NERIES SL-QX065QZ

Contents

NERIES SL-QX065QZ Electric Bicycle Brushless Controller and S866 LCD Instrument Set User Manual

Model: SL-QX065QZ | Brand: NERIES

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your NERIES Electric Bicycle Brushless Controller and S866 LCD Instrument Set. This system is designed for electric bicycles operating at 24V, 36V, or 48V with 250W or 350W motors, offering intelligent control for a smooth and responsive riding experience.

Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety Information

  • Fire Risk: Please be aware of potential fire risks. Strictly follow all instructions for charging and storage of your e-bike battery and related components.
  • Compatibility: This product only supports single Hall sensors or dual Hall sensors with a duty cycle of 60% or higher. Ensure your motor's Hall sensors are compatible.
  • Brake System: The controller operates at a low level. If your e-bike's brake system uses a high-level Hall sensor, it may not be supported. Verify compatibility before installation.
  • Professional Installation: If you are unsure about any installation steps, seek assistance from a qualified technician. Incorrect wiring can damage the components or lead to unsafe operation.
  • Water Exposure: Avoid exposing the controller and LCD instrument to excessive moisture or water. While designed for outdoor use, direct submersion or heavy rain can cause damage.

3. Package Contents

Upon opening your package, please verify that all items are present and undamaged:

  • 1 x Brushless Controller
  • 1 x S866 LCD Instrument (Style A or B, depending on selection)
  • 2 x User Manuals
Product components in packaging, including the controller, LCD display, and manual.

Figure 3.1: Contents of the product package.

4. Specifications

FeatureDescription
BrandNERIES
ModelSL-QX065QZ
TypeElectric Bicycle Brushless Controller & LCD Instrument Set
Instrument StyleA / B (Two options)
Voltage24V / 36V / 48V (Auto-sensing)
Power250W / 350W
Current Limit13A
Motor Phase Angle120° / 60°
Controller MaterialAluminium alloy, capacitance, circuit board, wiring harness
Instrument MaterialABS, LCD, electronic chip
Controller Dimensions8.7 cm x 5 cm x 3 cm
Instrument Dimensions8 cm x 4.8 cm x 4.8 cm
Total Weight (incl. packaging)364g
Diagram showing the dimensions of the controller and the S866 LCD instrument.

Figure 4.1: Dimensions of the controller and S866 LCD instrument.

5. Setup and Installation

Carefully follow these steps to install your brushless controller and LCD instrument set. Ensure the e-bike's power is OFF before beginning installation.

5.1 Wiring Diagram

Detailed wiring diagram for the electric bicycle brushless controller, showing connections for motor, battery, LCD, brakes, throttle, and sensors.

Figure 5.1: Controller Wiring Diagram

Refer to the diagram above for connecting the controller to your e-bike components. Key connections include:

  • Coarse Black (Negative Pole) P- / Rough Red (Positive Electrode) P+: Connect to your e-bike battery.
  • Phase Line of Brushless Motor: Connect the three thick wires to the motor's phase lines.
  • Main Electric Door Lock: Connect the ignition switch.
  • Connected to LCD: Connect the S866 LCD instrument cable.
  • Adjustable Linear Electronic Brake: Connect your e-bike's brake levers.
  • Headlamp Power Supply: If using the display to control headlights, connect the headlights to the two core cables of the display.
  • Intelligent Phase Recognition: These are the two green wires used for self-learning.
  • Pulse Assist Sensor (PAS): Connect the pedal assist sensor.
  • Turn the Handle: Connect the throttle.
  • Motor Hall Sensor: Connect the motor's Hall sensor wires.
  • Brake Power Off: Connect the brake cut-off sensor.

5.2 Initial Setup and Self-Learning

  1. After connecting all components according to the wiring diagram, ensure the e-bike is stable and safe to operate.
  2. Turn on the e-bike's power.
  3. Set the S866 LCD display to the highest gear (usually PAS level 9).
  4. Locate the two green wires on the controller labeled 'Intelligent Phase Recognition'. Connect these two wires together. The motor should start rotating.
  5. If the motor rotates in the correct direction, disconnect the two green wires. The self-learning process is complete.
  6. If the motor rotates in the wrong direction, disconnect the two green wires, then reconnect them. The motor should now rotate in the opposite direction. Once it rotates correctly, disconnect the wires.
  7. Once self-learning is complete, you can proceed to operate the e-bike.

6. Operating Instructions (S866 LCD Instrument)

The S866 LCD instrument provides essential information and control over your e-bike system. Refer to the diagram below for button functions and display indicators.

Detailed S866 LCD instrument user manual page showing button functions, display indicators, multi-function area, fault codes, and P-menu settings.

Figure 6.1: S866 LCD Instrument User Manual Overview

6.1 Function and Display

  1. Action button UP key (+)
  2. Action button SW key (Power)
  3. Action button DOWN key (-)
  4. 6 segment electricity indication
  5. Brake Status Tips
  6. Lights on tips
  7. TM Single ride time
  8. CUR Current speed
  9. AVG Average speed
  10. MAX Maximum speed
  11. MPH Ride speed (English)
  12. KMH Ride speed (Metric)
  13. DST Single ride mileage
  14. VOL Battery Real-time Voltage Display
  15. PAS Power Drive State Tips
  16. THL Turn on lights
  17. 6 km/h Boost status prompt
  18. Fixed-speed cruise alert

6.2 Operational Functions

  • Turn On/Off: Long press the Power button to turn on/off the display. If the instrument is not operated for 10 minutes, it will automatically shut down.
  • Display Interface Switching: Long press the Power button to switch between display interfaces.
  • Turn On Lights: Long press the '+' button to turn on/off the backlight and headlamp.
  • Power Shift: Short press '+' or '-' to shift between power gears (0-9). Gear 0 means no power output. Each boost button corresponds to the initial gear.
  • Enabling Function (6 km/h Boost): Hold the '-' key. The gear area shows the symbol P. Release the key to exit the function.

