1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your VSETT Throttle & NFC Card. This original VSETT component is designed for enhanced control and security of your electric scooter.
Compatibility:
- VSETT series electric scooters: VSETT 8, 8+, 9, 9+, 10+, 11+ (60V models).
- ZERO series scooters: ZERO 8, 9, 10, 8X, 10X, Z8PRO.
- Other factory-made scooters: KUGOO X1/G1, and corresponding models of Quick Volt, Eco Speed, Ecobee, Country man, Turbowheel, Apollo, Go green, Muvter, Techlife.
Important Note: This throttle is NOT compatible with ZERO 11X/SPEEDUAL PLUS models.
Supported Voltage Levels: 24V, 36V, 48V, 52V, 60V.
2. Safety Information
⚠️ Please mind potential fire risk and strictly follow the instruction manual for charging and storage of your scooter's battery.
- Always ensure all screws and connections are tightened securely before riding.
- Installation and adjustment of this item require high hands-on ability and electrical knowledge. If you lack such skills, please consult a professional mechanic.
- Avoid exposing the throttle and NFC card to excessive moisture or extreme temperatures.
3. Product Overview
The VSETT Throttle & NFC Card unit integrates a throttle, display, control buttons, and an NFC card reader for secure scooter activation.
4. Installation
The throttle unit connects to your scooter's wiring harness via a 6-pin connector.
Installation Steps:
- Carefully remove your existing throttle and display unit, if applicable.
- Connect the 6-pin connector of the new VSETT Throttle & NFC Card to the corresponding port on your scooter's wiring harness.
- Mount the throttle unit securely on your handlebar.
- Ensure all connections are firm and no wires are pinched.
- Test the functionality before riding.
Warning: We do not provide installing tools or a detailed manual for physical installation. This process requires high hands-on ability and electrical knowledge. If you are not confident, please seek assistance from a professional mechanic to avoid damage to the product or your scooter.
5. Operating Instructions
The VSETT display provides essential information and control over your scooter's functions.
5.1. Displayed Content
- Speedometer: Current speed (MPH/KM/H).
- Odometer (ODO): Total distance traveled.
- Trip Meter (TRIP): Distance traveled per trip.
- Battery Indicator: Current battery level.
- Cruise-control active light: Indicates when cruise control is active.
- Gear indicator: Current speed gear (0-3 digital display).
- Fault warning light: Indicates system errors.
- Current voltage value (VOL): Displays real-time voltage.
5.2. Basic Operation
- Power On/Off: Long-press the Mode/Enter button for 2 seconds.
- Switch Display Interface: When powered on, short press the Mode/Enter button to cycle between ODO, TRIP, and VOL displays.
- Change Gear: When powered on, press the '+' or '-' button to change the speed gear.
5.3. NFC Card Binding
The VSETT series supports NFC (Near Field Communication) for secure scooter activation. NFC cards are bound by factory default.
Initial State (Instrument not bound to ID card):
After starting up, the LCD displays normal content, and the card swiping area displays the power voltage. At this time, the meter can directly enter the working state without an NFC card swipe.
Binding an ID Card (Late Setting):
To bind a new NFC card or use a mobile phone with NFC functionality:
- Long press the Mode/Enter button for 5 seconds until the display shows 'B 0'.
- Place the ID card (or NFC-enabled phone) close to the card swiping area.
- The display will show 'B 1' if the card is successfully tied. The default setting allows unlimited use of the bound card.
Unbinding ID Cards:
- Long press the Mode/Enter button for 5 seconds until the display shows 'C 0'.
- All ID CARDS that have been unbound will be displayed.
Bound State (Instrument bound with ID card):
After starting up, the LCD displays 'Card', the power voltage is not displayed, and the swiping indicator flashes. The NFC card needs to be swiped to start up the scooter; the accelerator will not work without a successful swipe.
Each E-Scooter is typically equipped with 3 NFC keys.
