M495, BR-M486, BR-M485, BR-M475, BR-M465, BR-M447, BR-M446, BR-M445, BR-M416, BR-M416A, BR-M4050, BR-M395, BR-M375, BR-M365, BR-M355, BR-M315, BR-T675, BR-T615, BR-TX805, BR-UR300
Setup and Installation
Before beginning installation, ensure your bicycle is stable and secure. It is recommended to wear appropriate safety gear, such as gloves and eye protection.
Components Overview:
Installation Steps:
- Remove Wheel: Carefully remove the wheel from the bicycle frame.
- Remove Old Pads:
- Remove the locating pin (often secured with a split pin or screw) that holds the brake pads in place.
- Using pliers or a flathead screwdriver, gently pry apart the brake caliper pistons to create space.
- Remove the old brake pads and the spring clip. Note their orientation.
- Clean Caliper: Clean the inside of the brake caliper with isopropyl alcohol to remove any residue or brake dust. Ensure pistons are fully retracted.
- Install New Pads:
- Place the new spring clip between the new brake pads, ensuring it sits correctly.
- Insert the new pads and spring clip into the caliper, making sure the friction material faces the rotor.
- Reinsert the locating pin through the pads and caliper, securing it with its retaining clip or screw.
- Reinstall Wheel: Reinstall the wheel, ensuring it is properly seated in the dropouts and quick release/thru-axle is tightened to manufacturer specifications.
- Check Brake Lever: Pump the brake lever several times until the pads engage the rotor and the lever feels firm. Check for proper clearance between pads and rotor.
- Bed-in New Pads: Perform the bed-in procedure (see Operating section) before riding at full speed.
Operating Instructions
Bedding-in New Brake Pads:
New brake pads require a 'bedding-in' period to achieve optimal performance. This process transfers a layer of pad material onto the rotor, improving friction and reducing noise.
- Find a safe, open area where you can accelerate and brake repeatedly.
- Accelerate to a moderate speed (e.g., 15-20 mph or 25-30 km/h).
- Apply the brakes firmly but gradually, slowing down to a walking pace. Do not come to a complete stop.
- Repeat this process 10-20 times for each brake (front and rear).
- Allow the brakes to cool down between sets of repetitions.
- You should notice an increase in braking power and a more consistent feel.
Performance Characteristics:
SHIMANO Resin Brake Pads are known for:
- Low Noise: Generally quieter than metallic pads, especially in dry conditions.
- Good Modulation: Offer a progressive braking feel, allowing for fine control.
- Reduced Rotor Wear: Kinder to rotors compared to metallic pads.
- Consistent Performance: Provide reliable stopping power in various conditions, though performance may slightly decrease in very wet or muddy environments.
Maintenance
Regular maintenance ensures the longevity and safety of your braking system.
- Regular Inspection: Periodically check the thickness of the brake pad material. Replace pads when the friction material is worn down to 0.5mm or less, or if the spring clip is touching the rotor.
- Cleaning: Keep brake pads and rotors clean. Avoid getting oil, grease, or brake fluid on the pads or rotor surface, as this can contaminate them and severely reduce braking performance. Clean rotors with isopropyl alcohol.
- Rotor Condition: Inspect rotors for excessive wear, warping, or damage. Replace damaged rotors immediately.
- Brake Fluid: Ensure your hydraulic brake system has adequate and clean brake fluid. Refer to your brake caliper's manual for fluid type and bleeding procedures.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced Braking Power | Pads or rotor contaminated with oil/grease; pads worn out; improper bed-in. | Clean pads/rotor with isopropyl alcohol (replace if heavily contaminated); replace worn pads; re-perform bed-in procedure. |
| Squealing/Whistling Noise | Pads or rotor contaminated; improper alignment; new pads not bedded-in; pads overheating. | Clean pads/rotor; realign caliper; bed-in pads; ensure proper cooling during prolonged braking. Note: Resin pads may occasionally whistle when hot, which can be a characteristic. |
| Brake Lever Feels Spongy | Air in hydraulic system; low brake fluid. | Bleed the brake system; top up brake fluid (refer to caliper manual). |
Specifications
| Feature | Description |
|---|---|
| Brand | SHIMANO |
| Model | B05S (Replaces B03S, B01S) |
| Braking System | Hydraulic Disc Brake (Hydraulic Brake Pad) |
| Components | Pads |
| Material | Steel metal back plate + metal particles and resin sintered matrix |
| Features | Super-forced power and life, low noise, good feel |
| Origin | Malaysia |
| Approximate Dimensions (B01S reference) | Pad Length: 30.5mm, Pad Height: 19mm, Total Length (with tab): 35mm, Width: 31mm, Thickness: 4mm |
User Tips
- Model Evolution: Remember that B01S pads have been discontinued and replaced by B03S, and subsequently B05S. The B05S is the latest upgraded version, offering improved performance over its predecessors.
- Rotor Compatibility: These are resin pads. Always ensure your brake rotors are compatible with resin pads. Rotors often have 'Resin Pad Only' or 'Metal Pad Compatible' markings.
- Noise Management: While resin pads are generally quiet, some users report whistling, especially when heated. Proper bedding-in is crucial to minimize this. If noise persists, check for contamination or misalignment.
- Genuine Product: Always purchase from reputable sources to ensure you receive genuine Shimano products for optimal safety and performance.
Warranty and Support
SHIMANO products are manufactured to high standards and are covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, conditions, and support, please refer to the official SHIMANO website or contact your authorized SHIMANO dealer. Keep your proof of purchase for warranty claims.