6.3 Multi-Function Area Display

The multi-function area displays various parameters. Short press the Power button to cycle through: ODO (total mileage), TRIP (single mileage), VOL (battery voltage), CUR (current), AVG (average speed), MAX (maximum speed).

6.4 Fault Code Display

The instrument displays error codes to indicate system malfunctions:

  • 0: Normal state
  • 1: Reserved state
  • 2: Brake fault
  • 3: Sensor fault
  • 4-6 KM/H: Cruise fault
  • 5: Constant speed cruise
  • 6: Battery undervoltage
  • 7: Motor failure
  • 8: Handle failure
  • 9: Controller failure
  • 10: Communication reception fault
  • 11: Communication transmission failure
  • 12: BMS failure
  • 13: Headlamp failure

6.5 P01-P20 Menu Display and Meaning

To enter the P-menu settings, long press the '+' and '-' buttons simultaneously. Use '+' and '-' to navigate between P-parameters and short press the Power button to enter a parameter. Long press the Power button to save changes and exit.

  • P01: Backlight brightness level (1-3, 3 is brightest)
  • P02: Mileage unit (0: KM, 1: Mile)
  • P03: Voltage rating (24V, 36V, 48V, 60V; default 36V)
  • P04: Dormancy time (0: no dormancy, 1-60: minutes)
  • P05: Power gear (0: 3 gears, 1: 5 gears, 2: 9 gears)
  • P06: Diameter (inch, accuracy 0.1)
  • P07: Speed measurement magnetic steel number (range 1-255)
  • P08: Speed limit (range 0-100 km/h)
  • P09: Zero start/Non-zero start settings (0: zero start, 1: non-zero start)
  • P10: Drive mode set (0: power drive, 1: electric drive, 2: power drive + electric drive)
  • P11: PAS sensitivity setting (range 1-24)
  • P12: Power start strength setting (range 1-5)
  • P13: Power magnetic steel disk type setting (5, 8, 12 grain magnetic steel)
  • P14: Controller limit value (default 12A, range 1-20A)
  • P15: Controller undervoltage setting
  • P16: ODO zero setting (long press '+' for 5 seconds to clear ODO)
  • P17: Not enable cruising (0: enable cruising, 1: automatic cruising optional)
  • P18: Proportional adjustment setting (range 50-150)
  • P19: P0.2 protocol (1: standard, 2: standby, 3: standby)
  • P20: Communication protocol (0: P0.2 protocol 1, 1: P0.2 protocol 2, 2: P0.2 protocol 3)

7. Maintenance

  • Cleaning: Wipe the controller and LCD instrument with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
  • Storage: Store the e-bike in a dry, cool place away from direct sunlight and extreme temperatures.
  • Inspection: Regularly inspect the controller and display for any signs of physical damage, such as cracks or frayed wires.

8. Troubleshooting

This section addresses common issues you might encounter with your controller and LCD instrument set.

Problem / Error CodePossible CauseSolution
Error E10 (Communication Reception Fault)Issue with communication between controller and display.Check the connection cable between the controller and the S866 LCD instrument. Ensure it is securely plugged in and not damaged. Restart the system.
Error 7 (Motor Failure)Problem detected with the motor.Check motor phase wires and Hall sensor connections. Perform the self-learning procedure again (Section 5.2). If the issue persists, the motor may be faulty.
PAS (Pedal Assist Sensor) not working or erraticPAS sensor connection issue, incorrect P-menu setting, or incompatible sensor.Verify PAS sensor wiring. Check P11 (PAS sensitivity) and P13 (magnetic steel disk type) settings in the P-menu. Ensure your PAS sensor is compatible (single Hall or 60%+ duty cycle dual Hall).
6-cable Hall sensor connection (controller has 5)Incompatibility with motor's Hall sensor configuration.This controller supports single Hall sensors or dual Hall sensors with a duty cycle of 60% or higher. If your motor has a different Hall sensor configuration (e.g., 6-wire), it may not be compatible. Consult a specialist.
Brakes not working (high-level Hall brake)Controller is low-level, incompatible with high-level Hall brakes.The controller is designed for low-level brake signals. If your e-bike uses high-level Hall brakes, they may not be compatible. Consider replacing the brake levers with low-level ones or using a compatible adapter if available.
No power/display not turning onBattery connection issue, faulty controller/display, or main electric door lock issue.Check battery connections (P+ and P-). Ensure the main electric door lock is functioning. Verify battery voltage.

9. User Tips

  • Controller-Display Matching: The controller is designed to work optimally with the provided S866 display. If you are purchasing only the controller, be aware that compatibility with other sellers' displays is not guaranteed.
  • Self-Learning is Key: Always perform the self-learning procedure (Section 5.2) after initial installation or if you experience motor rotation issues. This calibrates the controller to your motor.
  • Headlight Control: To control your e-bike's headlights via the S866 display, ensure the headlights are connected to the designated two-core cables from the display.
  • Understanding P-Settings: Familiarize yourself with the P01-P20 settings (Section 6.5) to customize your riding experience, such as speed limits, PAS sensitivity, and power gears.

10. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

For further assistance, please refer to the official NERIES website or contact their customer service.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.