6. Display P-Codes (Programming)
To access the P-code menu for advanced settings, long-press the '+' and '-' buttons simultaneously. Use the Mode/Enter button to scroll through P-codes, and the '+' or '-' buttons to change parameters. Press Mode/Enter to save the value and switch to the next parameter. To exit, long-press '+' and '-' again, or wait 8 seconds for automatic exit and save.
| P-Code | Description | Range/Options | Default |
|---|---|---|---|
| P01 | Backlight brightness | 1 (darkest) - 3 (brightest) | 3 |
| P02 | Mileage unit | 0: KM, 1: MILE | KM |
| P03 | Voltage level | 24V, 36V, 48V, 52V, 60V | N/A (Set to scooter voltage) |
| P04 | Dormancy time | 0: no dormancy, 1-60 minutes | 5 |
| P05 | Reserve | N/A | N/A |
| P06 | Wheel diameter | Unit in inch, accuracy 0.1 | 10.0 |
| P07 | Speed measuring magnetic steel number | 0-255 | 28 |
| P08 | Rate-limiting | 0-100km/h | 100 |
| P09 | Zero start | 0: zero start, 1: non-zero start | 0 |
| P10 | Reserve | N/A | N/A |
| P11 | EABS switch choose | 1 (weakest) - 5 (strongest) | 3 |
| P12 | Soft and hard start strength | 1 (softest) - 5 (hardest) | 3 |
| P13 | Reserve | N/A | N/A |
| P14 | Reserve | N/A | N/A |
| P15 | Controller under-voltage | N/A | N/A |
| P16 | ODO Zero setting | Long press '+' for 5 seconds to clear ODO | N/A |
| P17 | Cruise control enable | 0: cannot use cruise, 1: can use cruise | 0 |
| P18 | Bind and unbind NFC CARDS | Long press '+' to bind, long press '-' to unbind | N/A |
| P19 | Reserve | N/A | N/A |
| P20 | Communication protocol | Defaults 4 (cannot change) | 4 |
7. Maintenance
- Keep the throttle and display unit clean and free from dust and debris.
- Regularly check all electrical connections for tightness and signs of wear.
- Avoid using harsh chemicals for cleaning; a soft, damp cloth is sufficient.
- If NFC cards are lost, contact your local dealer or agent for replacements.
8. Troubleshooting
- Display shows 'Card' and scooter does not accelerate: This indicates the unit is in a bound state. Swipe a registered NFC card over the reader to activate the scooter.
- Unable to bind new NFC card/phone: Ensure you are in the correct binding mode ('B 0' displayed) and that your phone's NFC function is enabled and correctly positioned over the reader.
- Display contents differ from manual: Due to product upgrades, some displayed contents may vary. This typically does not affect normal use.
- No power to display: Check all electrical connections, especially the 6-pin connector, to ensure they are securely attached. Verify the scooter's main power is on.
9. Specifications
| Feature | Specification |
|---|---|
| Type | Throttle |
| Brand Name | MACURY |
| Model Number | VSETT |
| Origin | Mainland China |
| High-concerned chemical | None |
| Supported Voltage | 24V/36V/48V/52V/60V |
| Connector Type | 6-pin |
| Package Weight | 0.4 kg |
| Package Dimensions (L x W x H) | 10cm x 10cm x 10cm |
10. User Tips
- For some scooter models (e.g., Kugoo G Booster), installation may require soldering and re-wiring of the connector, as the native wiring might differ. Professional installation is highly recommended in such cases.
- When using your phone as an NFC key, ensure your phone's NFC function is activated before attempting to bind it.
- Always double-check all connections after installation to prevent issues during operation.
11. Warranty and Support
For specific warranty information, please refer to the terms provided by your seller or the manufacturer at the time of purchase. In case of lost NFC cards, it is recommended to contact your local agents for assistance.
For technical support or complex installation issues, consulting a certified electric scooter mechanic is advised.