1. Introduction
This manual provides instructions for the safe and effective use of the KKMOON Aluminum LED Remover Heating Soldering Platform. This device is designed for disassembling LED light beads, FPC boards, and for BGA solder ball applications, featuring automatic constant temperature control and a PTC heating element.

Figure 1: KKMOON Aluminum LED Remover Heating Soldering Platform
2. Safety Information
- Always wear appropriate personal protective equipment (PPE), including heat-resistant gloves and safety glasses, when operating the heating platform.
- Ensure the device is placed on a stable, heat-resistant surface away from flammable materials.
- Do not touch the heating surface when the device is powered on or immediately after use, as it reaches high temperatures (up to 260°C). Allow sufficient time for cooling.
- Ensure proper ventilation in the work area to dissipate fumes from soldering or desoldering.
- Do not immerse the device in water or any other liquid.
- Keep out of reach of children and pets.
- Only use the specified input voltage (110V or 220V) for your model.
- Disconnect the power supply when not in use or before cleaning.
3. Package Contents
Verify that all items are present in the package:
- 1 x Heating Plate (Model YG400W-W or YG400W-N)
- 4 x Pairs of Screw Nut (for attaching feet)

Figure 2: Included screws and feet components
4. Setup
Before operating the heating platform, follow these steps for proper setup:
- Attach the Feet: Locate the four pairs of screw nuts and the corresponding holes on the underside of the heating plate. Securely attach the feet to elevate the heating plate, ensuring stability and proper airflow for heat dissipation.
- Placement: Place the assembled heating platform on a flat, stable, and heat-resistant workbench. Ensure there is adequate space around the device for ventilation.
- Power Connection: Connect the power cord to the heating platform and then plug it into a suitable electrical outlet matching the device's voltage (110V or 220V).

Figure 3: Heating platform with feet attached
5. Operating Instructions
The heating platform features automatic constant temperature control, simplifying operation.
- Power On: Plug in the device. The heating plate will immediately begin to heat up.
- Heating Time: The platform will reach approximately 260°C (±10°C) within 30 seconds. The PTC heating element ensures rapid and stable temperature.
- LED Light Bead Disassembly:
- Carefully place the LED light bead or FPC board onto the hot surface of the heating plate.
- Allow the heat to transfer to the component, melting the solder.
- Using appropriate tools (e.g., tweezers, suction pen), gently remove the component once the solder has liquefied.
- BGA Solder Ball Work: The platform can also be used for BGA solder ball reballing processes. Place the BGA component on the heated surface to melt existing solder or to reflow new solder balls.
- Power Off: Unplug the device from the power outlet when finished. The plate will begin to cool down.

Figure 4: Example of LED light bead removal using the heating platform

Figure 5: LED strip on the heating platform
6. Maintenance
- Cleaning: Ensure the device is unplugged and completely cool before cleaning. Use a soft, dry cloth to wipe the aluminum surface. Do not use abrasive cleaners or solvents.
- Storage: Store the heating platform in a dry, dust-free environment when not in use.
- Inspection: Periodically inspect the power cord for any signs of damage. If damaged, discontinue use and seek professional repair.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not heat up. | No power supply; faulty power cord/outlet. | Check if the device is properly plugged in. Test the outlet with another device. Inspect the power cord for damage. |
| Temperature is not stable. | Environmental factors; internal component issue. | Ensure the device is not in a drafty area. If the issue persists, contact support. |
| Slow heating. | Insufficient power; environmental factors. | Verify the power supply meets the device's requirements. Ensure proper ventilation. |
8. Specifications
| Feature | Specification |
|---|---|
| Main Color | Silver |
| Main Material | Aluminum |
| Input Voltage | 110-voltage or 220-voltage (model dependent) |
| Power | 400W |
| Max. Temperature | 260°C (±10°C) |
| Heating Time to 260°C | Approx. 30 seconds |
| Item Size | 120 x 70 mm / 4.7 x 2.8 inches |
| Item Weight | 79 g / 2.8 ounces |
| Package Size | 160 x 110 x 15 mm / 6.3 x 4.3 x 0.6 inches |
| Package Weight | 97 g / 3.4 ounces |

Figure 6: Heating platform showing voltage specification (110V model)
9. User Tips
- For delicate components, consider pre-heating the board slightly with a hot air gun before placing it on the platform to minimize thermal shock.
- Always use non-marring tools (e.g., plastic or bamboo tweezers) to handle components on the hot plate to avoid scratching the surface or damaging parts.
- Keep the heating surface clean from solder residue to ensure even heat distribution and prevent contamination.
- Practice on scrap boards or components before working on valuable items.
10. Warranty and Support
This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Please retain your proof of purchase.